Task 2. Determine the absorption bands of caffeine(Which of the peaks gives auxochrome and which chromophore?/ What parts of the molecule are the bands associated with). Specify chromophores and auxochromes in the molecule((mark in the picture with different colors) 35000 30000 25000 20000 15000 10000 5000 200 A/ nm 250 300 Fig. 1.2-16 UV spectrum in ethanol Fig. 1.2-16 UV spectrum in ethanol CH3 H3C N' CH3 e/(cm2 mmol")

Task 2. Determine the absorption bands of caffeine(Which of the peaks gives auxochrome and which chromophore?/ What parts of the molecule are the bands associated with). Specify chromophores and auxochromes in the molecule((mark in the picture with different colors) 35000 30000 25000 20000 15000 10000 5000 200 A/ nm 250 300 Fig. 1.2-16 UV spectrum in ethanol Fig. 1.2-16 UV spectrum in ethanol CH3 H3C N' CH3 e/(cm2 mmol")

Organic Chemistry: A Guided Inquiry

2nd Edition

ISBN:9780618974122

Author:Andrei Straumanis

Publisher:Andrei Straumanis

ChapterL2: Mass Spectrometry

Section: Chapter Questions

Problem 24CTQ

See similar textbooks

Similar questions

Record your absorbance data for the YELLOW and RED dyes below. Calculate the dye concentration in mM for each cuvette using M1V2 = M2v2 . Remember the concentration of stock solutions (100^ % dye) is 0.020 mM(mM= millimolar =mm /L). Data for YELLOW: peak absorbance used on spectrophotometer =420nm Cuvette 1 - 100% dye = 0.680 absorption Cuvette 2 - 75% dye = 0.510 absorption Cuvette 3 - 50% dye = 0.340 absorption Cuvette 4 - 25% dye = 0.170 absorption Data for RED - peak absorption used on spectrophotometer = 500nm Cuvette 1 - 100% dye: 0.621 absorption Cuvette 2 - 75%: 0.466 absorption Cuvette 3 - 50% dye: 0.311 absorption Cuvette 4 - 25% dye: 0.1555 absorption
Hello, I am stumped on this problem. Calculate the amount of extract and amount of TE^-4 needed to get an aliquot of 1 ng/20 uL for the given quantitation result; 2.5 ng/20 uL. do I divide the 2.5 ng by the 20 uL before using c1v1=c2v2? Thank you for any help
fill in the column thats empty by finding the standard deviation for each average absorbance, with work please.
If the TLC plates had been developed in a more polar solvent, would retention factors on the whole be larger, smaller, or unchanged? Briefly (1 - 2 sentences) explain your reasoning
Why KBr used in IR spectroscopic sample preparation? Please shortly answer at your own words. Answer should be to the point (Specific 2-3 lines).
Table 1: Chromatography Results Mobile Phase: Distilled Water Solvent front distance (cm): 8 cm M&M Candy Separated Spot Color Migration Distance (cm) (distance to center of spot from origin) Red M&M Red 7.5 cm Green M&M Yellow 5.3 cm Blue 7.7 cm Blue M&M Blue 7.8 cm -please help with this part Calculations/Results: Table 1: Results with Distilled Water M&M Candy Separated Spot Color Rf Value Red M&M Green M&M Blue M&M Rf = Distance traveled by component in a given time/ Distance traveled by solvent in same time Show work with units for one sample calculation.
Calculate the Absorbance from concentration for each trial of 0,10, 30, 40, 50 % (with yellow LED) Absorbance=−log(Percent Transmittance/100) - did my best with transmission ruler, do the numbers look right
Please answer 1D. how would the Rf values change if eluted with hexanes using an alumina TLC plate? I think that an alumina plate is more polar than a silica plate, so I am inclined to say that this would increase the Rf values. But, I also know that hexanes are non-polar, so I am not sure if they would move up a very polar surface or not. Thanks!
With a resolution of 500 a peak will an m/z value of 297.000 from which of the following peaks? 297.439 297.603 297.356 298.000 297.232
Kindly help me annswer #5. response domain detection limit. The answer shouldbe 0.064. I don't know how to get it. Thank you.
Calculate the concentration of a solution of peptide AWSME, in mM if the absorbance at 280 nm for the solution is 0.6 absorbance units, and a 0.2-cm cuvette is used. For the extinction coefficient, take into account that e280(Trp) = 5690 M-1 cm-1 and e280(Tyr) = 1280 M-1 cm-1. Round your answer to two decimals.
What should be done if you got 2 identical Rf values for two samples?