Linear momentum) Water flows through a right-angle valve at the rate of 1010 lbm/s, as is shown in the figure below. The pressure just upstream of the valve is 94.8 psi, and the pressure drop across the valve is 53.0 psi. The inside diameters of the valve inlet and exit pipes are 12 and 24 in. If the flow through the valve occurs in a horizontal plane, determine the (a) x and (b) y components of the force exerted by the valve on the water. 12 in. 24 in. Valve (a) Ib (b)

Linear momentum) Water flows through a right-angle valve at the rate of 1010 lbm/s, as is shown in the figure below. The pressure just upstream of the valve is 94.8 psi, and the pressure drop across the valve is 53.0 psi. The inside diameters of the valve inlet and exit pipes are 12 and 24 in. If the flow through the valve occurs in a horizontal plane, determine the (a) x and (b) y components of the force exerted by the valve on the water. 12 in. 24 in. Valve (a) Ib (b)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water enters vertically and steadily at a rate of 35 L/s into the sprinkler shown, with unequal arms and unequal discharge areas. The smaller jet has a discharge area of 3 cm2 and a normal distance of 50 cm from the axis of rotation. The larger jet has a discharge area of 5 cm2 and a normal distance of 35 cm from the axis of rotation. Disregarding any frictional effects, determine (a) the rotational speed of the sprinkler in rpm and (b) the torque required to prevent the sprinkler from rotating.
Neglecting head losses, determinewhat horsepower the pump must deliver toproduce the flow as shown. Here theelevations at points A, B, C, and D are 110 ft.200 ft, 110 ft and 90 ft, respectively. The nozzle area is 0.10 ft2
The pipe elbow below discharges water at rate of SN/100 (m3/s) into the atmosphere at section 2. The total volume of the passage between sections 1 and 2 is equal to 0.2 m3 and the total mass of the elbow material between sections 1 and 2 is equal to 10 x SN (kg). Neglect any friction losses. Calculate the horizontal and vertical forces acting on the elbow. Also, calculate the resultant force and angle of force on the elbow. ****SN=21
The jet of water of a pelton wheel is 80mm diameter. The jet strike's the bucket on the tangential line 0.45m from the centre of the wheel and the jet is deflected through 160° while it is moving across the bucket. Ignore friction and determine the power and hydraulic efficiency if the speed is 275 r/min and the pressure behind the nozzle is 680kPa
The jet of water that spews out from the reservoir inti the open air hits the concrete block and is divided into two equal arms. Orifice cross section area at point 1 is A1= 150 cm^2. Neglecting friction losses, a) Find the flow rate (Q1) in section 1. b) Find the intensity of the reaction force (R) that will occur in the concrete block and its angle with the horizontal. (h=3.5 meters, pWater= 1 ton/m^3, yWater= 9.81kN/m^3, g= 9.81 m/s^2, angle a= 45 degree)
A horizontal nozzle discharges water into the atmosphere as shown in the figure. the relative pressure at point 1 equal to ?1 = 18 ??? . A. A Pitot tube connected to a mercury manometer is inserted into the flow. in the area section A1 indicating a height difference ℎ = 0.01 m. For this reading indicated in the Pitot tube, determine the velocity in the A1 area section of the nozzle. B. For the dimensioning of the anchor block it is necessary to determine the force that the nozzle applies over the fluid. Calculate the component of this force in the x direction. Data: ?1 = 0.070 ?; ?2 = 0.060 ?; ? = 30°; ??? = 13.6
Water is flowing through a U-section pipe as shown in Figure 1.2. At flange (1) the total absolute pressure is 240 kPa, and water flows into the pipe at 42 kg/s. At flange (2), the total pressure measured is 190 kPa with a flow rate of32 kg/s. At point (3) water discharges into the atmosphere at 90 kPa at a flowrate of 10 kg/s. The mass of the elbow and the water in it is 50 kg. Neglecting the momentum-flux correction factor, determine the net x- and z-force at the two flanges connecting the pipe.
For the system shown below, calculate the vertical distance (in meters) between the surfaces of the two reservoirs when water at 10°C flows from A to B at the rate of 0.03 m3/s. The elbows are standard. The inlet is inward projecting, and the exit is square edged. The total length of the 4-in pipe is 94 m. For the 6-in pipe it is 274 m.
jet of water of diameter 100 mm strikes a curved plate at its center with a velocity of 15 m/s. The curved plate is moving with a velocity of 7 m/s in the direction of the jet. The jet is deflected through an angle of 150°. Assuming the plate smooth find: (i) Force exerted on the plate in the direction of the jet. (ii) Power of the jet, and (iii) Efficiency.
Water enters a rotating lawn sprinkler at a steady rate of 16 gal/min. The exit cross-sectional area of each of the two nozzles is 0.04 in2 and the flow leaving is tangential. The radius from the axis of rotation to the centerline of each nozzle is 8 in. (a) determine the resisting torque required to hold the sprinkler head stationary (b) determine the resisting torque associated with a sprinkler rotating at a constant 500 rpm (c) determine the angular velocity of the sprinkler if there is no resisting torque (ans: (a) 2.96 ftlb (b) 1.35 ftlb (c) 920 RPM
Water enters a two-armed lawn sprinkler along the vertical axis at a rate of 150 L/s, and leaves the sprinkler nozzles as 2cm diameter jets at an angle of u from the tangential direction. The length of each sprinkler arm is 0.52 m. Disregarding any frictional effects, determine (a) Angular momentum and (b) the rate of rotation n of the sprinkler in rev/min For ϴ = 30°
In the dam shown in the figure, the water flows at the entrance of the conduitwith a speed of 0.4 m/s and exits at 9.5 m/s the generator building, 175 m belowof the socket Considering that the temperature of the water in the dam is 28 °C andthat the gravitational acceleration of the place is 9.78 m/s2 , determine:a) The pressure difference between the outlet and the inlet of the intake.b) The diameter of the duct at the outlet connected to the generator building, if theinput area in the socket is 0.7 m2. .