In the calibration of a calorimeter, an electrical resistance heater supplies 100.0 J of heat and a temperature increase 0.850°C is observed. Then, 0.245g of a particular fuel is burned in this same calorimeter and the temperature increases by 5.23°C. Calculate the energy density of this fuel, which is the amount of energy liberated per gram of fuel burned.

In the calibration of a calorimeter, an electrical resistance heater supplies 100.0 J of heat and a temperature increase 0.850°C is observed. Then, 0.245g of a particular fuel is burned in this same calorimeter and the temperature increases by 5.23°C. Calculate the energy density of this fuel, which is the amount of energy liberated per gram of fuel burned.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter6: Thermochemistry

Section: Chapter Questions

Problem 112AE: In a bomb calorimeter, the reaction vessel is surrounded by water that must be added for each...

See similar textbooks

Similar questions

Microwave ovens convert radiation to energy. A microwave oven uses radiation with a wavelength of 12.5 cm. Assuming that all the energy from the radiation is converted to heat without loss, how many moles of photons are required to raise the temperature of a cup of water (350.0 g, specific heat =4.18J/gC) from 23.0C to 99.0C?
A sample of sucrose, C12H22O11, is contaminated by sodium chloride. When the contaminated sample is burned in a bomb calorimeter, sodium chloride does not burn. What is the percentage of sucrose in the sample if a temperature increase of 1.67C is observed when 3.000 g of the sample are burned in the calorimeter? Sucrose gives off 5.64103kJ/mol when burned. The heat capacity of the calorimeter and water is 22.51 kJ/C.
Nitrogen gas (2.75 L) is confined in a cylinder under constant atmospheric pressure (1.01 105 pascals). The volume of gas decreases to 2.10 L when 485 J of energy is transferred as heat to the surroundings. What is the change in internal energy of the gas?
In a bomb calorimeter, the reaction vessel is surrounded by water that must be added for each experiment. Since the amount of water is not constant from experiment to experiment, the mass of water must be measured in each case. The heat capacity of the calorimeter is broken down into two parts: the water and the calorimeter components. If a calorimeter contains 1.00 kg water and has a total heat capacity of 10.84 kJ/C, what is the heat capacity of the calorimeter components?
The complete combustion of acetylene, C2H2(g), produces 1300. kJ of energy per mole of acetylene consumed. How many grams of acetylene must be burned to produce enough heat to raise the temperature of 1.00 gal water by 10.0c if the process is 80.0% efficient? Assume the density of water is 1.00 g/cm3
Explain why absolute enthalpies and energies cannot be measured, and only changes can be determined.
A sample of nickel is heated to 99.8C and placed in a coffee-cup calorimeter containing 150.0 g water at 23.5C. After the metal cools, the final temperature of metal and water mixture is 25.0C. If the specific heat capacity of nickel is 0.444 J/C g, what mass of nickel was originally heated? Assume no heat loss to the surroundings.
Ethanol, C2H5OH, is used as a fuel for motor vehicles, particularly in Brazil. (a) Write the balanced equation for the combustion of ethanol to CO2(g) and H2O(g), and, using the data in Appendix G, calculate the enthalpy of combustion of 1 mole of ethanol. (b) The density of ethanol is 0.7893 g/mL. Calculate the enthalpy of combustion of exactly 1 L of ethanol. (c) Assuming that an automobile’s mileage is directly proportional to the heat of combustion of the fuel, calculate how much farther an automobile could be expected to travel on 1 L of gasoline than on 1 L of ethanol. Assume that gasoline has the heat of combustion and the density of n—octane, C8H18(Hf=208.4kJ/mol;density=0.7025g/mL).