None Air is flowing steadily in an insulated duct. The pressure andgiven belowtemperature measurements of the air at two stations A and B are0.287where p, v, and T areheat c, is constant at 1.005 kJ/kg K, h = c, T, andT%3D%3Dpressure (in kPa), volume (in m'/kg) and temperature (in K) respectively.Station BStation APressure130 kPa50°C100 kPa13°CTemperature

Entropy is the measure of disorderness of any system. If heat flow occurs through any system, then…

O Air is flowing steadily in an insulated duct. The pressure and given below temperature measurements of the air at two stations A andB are 0.287 heat c, is constant at 1.005 kJ/kg K, h = c, T, and T where р, т, аnd T are %3D - %3D pressure (in kPa), volume (in m’/kg) and temperature (in K) respectively. Station A Station B Pressure Temperature 130 kPa 50°C 100 kPa 13°C

O Air is flowing steadily in an insulated duct. The pressure and given below temperature measurements of the air at two stations A andB are 0.287 heat c, is constant at 1.005 kJ/kg K, h = c, T, and T where р, т, аnd T are %3D - %3D pressure (in kPa), volume (in m’/kg) and temperature (in K) respectively. Station A Station B Pressure Temperature 130 kPa 50°C 100 kPa 13°C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 0.2 m3 vessel contains 1265 kg of water at 90 ⁰C. Determine pressure, specific and total internal energy, specific and total enthalpy, and specific and total entropy
Air flows steadily in a pipe at 300 kPa, 77°C, and 25 m/s at a rate of 18 kg/min (Fig. 5–17). Determine (a) the diameter of the pipe, (b) the rate of flow energy, (c) the rate of energy transport by mass, and (d) the error involved in part c if the kinetic energy is neglected.
Air flows into a turbine at a rate 30 [m 3 /s], a temperature of 1100 [K] anda pressure of 300 [kPa]. The turbine’s work output is 200 [kJ/kg]. Determine thetemperature of the air at the exit, the power output in [kW] and the isentropicefficiency. The pressure ratio of the turbine is 3. The specific gas constant, R, for airis 0.287 [kJ/kg-K].
An ideal gas at 20 °C and 1.2 atm enters a pipe with an internal diameter of 4.5 inches. The average velocity at the entrance is 3.4 m/s, and the gas exits the pipe at 6.2 m/s and into the atmosphere, at 15 °C. Determine the diameter of the pipe at the exit.
In a condenser, vacuum is 720mm of Hg when the barometer reads 760mm. Mean temperature of condensate is 32°C. Exhaust steam coming to condenser is 45,000 kg per hour and its dryness fraction is 0.9. Determine the quantity of cooling water, in kg/min, required if the temperature rise of cooling water is 12°C.
A fan is used to transport CO2 gas (MW = 44 g/mol) gas at rest @ 700mmHg. At the discharge end, the pressure is 765mmHg, and the velocity is 100 m/s. Assuming the flue gas behaves ideally, and the process is isothermal, with the temperature maintained at 100C. Determine the theo. power required to move 45000 m /h of the flue gas.
A 2.18 kg of air at 22.89 C underwent an isobaric process wherein its initial volume of 1.64 m3 was doubled. Determine the change in entropy (kJ/K) of the system. Consider the individual gas constant, specific heat at constant pressure, and specific heat ratio of air as 0.287 kJ/kg-K, 1.00 kJ/kg-K, and 1.4 respectively.
Helium expands polytropically steadily through a turbine according to the process pV1.5=C. The inlet temperature is 1000°K, inlet pressure 1000 kPa, and the exit pressure is 150 kPa. The turbine produces 100,000 kW. Determine (a) the exit temperature; (b) the mass flow rate kg/sec.RHe= 2.077 kJ/kg.K; k=1.666. And draw the P-V and T-S diagram.
HANDWRITTEN AND THE FINAL ANSWER SHOULD BE IN ENGLISH SYSTEM A process innovated by Engr. Santioque is considered to be in a constant pressure. If there is ten kilograms of air has a decrease of internal energy of 55 BTU while its Fahrenheit temperature is reduced to one fifth of the initial temperature during a reversible non flow process. Determine (a) the initial and final temperatures, (b) heat, (c) work, and (d) the change in entropy.
a) A nozzle is a device that is used to increase the velocity of a fluid by varying the cross-sectional area. At the last section of a jet engine (Fig Q1.a, section 5), air with a mass flow rate of 50 kg/s at a pressure of 500 kPa and a temperature of 600 K enters a nozzle with an inlet cross-sectional area of 5 m2. The exit area of the nozzle is 20% of its inlet area. The air leaves the nozzle at a velocity of 300 m/s. The nozzle is not well-insulated and during this process, 5 kJ/kg heat is lost.Figure Q1.a: Schematic of a Jet engine.(i) In analysing this nozzle using the 1st law of thermodynamics, the change in which type of energy is negligible? (ii) Determine the density and velocity of the air entering thenozzle.(iii) Calculate the density of the air as it leaves the nozzle.l(iv) Determine the temperature of the air as it leaves the nozzle. ((v) Calculate the pressure of the air as it leaves the nozzle Only solve V please
K 1.calculate virtual temp of air with an actual temperature of 25C and pressure of 950hpa, and the following characteristics. i) no water vapor and with no condensed water; ii) at 50% relative humditiy, and iii) saturated with water vapor and with no condensed water.
Gaseous carbon dioxide (CO2) enters a tube at 3 MPa and 227ºC, with a flow of2kg/sec. That CO2 cools isobarically while passing through the tube, and at the exit, thethe temperature drops to 177°C. Determine the specific volume of corrected CO2through the compressibility factor at the outlet. pressure is: