X,X,R,4(1)R,X_Fig. Equivalent Circuit of IMLest's consider three phase, Y connected, 220 volt(line to line), 7.5 kW, 75 Hz, four pole IM has the following parametervalues in /phase referred to the stator:R1 = 0.294 2, R2 = 0.144 N, X1 = 0.503 N, X2 = 0.209 N, Xm = 13.25 NDetermine the following for 0.015 slipa) Electromechanical Torque (Tmech), Electromechanical power (Pmech)b) Maximum electromechanical torque (T,maz), Corresponding speed (n, maz)C) Electromechanical statrting torque (Tstart), Corresponding stator load current (I, start)a. Tmech = 15.2537 N. m, Pmech = 4353.62 W, n maz = 925.793 rpm, Tmaz = 220.437 N. m, I2 start = 115.562 A,b. Тпеch — 15.4105 N.m, Pmech4872.83 W, n,maz825.827 rpm, Tmaz = 154.758 N. m, I2start = 145.657 A,c. Tmech = 18.6764 N. m, Pmech4334.51 W, n,maz = 1818.42 rpm, Tmaz = 93.101 N. m, I2 start = 150.265 A, 1d. Tmech13.3705 N. m, Рпеch4293.87 W, n,maz950.539 грт, Tmаz153.768 N. m, I2start = 175.257 A,e. Tmech15.4105 N. m, Pmech4933.77 W, n,maz919.728 rpm, Tmaz = 154.791 N. m, I2 start = 125.567 A,%3D

Answered: Image /qna-images/answer/9f0184a7-b29f-4976-a578-76dbf052e663.jpg

Lest's consider three phase, Y connected, 220 volt(line to line), 7.5 kW, 75 Hz, four pole IM has the following parameter values in /phase referred to the stator: R = 0.294 N, R2 = 0.144 N, X1 = 0.503 N, X2 = 0.209 N, Xm = 13.25 N Determine the following for 0.015 slip a) Electromechanical Torque (Tmech), Electromechanical power (Pnech) b) Maximum electromechanical torque (Tmaz), Corresponding speed (n, maz) c) Electromechanical statrting torque (Tastart), Corresponding stator load current (I2 start)

Lest's consider three phase, Y connected, 220 volt(line to line), 7.5 kW, 75 Hz, four pole IM has the following parameter values in /phase referred to the stator: R = 0.294 N, R2 = 0.144 N, X1 = 0.503 N, X2 = 0.209 N, Xm = 13.25 N Determine the following for 0.015 slip a) Electromechanical Torque (Tmech), Electromechanical power (Pnech) b) Maximum electromechanical torque (Tmaz), Corresponding speed (n, maz) c) Electromechanical statrting torque (Tastart), Corresponding stator load current (I2 start)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What is Mesh Analysis and when is it effective to use? What is Nodal Analysis and when is it effective to use? How was superposition theorem derived? What were the factors they've considered?
Distribution systems have different levels of customer service, whether they are Industrial, Commercial or Residential. In the distribution is where the energy measurements of the consumers and billing. Consumer billing is differentiated by the type of consumer and the level of tension that he is connected to the distribution system. a) Explain what the binomial tariff is, and which installment is paid by residential consumers? b) What are the current tariff flags, and for what purpose were they created?
For the serial-parallel network of the next picture: a. Determine the total impedence ZT and the admitance YT.b. Determine the currents I1, I2 and I3.c. To check the Kirchhoff's Law showing that Is = I1+I2+I3.d. Determine the potency factor of the network, Which is the potency? (advance or of retardation)
The single line diagram of a small power system isshown in Fig. 1. The corresponding reactancediagram, with reactances in per unit, is shown inFig. 2. A generator with emf equal to 1.25∠0° perunit is connected through a transformer to highvoltage node 3, while a motor with internalvoltage equal to 0.85∠ − 45° per unit is similarlyconnected to node 4. Develop the nodaladmittance matrix for each of the networkbranches and then write the nodal admittanceequations of the system.
4. A LRT car, 5km distance from the Tayuman, takes 100A over a 100 mm hard drawn copper trolley wire having a resistance of 0.270 ohm per km. The rail and ground return has a resistance of 0.06 ohm per km. If the station voltage 750V, What is the voltage of the car?
Suppose a power system consists of two isolated regions: a western region and an eastern region. Five units have been committed to supply 3090 MW as shown below. The two systems are separated by a transmission line that can handle a maximum transfer of 550 MW in either direction. Calculate the spinning reserve for the overall system and for eachregion.
In an industrial application in which a conveyor belt with dimensions of 5m long by 2m wide, must transport packages of cement. The plant is known to be located on the Caribbean coast; in addition to the dimensions (d=80mm), the material (4140) and the speed at which the axis works (30 RPM). Select a motor that meets the requirements requested for the operation of the system, also includes the IP protection that the motor must have. Can it be connected directly?
Type your question here The system shown in fig. below is an alternative to the one shown in fig. of Q3 for sending two messages on one carrier. (a) If f(t) = cosw,t and f,(t) = cosw,t derive an expression for (t). %D (b) Devise block diagram for suitable demodulator
Note: Answer the question by Poles and Zeros of the System "Function H(z)" & Comments on System Causality and Stability. Also, please explain the answer with the drawing.
Describe the state estimation process in power systems. How does it use measurements from various sensors to estimate the current state of the network and detect any anomalies or errors?
It’s amazing! Zainab exclaimed and asked: How is it possible for a person to speak at a radio station in Tema for me to hear it at my house in Madina, ‘just’ by using this small device (i.e., through an FM tuner)?" You a required to respond to Zainab’s question. In your explanation to Zainab, use the relevant block diagrams to demystify the principles of operations that are responsible for this. Note that Tema and Madina are geographically apart by a distance of about 33 kilometres.
Good day! Please help me find the g-parameters. Thank you!