Most iron (III) compounds are very weakly colored, and do not lend themselves well to visible spectrometric analysis. What is one possible reliable way to improve the analysis? Group of answer choices: Find a different way to analyze the sample Use a larger sample Complex the iron with another chemical to increase its absorbance Analyze something else

Most iron (III) compounds are very weakly colored, and do not lend themselves well to visible spectrometric analysis. What is one possible reliable way to improve the analysis? Group of answer choices: Find a different way to analyze the sample Use a larger sample Complex the iron with another chemical to increase its absorbance Analyze something else

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter26: Molecular Absorption Spectrometry

Section: Chapter Questions

Problem 26.1QAP

See similar textbooks

Similar questions

In determining the concentration of a sample X, it was found that it has maximum absorbance at 275 nm. Compound X, has molar absorptivity at 275 nm of 8400 L / mol.cm. Using a spectrophotometer with a 1 cm cuvette, an absorbance of 0.70 was found. What is the concentration of compound X in the sample?
Monomer-dimer formation can affect the absorbance measurements using Beer’s law, it is an example of: A. chemical deviation B. instrumental deviation C. real deviation D. instrumental deviation
You have two solutions of the same compound that are blue. one is very pale and the other is very intense. Absorbance of each solution was measured with a spectrophotometer at the same wave length at which the solution absorbs. (A) Which solution has the higher absorbance? (B) Which is the more concentrated solution?
If the measured absorbance at 280 nm of the protein in a 1.00-cm cuvette = 0.564, what is the extinction coefficient at this wavelength?
A student prepared a sample of Molecule VeryRed at 59.0 MM, and measured with the absorbance at 550 nm with a path length of 0.760 cm. The measured absorbance was 0.451 after subtracting the blank. Calculate the molar absorptivity of Molecule VeryRed (in M-1 cm-1).
Maria was tasked to determine the concentration of a Fe2(SO4)3 solution. She prepared 5 different standards of Fe2(SO4)3 using the table below as her guide. She ran the standards and the unknown solution through UV-VIS spectroscopy and recorded the absorbances of each solution. What is the concentration of the unknown solution? 0.188 M 0.296 M 0.749 M 0.857 M
A compound has an extinction coefficient of 22,150 M-1 cm-1. If a solution of this compound has an absorbance of 0.6 in a 1.15 cm cuvette, what is the concentration of the solution?
In spectophotometry, what should be done if there is a greater absorbance reading than the most concentrated solution?
Topic: Transmittance and absorbance, lambert-beer law To determine the content of Cu in a sample, 0.3632 g are weighed, dissolved with 80 ml of acid and brought to a volume of 250 ml, the absorbance of the solution is measured together with a series of standards in cells of 1 cm and the data obtained were: ppm Cu 0 2 4 10 12 Absorbance 0 0.082 0.164 0.410 0.440 The absorbance of the sample was 0.125. Calculate the mg of Cu in 100 g of sample
A standard containing 20 mg/mL of compound P is placed in a 1 cm cuvette. The absorbance of the standard is 1.20 at 600 nm. A sample containing Compound P has an absorbance of 0.50. What is the concentration of this sample?
When we perform Bradford Assay to measure protein concentration, the spectrophotometer is set 595 nm because: a. the excitation peak of Coomassie Blue is best observed at 595 nm b. when Coomassie Blue binds to proteins, its maximum absorbance shifts to 595 nm c. the reducing effects of Coomassie Blue shifts the protein's maximum absorbance to 595 nm d. myoglobin is best observed at 595 nm
Fluorometry is more selective and more sensitive than absorption spectrometry.Tell what is meant by selectivity and sensitivity.