Match each of the following symbols to the phrase that describes it. Answers are used only once. 32 1. 03V 2. 8 3. 500 Sampling length pecified. 0.4 4. Minimum material to be removed is specified. 250/05 5. Rough machine finish. LAP 64 6. Specified as micrometers. 7. 125 Very-fine machine finish 8. 125 9 64 10, 63 32

Match each of the following symbols to the phrase that describes it. Answers are used only once. 32 1. 03V 2. 8 3. 500 Sampling length pecified. 0.4 4. Minimum material to be removed is specified. 250/05 5. Rough machine finish. LAP 64 6. Specified as micrometers. 7. 125 Very-fine machine finish 8. 125 9 64 10, 63 32

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The following limits are specified in a limit system, to give a clearance fit between a hole and a shaft: Hole = 10 (+0.05 )/(-0.00 ) mm and Shaft = 10 (-0.003)/(-0.010) mm. Determine the basic size, tolerance and allowance, maximum and minimum clearances, type of fit.
In a limit system, the following limits are specified for a hole and shaft assembly: Hole = 70 (+0.04 )/(+0.00 ) mm and Shaft = 70 (-0.04)/(-0.08) mm. Determine the basic size, tolerance and allowance, maximum and minimum clearances, type of fit.
Tolerances for a hole and shaft assembly having a nominal size of 50 mm are as follows: Hole = 50 (+0.02 )/(+0.00 ) mm and Shaft = 50 (-0.05)/(-0.08) mm. Determine the basic size, tolerance and allowance, maximum and minimum clearances, type of fit.
A 150.00-mm sine bar is used to inspect a part angle that has a dimension of 35.0° ± 1.0°. The sine bar rolls have a diameter = 25.0 mm. A set of gage blocks is available that can form any height from 10.0000 mm to 199.995 mm in increments of 0.005 mm. All inspection is performed on a surface plate. Determine (a) the height of the gage block stack to inspect the minimum angle, (b) the height of the gage block stack to inspect the maximum angle, and (c) the smallest increment of angle that can be set up at the nominal angle size
A 30 mm diameter hole is made on a turret lathe tothe limits, 30.035 and 30.00. The followingtwo grades of shafts are used to fit in the hole:(a) φ29.955mm and 29.925mm, and (b) φ30.055mm and30.050mm.Calculate the maximum tolerance, clearance and indicatethe type of fit in each case by a sketch.ii) Suggest suitable fits and their letter and tolerancegrades for the components
Round off to 3 significant figures, and the tolerance is ±1 in the 3rd significant digit. Thank you.
Some hole size tolerances are specified as D7, N6, and H8. Where does the print reader find the values for those specifications? (Multiple Choice)a. In a tolerance block located in the upper-left corner of the sheetb. On line at the manufacturers websitec. A supplemental documentd. The are proprietary and not stated
1. Calculate the tolerances and allowances for a shaft with a diameter of 40 mm with a tolerance area k and a tolerance quality number 6, paired with a hole of the same diameter as the shaft and a tolerance area H with a tolerance quality 7. Also draw these tolerances schematically. ( answer in 20 minutes very needed thank u )
Answer is 14.00714 rad/s. Please provide a solution.
Please help me answer this correctly. Please write the solution on paper. Thank you. Note: The tolerance is ± 1 in the third significant digit.
I need help with numbers 4 and 7.They are both wrong. One the part attached what is the maximum variation in parallelism with only the profile applied?What can you expect the flatness tolerance to be on the top surface? Please refer to attached image.
by solving with shearing and bearing stress method my last 2 digites of my ID (54)