External Problem 2: Linear Momentum and Bernoulli Equations The double nozzle in the figure below discharges water at A and B into the atmosphere at a rate of 0.5 m'/s. The nozzle is lying in a horizontal plane. Assume steady and frictionless flow and the water speed in each jet (4 and B) to be the same. Jet A is 10 cm in diameter, jet B is 12 cm in diameter, and the pipe inlet is 30 cm in diameter. (p - 1000 kg/m'). a) Applying Bernoulli's equation between the inlet section and any of the outlet sections, show that the pressure at section 1 is 315 612 Pa gage; b) What force acting through the flange bolt is required to hold the nozzle in place? B A - Flange

External Problem 2: Linear Momentum and Bernoulli Equations The double nozzle in the figure below discharges water at A and B into the atmosphere at a rate of 0.5 m'/s. The nozzle is lying in a horizontal plane. Assume steady and frictionless flow and the water speed in each jet (4 and B) to be the same. Jet A is 10 cm in diameter, jet B is 12 cm in diameter, and the pipe inlet is 30 cm in diameter. (p - 1000 kg/m'). a) Applying Bernoulli's equation between the inlet section and any of the outlet sections, show that the pressure at section 1 is 315 612 Pa gage; b) What force acting through the flange bolt is required to hold the nozzle in place? B A - Flange

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The mean radius of an axial flow reaction turbine is 2.6 ft. and the axial velocityis 25 ft./s. The wicket gates are turned at an angle such that relative velocity at theinlet flow makes an angle of -45° with the blade velocity. The wheel and hub radiiare 3.6 ft. and 1.6 ft., respectively. The turbine rotates at 240 rpm. If water leaves theblade in a purely axial direction, calculate H and all relevant angles.Ans: H=81.87 ft.; α1=31.8°; β2=20.93°
A simple carburetor under a certain condition delivers 5.45 kg/h of petrol with an air fuel ratio of 15. The fuel jet area is 2mm2 with coefficient of discharge of 0.75. If the tip of the fuel jet is 0.635cm above the level of petrol in the float chamber and the venturi throat coefficient of discharge of 0.80. calculate: (i) The venturi depression in cm of H2O necessary to cause air and fuel flow at the desired rate. (ii) The venturi throat diameter. (iii) The velocity of air across the venturi throat. You make take density of air = 1.29 kg/m3 and specific gravity of petrol =0.72
The axial flow pump produces a discharge of 0.095 m3/sm3/s. (Figure 1) The impeller is rotating at ω� = 80 rad/srad/s, and it has a mean radius of 75 mmmm. The diameter of the impeller's shaft is 100 mmmm. Determine the angle α2�2, which the velocity of the water as it exits the blades V2�2 makes with its tangential component Vt2��2. Express your answer using three significant figures.
1) Interpret solar power in the context of environmental impact.2. What is the rigid dichotomy between windmill and diesel-driven pumps?3. For a normal windmill-driven pump at 3 m/s wind speed, the yield at a 10 m Head is typically 0.12 liters/s per m2 of rotor area, value windmills in the context of yield.
[5] A Francis turbine operates at its maximum efficiency point at h0 = 0.94, corresponding to a power specific speed of 0.9 rad. The effective head across the turbine is 160 m and the speed required for electrical generation is 750 rev/min. The runner tip speed is 0.7 times the spouting velocity, the absolute flow angle at runner entry is 70 deg from the radial direction and the absolute flow at runner exit is without swirl. Assuming there are no losses in the guide vanes and the mechanical efficiency is 100%, determine (i) the turbine power and the volume flow rate; (ii) the runner diameter; (iii) the magnitude of the tangential component of the absolute velocity at runner inlet; (iv) the axial length of the runner vanes at inlet.
The external and internal diameters of the inward flow reaction turbine 60 cm and 30 cm, the width of the inlet are 15 cm. The flow velocity through the runner is constant throughout and is equal to 1.5 m/s. Calculate discharge and the width at the outlet if 8% of the circumferential area is occupied by the blade thickness at both inlet and exit.
A centrifugal pump delivers 25 liters of water per second against a head of 10 meters and running at 1300 rpm requires 10 kW of power. Determine the discharge, head of the pump and power required if the pump runs at 1500 rpm. (Ans. 0.0288cumec or 1.73 cu.m./min , 13.31m, 15.36kw)
A pump draws water from a 20 cm diam suction pipe and discharges through a 15 cm diam pipe in which the velocity is 3.60 m/s. The pressure is - 34. 465 kPa at A in the suction pipe. The 15 cm diam pipe discharges horizontally into air at C. To what height h above B can the water be raised if B is 1.8 m. above A and 20 hp is delivered to the pump? Assume that the pump operates at 80% efficiency and that the frictional loss in the pipe between A and C is 3 m.Determine the inclination angle at point C for the water stream to reach a range of 10 m. Also calculate the maximum height that the water can go from the selected datum plane.
An inward flow reaction turbine has external and internal diameters as 1.095 m and 0.553 m respectively. The turbine is running at 210 R. P. M. The velocity of flow through the runner remains constant and is equal to 2.0 m/s. The width of the turbine at inlet is 241 mm. The guide blades make an angle of 10.5oto the tangent of the wheel. If the discharge of the turbine at the outlet is radial determine the following:i) Draw the inlet and outlet velocity diagramsii) The absolute velocity of the water at the inlet of the runner.iii) The velocity of whirl at inletiv) The relative velocity at inletv) The runner blade anglesvi) Width of the runner at outletvii)The hydraulic efficiency of the turbine
A Francis radial-flow hydroturbine has the following dimensions, where location 2 is the inlet and location 1 is the outlet: r2 = 6.60 ft, r1 = 4.40 ft, b2 = 2.60 ft, and b1 = 7.20 ft. The runner blade angles are ?2 = 82° and ?1 = 46° at the turbine inlet and outlet, respectively. The runner rotates at n. = 120 rpm. The volume flow rate at design conditions is 4.70 ×106 gpm. Irreversible losses are neglected in this preliminary analysis. Calculate the angle ?2 through which the wicket gates should turn the flow, where ?2 is measured from the radial direction at the runner inlet. Calculate the swirl angle ?1, where ?1 is measured from the radial direction at the runner outlet. Does this turbine have forward or reverse swirl? Predict the power output (hp) and required net head (ft).
A pump draws water from a 20 cm diam suction pipe and discharges through a15 cm diam pipe in which the velocity is 3.60 m/s. The pressure is – 34. 465 kPaat A in the suction pipe. The 15 cm diam pipe discharges horizontally into air atC. To what height h above B can the water be raised if B is 1.8 m. above A and20 hp is delivered to the pump? Assume that the pump operates at 80 %efficiency and that the frictional loss in the pipe between A and C is 3 m. Determine the inclination angle at point C for the water stream to reach a range of 10 m. Calculate the maximum height that the water can go from the selected datum plane.
Using the situation below, how would I determine the net resultant force exerted on the reducer by the water? In this situation, water is flowing horizontally in a pipe that has a diameter of 25cm. This water is flowing at 8 m/s and at 300 kPa gage it enters a 90 degree bend reducing section. This bend reducing section is connected to a vertical pipe that has a diamater of 15cm. Moreover, the inlet of the bend is 45 cm above the exit. Here, fricition and gravity are negligible and the momentum flux correction factor is 1.04.