Which of the following is correct? The job of splitter in GC is taking part of the sample.Column in GC should be placed in a temperature-programmable oven.Pressure drop drrection factor, j, is used because of gas compressibility inside the column.The microflash vaporizer "instantly" volatilize the solvent and analytes and sweep them into the column.all of the above is correct

Introduction Splitter as the name suggests splits the sample. It controls the amount of sample that…

O The job of splitter in GC is taking part of the sample. O Column in GC should be placed in a temperature-programmable oven. Pressure drop correction factor, j, is used because of gas compressibility inside the column. The microflash vaporizer "instantly" volatilize the solvent and analytes and sweep them into the column. O all of the above is correct

O The job of splitter in GC is taking part of the sample. O Column in GC should be placed in a temperature-programmable oven. Pressure drop correction factor, j, is used because of gas compressibility inside the column. The microflash vaporizer "instantly" volatilize the solvent and analytes and sweep them into the column. O all of the above is correct

Biomedical Instrumentation Systems

1st Edition

ISBN:9781133478294

Author:Chatterjee

Publisher:Chatterjee

Chapter19: Biomedical Laboratory Instrumentation

Section: Chapter Questions

Problem 7P

See similar textbooks

Similar questions

In sterilization, which among the supplies, instruments, glassware, etc. under the list of materials can be sterilized using either or both equipment below? List them down under the category: a) For “autoclaving” only, B) For Dry heat oven sterilization ,And C) Can be sterilized with either. Materials: 200-ml Erlenmeyer flask Stove 500-ml Erlenmeyer flask Autoclave 10-mL graduated cylinder Analytical balance 100-ml graduated cylinder pH meter Spatula Stirring rod 100-mL beaker Test tubes Distilled water Petri dish Stirring rod Alcohol lamp Glass dropper
You want to dilute a sample by 1/3. For a final volume of 27 ml, how much sample would you add to how much liquid media?
Which of the following statements about AAS and AES is FALSE a)Sample used in AAS are usually in the form of aqueous solution b)In flame AAS, the flame is used for atomization as well as excitation purpose c)The graphite furnace is an example of non-flame atomizer d)In flame AES, no light source is required. What is the advantages of Axial torch configuration over Radial configuration in Inductive Couple Plasma-Optical Emission Spectrometer (ICP-OES) a)Increased radiation intensity – a longer path length b)Excellent tolerance to dissolve solids c)Can analyze S, P, and Halogens d)Excellent torch lifetimes
The labware we used in Quant Lab is divided into “qualitative” or “quantitative” analytical purpose. One of the important laboratory skills we learned is to know what specific apparatus is appropriate for the task at hand. For the following procedures, which SPECIFIC glassware, or balance ( CORRECT NAMES, be specific ) should be used? Mix K2Cr2O7 and KI solutions to be ready for titration. The mixture container is _______________ Measure the mV values of fluoride standard and sample solutions. Theoretically, the solution containers should be _______________________ Weigh 1 g solid KSCN that is poured into the thiosulfate – iodine titration. __________________
What precautions should we follow when conducting experiment in Environmental lab? How can you determine chloride content in a waste water sample?
A 46.60-gram pycnometer was filled with 100.50 grams of liquid. When filled with insoluble powder, the pycnometer weighs 84.60 grams. When the insoluble powder and liquid were combined, the pycnometer weighed 172.8 grams. What is the relative density of the insoluble powder? 2.1 2.6 3.1 None of the Above
Which of the following is/are source/s of error in performing a spectrophotometric method? Answer all that apply. Sample is turbid when the absorbance is read. The absorbances were read at maximum absorption. Standard solutions are prepared accurately. The cuvettes have fingerprints.
Design a serial dilution of a sample to achieve a A) Final dilution of 10-4 using 9.0 mL blanks B) Final dilution of 10-6 using 99 mL blanks C) Final dilution of 10-6 using 9.0 mL blanks
Which of the following specimens cannot be tested on the Velocity Macroscopic Chemistry Module? a. Gross Hematuria b. Specimens <2 mL c. Pyridium d. Diluted Specimens e. All of the above
If you were to break a laboratory mercury thermometer, flushing the liquid mercury down a sink would be an inappropriate method of disposal because: mercury toxicity increases when mixed with water mercury is subject to biological magnification dilution of the mercury waste would be insufficient all of the above
A sample was placed on a chromatography column. Dichloromethane was used as the eluting solvent. All the components were eluted off the column, but no separation was observed. What must have been happening during this experiment? How would you change the experiment to overcome this problem?
A pesticide with high vapor pressure has more ability to penetrate through a fine textured , true or false.