You have prepared several dilutions of a standard compound. You measure the absorbance of each solution at 340 nm using a 1 cm cuvette and your results are listed in the table below. Determine the concentration of an unknown sample with an absorbance of 0.085 at 340 nm. Concentration (uM) Absorbance at 340 nm 0.009 4. 0.020 8. 0.061 16 0.111 32 0.189

You have prepared several dilutions of a standard compound. You measure the absorbance of each solution at 340 nm using a 1 cm cuvette and your results are listed in the table below. Determine the concentration of an unknown sample with an absorbance of 0.085 at 340 nm. Concentration (uM) Absorbance at 340 nm 0.009 4. 0.020 8. 0.061 16 0.111 32 0.189

Chemistry & Chemical Reactivity

9th Edition

ISBN:9781133949640

Author:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Publisher:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Chapter4: Stoichiometry: Quantitative Information About Chemical Reactions

Section4.8: Stoichiometry Of Reactions In Aqueous Solution-titrations

Problem 2RC

See similar textbooks

Similar questions

For A crystal violet hydroxide lab, The procedure requires to set the wavelength at 595 nm. Why do you need to measure the absorbance at this wavelength? Based on this, will the absorbance increase or decrease over time?
Sample (μg) Absorbances (520 nm) Concentration 0.0 0.621 0 2.5 0.599 2.5 5.0 0.556 5 10.0 0.469 10 15.0 0.418 15 20.0 0.291 20 Plot a graph in which y axis represents for absorbance and x-axis represents for concentration From graph, y=mx + c Calculate the vitamin C concentrations of samples by the equation with consideration of dilution factors.
Determine the concentration of your prepared Iron (III) Salicylate Dianion solution (pure ASA) in the 10.0 mL of 1.0 M NaOH in mg/mL (Part D) using Beer's Law plot. Hint:You need to use the measured absorbance reading of your prepared Iron (III) dianion (absorbance reading: 0.83). Information from the plot: Standard: Concentration ofASA in Standards (mg/mL) A: 0.18 B: 0.14 C: 0.10 D: 0.070 E: 0.040 Mass of salicylic acid (g) 0.17g Volume of acetic anhydride (mL) 0.34mL Mass of filter paper (g) 0.35gMass of "impure" ASA and filter paper (g) 0.49g Mass of prepared "impure" ASA (g) 0.14g Melting point range of prepared ASA (°C) 20.9 °C Melting point range of standardASA (°C) 18.5°C Percent purity: 28.57% Percentage yield: 66.7% Chemical equation: C7H6O3 + C4H6O3pure ASA knowing that two consecutive dilutions were done to prepare the solution. Show all of your work.C9H8O4 + C2H4O2 b) Then, calculate the mass (in mg) of
The nickel level in a soil sample was determined using AAS. A 3.0 g sample was dissolved in acid and then diluted to a total volume of 100.0 mL. The absorbance of this solution determined at a wavelength of 232 nm, was found to be0.3. Several standard solutions were tested under the same conditions and a calibration curve shown below was obtained. Calculate the mass of nickel in mg.
Complete the information on these tables: wavelength 470 nm conc Um absorbance % transmission 700 0.45 35.58% 500 0.32 47.78% 300 0.19 64.2% 100 0.06 86.23% wavelength 502 nm conc Um absorbance % transmission 700 1.08 8.37% 500 0.77 16.99% 300 0.46 34.57% 100 0.15 70.15% Which mathematical relationship is most useful to relate concentration to the amount of light passing through the solution? (% Transmission, or Absorbance), Why? How does the slope of the absorbance/concentration graph vary with wavelength? Is there an “optimum” wavelength for your KMnO4 sample?
Solutions that contain the FeSCN2+ ion are blood red (you will see this at the end of the second quarter of lab). Consider the regions of the visible spectrum in which the compound should absorb light and prepare a rough sketch of absorbance vs. wavelength for each solution. Label λ max on the graph. (Is this question asking for the graph of my data at the end)
Solution. Vol. of A solution (mL) [methyl red], M Absorbance 1 10.00 _1.64 x10^-16_ _0.256_ 2 15.00 _2.45 x10^-16_. _0.373_ 3 20.00 _3.27 x10^-16_. _0.486_ 4 25.00 _4.09 x10^-16_. _0.620_ Plot a graph of the absorbance (y axis) as a function of the concentration of methyl red (x axis). What is the slope of the graph?
A standard curve of absorbance vs. concentration has a linear trendline of y = 0.56x + 0.987. Use this trendline to calculate the concentration of an unknown sample that has an absorbance of 1.245.
The equation of your standard curve of absorbance versus concentration (mM) is y = 1.245x + 0.0012. You put a solution of unknown concentration into the Spec20 and get an absorbance value of 0.227, which lies within the standards used to make the standard curve. What is the concentration of the unknown solution in mM?
If a solution has an absorbance of 2 you can be certain that the solution is highly diluted and needs to be concentrated all the statements are correct this is a reliable absorbance and downstream analysis can be done the solution is highly concentrated and needs dilution
Using the given data compute for the sodium concentration of the patient. Use the same formula in the computation of the concentration using absorbance and concentration of the standard. Standard Absorbance : 0.112 Concentration : 150mmol/L Patient Serum Sample: Absorbance : 0.266 Concentration : ??
In a pharmaceutical industry a drug Paracetamol (151.163 g/mol) is determined in a sample. A 0.0315 g samples was reacted with methanol and diluted the solution to 1 L. the solution λ max at 243 nm (ε=2.6×104 cm-1 mol-1 L). The solution exhibits an absorbance of 0.642 in a 2 cm cell. Calculate the percentage paracetamol in the sample.