In the tank-pipe-tank system given in the figure, water flows from A to C in horizontal pipes. Darcy friction factor in A-B pipe is 0.040, pipe diameter is 0.5m, pipe length is 1km and speed is 2m / s. Darcy friction factor in B-C pipe is 0.015. pipe diameter is 1.2m, pipe length is 20km. The gravitational acceleration is 9.81m/s2. There is no operational hydraulic head at point C. Which of the following is the minimum required vertical elevation between free water surfaces, H for running this system?

In the tank-pipe-tank system given in the figure, water flows from A to C in horizontal pipes. Darcy friction factor in A-B pipe is 0.040, pipe diameter is 0.5m, pipe length is 1km and speed is 2m / s. Darcy friction factor in B-C pipe is 0.015. pipe diameter is 1.2m, pipe length is 20km. The gravitational acceleration is 9.81m/s2. There is no operational hydraulic head at point C. Which of the following is the minimum required vertical elevation between free water surfaces, H for running this system?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cylindrical pipe with a cross-sectional radius r = 1.40[cm] is plunged into a l = 2.30[m] tall open water drum that is initially completely filled with water (pwater = 1000 [kg/m3]). The pipe goes h1 = 0.35 [m] above the drum before dropping down h2 = 3.50 [m] below the base of the drum as shown. The cross-sectional radius of the top side of the pipe is R = 2.20 [cm].A. How fast is the water going out of this pipe?B. What's the liquid's pressure at the top of the pipe? Assume that the system is exposed to 1.00 [atm] of air pressure.C. What's the maximum height the pipe can go above the drum before the water stops flowing out of the pipe? For liquid flow to be continuous, the liquid’s pressure must not fall before its vapor pressure. Assume that vapor pressure, in this case, is 2.30 [kPa].
Inside of a room, the atmospheric pressure measures out to be 100 kPa. A pipe with a diameter of 0.5 meters is used to release air into the surrounding atmosphere. The fan has a capacity of 2000 m3/h , consumes 1100 watts of power, and rotates at 1000 revolutions per minute. The pressure drop on the suction side is 60 pA, while the pressure drop on the discharge side is 80 kPa. When the operating speed is increased to 1200 revolutions per minute, calculate the fan's capacity based on the resulting change in power. in m3/s
A fan delivers 400 m3 /min of air at 1 atm and 21 C when rotating at 600 rpm, with a head of 8 cm WG. If the air temperature rises to 80 C with speed and air flow remains constant, determine the new back pressure in cm of water and the ratio of the new power required to the original power.
The impeller of a centrifugal blower has a radius of 15 cm and a blade width of 6.1 cm at the inlet, and a radius of 30 cm and a blade width of 3.4 cm at the outlet. The blower delivers atmospheric air at 20°C and 95 kPa. Disre- garding any losses and assuming the tangential components of air velocity at the inlet and the outlet to be equal to the impeller velocity at respective locations, determine the volu- metric flow rate of air when the rotational speed of the shaft is 800 rpm and the power consumption of the blower is 120 W. Also determine the normal components of velocity at the inlet and outlet of the impeller.
Here, air (105 kPa) at 37 degrees celcius is flowing upward in a 6cm diamater inclined duct, at a rate of 90 L/s. In this case the density of air is 1.1 kg/m3. The diameter of the duct reduces to 4cm through a reducer and a pressure charge occurs. This pressure change is measured by a water manometer. The elevation difference between the points where the two arms of the manometer are attached is 0.2 meters. What is the differential height between the fluid levels in the two manometer arms?
The liquid storage tank shown in Fig has two inlet streams with mass flow rates w1 and w2 and an exit stream withflow rate w3. The cylindrical tank is 2.5 m tall and 2 m in diam-eter. The liquid has a density of 800 kg/m. Normal operating procedure is to fill the tank until the liquid level reaches a nom-inal value of 1.75 m using constant flow rates:w1=120 kg/min, w2=100 kg/min, and w3=200 kg/min. At that point, inlet low rate w1 is adjusted so that the level remains constant.However, on this particular day, corrosion of the tank has opened up a hole in the wall at a height of 1 m, producing a leak whose volumetric flow rate q4(m3/min) can be approximated by q4=0.025√h−1 where h is height in meters.(a)If the tank was initially empty, how long did it take for theliquid level to reach the corrosion point?(b)If mass flow rates w1,w2,and w3 are kept constant indefi-nitely, will the tank eventually overflow? Justify your answer.
Air flows through a long duct of constant area at 0.15 kg/s. A short section of the duct is cooled by liquid nitrogen that surrounds the duct. The rate of heat loss in this section is 15.0 kJ/s from the air. The absolute pressure, temperature, and velocity entering the cooled section are 188 kPa, 440 K, and 210 m/s, respectively. At the outlet, the absolute pressure and temperature are 213 kPa and 351 K. Compute the duct cross-sectional area and the changes in enthalpy, internal energy, and entropy for this flow. Take C=1 KJ/KgK, C,-0.717 KJ/Kg.K
Air is kept in a tank at pressure Po = 689 KPa abs and temperature To = 17°C. If one allows the air to issue out in a one-dimensional isentropic flow, the flow per unit area at the exit of the nozzle where P = 101.325 KPa is Blank 1 kg/m2-s. For air, Use R = 287 J/kg-K and Mol. Wt. = 29.1 *Express your answers in whole significant figure without decimal value and without unit*
A cylindrical 125 cm high and 89 cm diameter, as given by the figurethe inside of the tank is initially completely filled with oil. Then 1.25 to the base edge of the tanka hole in diameter of cm is opened and the oil begins to drain from this hole. Oil output speed from tank(2gh)-1/2is given as. (h, the variable height of the oil inside the tank from the center of the holeand G indicates the acceleration of gravity). From the base of the oil level inside the tankCalculate the time it takes to fall to a height of 15 cm in [s].
Air is flowing through a horizontal variable area pipe at a constant rate of 0.03 m^3/s. Disregarding any frictional and compressibility effects, determine the pressure drop (delta P, in kPa) between two sections of diameters d1 = 6 cm and d2 = 3.25 cm. Take the air density to be 1.25 kg/m^3.
Water is flowing in a 5 cm diameter pipe at a velocity of 5 m/s. The pipe expands to a 10 cm diameter pipe. Calculate the pressure just after the expansion to a 10 cm diameter pipe if the prrssure in the 5 cm diameter pipe is 300 kPa. Friction is negligible. The specific weight of water is 9.81 kN/m³.A. 301.5 kPaB. 314.9 kPaC. 311.7 kPaD. 317.4 kPa
A hydroelectric power plant uses Pelton-type turbines, in which multiple nozzles are used to accelerate the waterwhich is directed onto the turbine blades, which are exposed to an atmospheric pressure of 101.325 kPa. The water enters the nozzles with an absolute pressure of 500 kPa and a speed of 5 m/s, and the nozzle outlets are exposed to atmospheric pressure and have an internal diameter of 5 cm. Consider that the specific mass of water is 1,000 kg/m3. Determine the mass flow rate of water through each of the nozzles, and explain why the actual mass flow rate will be lower.