Optimum cell concertation is very important for successful bone marrow culture. A technologist received 2.7 ml bone marrow specimen with concentration 20 x 10^6 cell/ml, she add 1ml this bone marrow to 9 ml Marrow-Max culture medium to set up a bone marrow culture. What is final cell concentration in this bone marrow culture?

Optimum cell concertation is very important for successful bone marrow culture. A technologist received 2.7 ml bone marrow specimen with concentration 20 x 10^6 cell/ml, she add 1ml this bone marrow to 9 ml Marrow-Max culture medium to set up a bone marrow culture. What is final cell concentration in this bone marrow culture?

Principles of Instrumental Analysis

7th Edition

ISBN:9781305577213

Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Publisher:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Chapter21: Surface Characterization By Spectroscopy And Microscopy

Section: Chapter Questions

Problem 21.12QAP

See similar textbooks

Similar questions

In a filtration of suspended cells under full vacuum using a 20 cm Büchner funnel, you collect data for the volume of filtrate as a function of time. What changes you can make to decrease the time required to filter a given volume?
0.5M HA sample with 0.2 dissociation; It is placed in a conductivity cell with a length of 0.9 cm and an area of 2 cm2 and its conductivity is read as 300 mS. For this purpose;a) Equivalent conductivity of the electrolyte ?b) Boundary equivalent conductivity ?c) Decomposition constant ?
The concentration of a culture decreases as it is serially-diluted. If you started with a culture which initially has a cell concentration of 6.0 x 108 cells/mL and you serially dilute it 1/200, 1/50, and then 2 x 10-3, what would be the concentration after each dilution?
The data below was obtained with a Cl- ISE to prepare a plot of mV vs. log[Cl-]. Assume the unknown saltwater solution was diluted as in the procedure before being measured. What is the ppm Cl- of the undiluted unknown solution? Cl- Concentration (ppm) Potential (mV) 10 160 100 94 1000 40 Diluted Unknown Saltwater 132
A 10 ml of ascorbic acid (MW=176.1) injection was transferred to a 100 ml volumetric flask and made up to volume with deionized water. A 20 ml of the diluted injection was transferred to a conical flask and titrated with Iodine VS using starch mucilage as the indicator. The iodine solution was standardized against a solution of sodium thiosulfate primary standard (MW=248.2). Results: Weight of sodium thiosulfate used to prepare 100 mL primary standard solution = 2.501 g Volume of thiosulfate solution required to titrate 25 mL of Iodine solution = 24.83 mL Volume of iodine solution required to titrate 20 mL of the diluted ascorbic acid injection = 21.55 mL Stated content of the injection = 10% w/v Calculate the % of the stated content in the injection. (Round-off your answer to 2-decimal places) Answer = ____%
A 10 ml of ascorbic acid (MW=176.1) injection was transferred to a 100 ml volumetric flask and made up to volume with deionized water. A 20 ml of the diluted injection was transferred to a conical flask and titrated with Iodine VS using starch mucilage as the indicator. The iodine solution was standardized against a solution of sodium thiosulfate primary standard (MW=248.2). Results: Weight of sodium thiosulfate used to prepare 100 mL primary standard solution = 2.501 g Volume of thiosulfate solution required to titrate 25 mL of Iodine solution = 24.83 mL Volume of iodine solution required to titrate 20 mL of the diluted ascorbic acid injection = 21.55 mL Stated content of the injection = 10% w/v Calculate the % of the stated content in the injection.
4. determine the amount in mg of the amount of Ag present from ICP mass digested: 1.0821g/L dilution of 10ml stock solution to 100ml volumetric flask X=0.98 (intensity)
Describe an electrochemical sensor assay method for rapid bacterial detection and identification.What are the principles and mechanisms involved?
Which statement is correct? A) An internal standard is a different substance from the analyte. B) An internal standard is the same substance as the analyte. C) An internal standard is a same substance as the analyte matrix.
An analyst wants to find out the active surface of his electrode before conducting his analyzes. To do this, he carried out a series of measurements by cyclic voltammetry (CV) using a 1 mM solution of K4Fe(CN)6 dissolved in 0.1M NaCl. He recorded the anodic peak intensity (ip) corresponding to the oxidation of Fe(II) to Fe(III) as a function of the scanning speed (v) of the CV (see table). What is the active surface of the electrode? Data: Fe diffusion coefficient (CN)64-, D = 6.67x10-6 cm2/s Randles-Sevcik equation ip = (2,69x105)n3/2ACD1/2v1/2 rate (v/s) ip (A) 5,00E-02 5,75E-05 1,00E-01 7,68E-05 2,00E-01 9,94E-05 5,00E-01 1,42E-04 1,00E+00 2,07E-04
A 0.2653 g of pure potassium dichromate was dissolved in 15 mL of 1.5 M sulfuric acid and transferred to a 250.0 mL volumetric flask and diluted to the mark with distilled water. A 25.0 mL aliquot of this solution was transferred to another 250.0 mL volumetric flask and diluted to the mark with distilled water and this solution has an absorbance 0f 0.387 in a 2.00 cm cell. Calculate the molar absorptivity of potassium dichromate.
You are given a container with Na3PO3 that is reportedly contaminated. You are asked by your supervisor to determine the percent purity of that sample in order to know the next measures to be taken by the plant. The following are the procedures that you need to do: a. Dissolve sample weighing 1 g in 35 mL water. b. Prepare solution with 45 mL 3% w/v HgCl2, 30 mL 10% w/v C2H3NaO2 and 10 mL CH3COOH. c. Digest sample then filter then rinse the precipitate that weighs 0.2857 g. d. Compute for the % purity.