If R1=0x00009300 and R2=0x00009000, evaluate the following program and determine th content of registers RO-R4 for the following program. Assume the processor access data in lit endian system LDR RO,=0×67983A5C STR RO, [R1] LDRH R3, [R1,#2] MVNS R2, RO LDRSB R4, [R1,#1] ! Register RO R1 R2 R3 R4 Content

If R1=0x00009300 and R2=0x00009000, evaluate the following program and determine th content of registers RO-R4 for the following program. Assume the processor access data in lit endian system LDR RO,=0×67983A5C STR RO, [R1] LDRH R3, [R1,#2] MVNS R2, RO LDRSB R4, [R1,#1] ! Register RO R1 R2 R3 R4 Content

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter4: Processor Technology And Architecture

Section: Chapter Questions

Problem 2PE: If a microprocessor has a cycle time of 0.5 nanoseconds, what’s the processor clock rate? If the...

See similar textbooks

Similar questions

Consider the following store instruction: SW R1, 0x000F(R0). Assume that the registers R0 and R1 are initialized with 0x00000001 and 0x53A78BC Frespectively. A section of the MIPS byte addressable data memory is shown. Give the memory word of the following memory locations after the SW operation: (a). 0x00000015. (b). 0x00000014. (c). 0x00000013. (d) 0x00000012.(e). 0x00000011. (f). 0x00000010.
Considering the following MIPS assembly code snippet. mydata: .word 0x01020304, 0x05060708, 0x090A0B0C0, 0x0D0E0F10, 0xE0001211, 0xA031023A … li $t1, 1 sll $t1, $t1, 2 lb $s0, mydata($t1) What is the value of register $s0 after the instruction lb was executed? _________ Please provide an answer and an explanation.
Consider the following portions of three different programs running at the same time on three processors in a symmetric multicore processor (SMP). Assume that before this code is run, Total is 15, val_1 is 45, val_2 is 25, and val_3 is 5. Core 1: Total = Total + val_1;Core 2: Total = Total - val_2;Core 3: Total = Total + val_3; 1. Show the assembly code for both instructions. Assume that Total, var_1, and var_2 are stored at 0x0100, 0x0120, and 0x0130 respectively.2. What are all the possible resulting values of Total? For each possibleoutcome, explain how we might arrive at those values. You will need to show all possible interleavings of instructions.3. How could you make the execution more deterministic so that only one set of values is possible?
The unique addresses assigned to the four registers (R11,R12,13,R14) of the I/O interface are equal to the XX3 , XX7 , XXB and XXF in Hex . Where XX is hex digits equal to your roll no . (if student is having roll no 45 than address are 453 ,457 ,45B , 45F in Hex ) .Show the well labeled external circuit that must be connected between and 12-bit I/O address from the CPU and the CS, RSI, and RS0 Inputs of the Interface.
Suppose we have the instruction Load 0000. Given memory and register R1 contain thevalues below:R130Memory Address Content0000 40...0010 30...0020 78...0030 55...0040 77...0050 84 Assuming R1 is implied in the indexed addressing mode, determine the actual value loaded into the accumulator using the following addressing modes: a. Immediateb. Directc. Indirectd. Indexed
3) The 8-bit register AR, BR, CR, and DR initially have the following values: [5]AR = 11010110; BR = 11100111; CR = 10110001; DR = 10111010Determine the 8-bit values in each register after the execution of the following sequenceof microoperations.AR  AR + BR Add BR + ARCR  CR AND DR, BR  BR + 1 AND DR to CR, Increment BRAR AR - CR Subtract CR from AR
in 80886 microprocessor Suppose that. DS = 0200H, BX = 0300H, and DI-400H Determine the memory address accessed by each of the following instructions, assuming real mode operation: (1) MOV AL,[1234H] (2) MOV AX,[BX] (3) MOV [DI]AL
Assume that registers $s0 and $s1 hold the values 0x90000000 and 0xA0000000, respectively. These are integer values. Please take into account that these are 32-bit registers. a) What is the value of $t0 after the following MIPS instruction has been completed? add $t0, $s0, $s1 $s0: 0 x 9 0 0 0 0 0 0 0 $s1: 0 x A 0 0 0 0 0 0 0
In each of the following MOV or MVN instruction, identify whether the use of the immediate value is VALID or INVALID. (a) MOV R1, #0xD017 (b) MOVW R1, #0xE689 (c) MOV R1, #0xAC5 (d) MVN R1, #0xAC5 (e) MVN R1, #996 (f) MVN R1, #0x9B000000 (g) MOV R1, #0xF300F300 (h) MOV R1, #0x1357CDEF
333: E8B3 8B3: 0A12 A12: 2153 Since the contents of the relevant addresses are 333 in the basic computer given above, the initial value of the PC is 333; When fetching and executing an indirectly addressing ISZ instruction, write the contents of the following registers in hexadecimal (hex) format for the T5 time. AR ........... DR......... IR ........... PC ........... SC ...........
Assume that the state of the 8088’s registers and memory just prior to the executionof each instruction in problem 15 is as follows: * in photos*What result is produced in the destination operand by executing instructions (a)through (k)? *only b,c,e,g* b) ADC SI, AX(c) INC BYTE PTR [0100H] (e) SBB DL, [0200H] (g) NEG BYTE PTR [DI]+0010H
. If R1 = 0xEF00DE12, R2 = 0x0456123F, R5 = 4, R6 = 28; Find the values of the destination registers for the following instruction? a) LSL R1, #8 b) ASR R1, R5 c) ROR R2, R6 d) LSR R2, #6 Substantiate your answers appropriately.