are given a container with Na3PO3 that is reportedly contaminated. You are asked by your supervisor to determine the percent purity of that sample in order to know the next measures to be taken by the plant. The following are the procedures that you need to do: a. Dissolve sample weighing 1 g in 35 mL water. b. Prepare solution with 45 mL 3% w/v HgCl2, 30 mL 10% w/v C2H3NaO2 and 10 mL CH3COOH. c. Digest sample then filter then rinse the precipitate that weighs 0.2857 g. d. Compute for the % purity

are given a container with Na3PO3 that is reportedly contaminated. You are asked by your supervisor to determine the percent purity of that sample in order to know the next measures to be taken by the plant. The following are the procedures that you need to do: a. Dissolve sample weighing 1 g in 35 mL water. b. Prepare solution with 45 mL 3% w/v HgCl2, 30 mL 10% w/v C2H3NaO2 and 10 mL CH3COOH. c. Digest sample then filter then rinse the precipitate that weighs 0.2857 g. d. Compute for the % purity

Principles of Instrumental Analysis

7th Edition

ISBN:9781305577213

Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Publisher:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Chapter33: Automated Methods Of Analysis

Section: Chapter Questions

Problem 33.5QAP: Give the advantages and disadvantages of sequential injection analyzers compared to traditional flow...

See similar textbooks

Similar questions

Method used was Volhard Method Sample preparation: 5ml sample diluted in 100 ml. 20ml aliquot was used for analysis. Concentration of AgNO3: 0.0609M Calculate mass of NaCl and % NaCl (w/v)
4 litres of water obtained from a borewell in Vellore contains FeSO4 = 30.4 mg; CaSO4 = 13.6 mg; MgCl2 = 38 mg; Ca(HCO3)2 = 32.4 mg; Mg(HCO3)2 = 14.6 mg and NaCl = 11.7 mg. Calculate temporary, permanent and total hardness of the water sample in ppm. (Atomic masses of Fe = 56; Ca = 40; Mg = 24 and Na = 23)
The standard addition method is used to analyze a sample of a river water for mercury. Solution A is made by pipetting 5.00 mL of undiluted sample in to a 10 mL volumetric flask and filling to the mark with DI water. Solution B is made by pipetting 5.00 mL of undiluted sample and 3.00 mL of 15.0 ppb of Hg standard into same 10.0 mL volumetric flask and filling to the mark with DI. Solution A and B are analyzed using atomic absorption spectroscopy and give a percent transmittance values of 56 % and 33 % respectively (not blank corrected). A blank has a transmittance of 96%. What is the corrected absorbance of both solution A and B? A. Solution A: 0.123 Solution B: 0.463 B. Solution A: 0.463 Solution B: 0.234 C. Solution A: 0.123 Solution B: 0.234 D. Solution A: 0.234 Solution B: 0.463
Make a schematic diagram for the procedure below: B. % SO3 determination Dry the soluble sulfate sample at 100° C for 1-2 hours, and cool in desiccator. Weigh out 0.5 – 0.7 g (± 0.3 mg) duplicates sample. Transfer to 400-mL beakers. Dissolve each in 200 mL of dist. H2O + 4 mL of 6 m HCl. Precipitant is prepared by dissolving 1.3 g BaCl2 ∙ H2O in 100 mL water. Filter if solution is not perfectly clear. Heat the BaCl2 solution and sulfate sample solution nearly to boiling, and then add the entire amount to the HOT sulfate sample solution while stirring vigorously. Wash stirring rod with distilled water and include washings in your final mixture. Digest by letting stand 1-2 hours. Overnight standing is acceptable. Filter through an ash less filter paper of fine porosity (Whatman no. 42). Slowly pour the supernatant liquid through the filter paper.
Rinse and fill the buret with 0.100 M HCl solution. Transfer accurately 25.0 mL of saturated calcium hydroxide solution (2g of calcium hydroxide per 100 ml of water) into two separate E-flasks. Add 2 drops of phenolphthalein to each flask and titrate each solution until the pink color disappears. Voume of HCl used: Trial 1= 6.80ml; Trial 2 = 6.30mL Determination of solubility and Ksp of calcium hydroxide 2. Compute for the moles of H+ used and the moles of OH- present. moles of H+ used = (concentration of HCl) × (volume of HCl used)moles of OH- = moles of H+ used 3. Construct an ICE table for the reaction.4. Calculate the molar solubility (in mol/L) of OH- and Ca2+.5. Determine the solubility of Ca(OH)2 in g/L. (MM of Ca(OH)2 = 74.096 g/mol)6. Calculate the Ksp of Ca(OH)2.7. Compute for the percent error of the experimental value for Ksp of Ca(OH)2 with the literature value.(Ksp of Ca(OH)2 = 8.0 × 10-6 at 25°C)
Accurately weigh out about 6g copper(ii) sulfate crystals into a weighing boat. Use the copper(ii) sulfate crystals to make up 250cm3 of standardized copper (ii) sulfate solution Pipette 25cm3 of this solution into a conical flask Add 1.5g potassium iodide and swirl thoroughly Titrate this solution with standard 0.1 moldm-3 Na2S2O3 in a burette. When the iodine color fades, add 1 cm3 starch indicator. Use your titration data below to calculate the percentage by mass of copper in the copper(ii) sulfate crystals.
25 ml of pickled brine was taken from an apple pickled with vinegar and diluted to 500 ml, 25 ml of this was taken and acidity was determined with 0.2 N (Factor: 1.05) NaOH. In the main trials, 6.3 ml - 6.5 ml - 6.9 ml, respectively, 0.1 ml base was used in the analysis without using the sample.For example, how many ppm is its acidity?
You obtain an Unknown Sample from the Stockroom. You begin testing the solution through the steps outlined in the flowchart of the experiment’s PDF file. You first add HCl and centrifuge your mixture. You observe the formation of a white precipitate in the bottom of the test tube. After pouring off the supernatant liquid, you add hot water to the white precipitate. Upon addition of the hot water, you have some white precipitate still at the bottom of the test tube, and the supernatant liquid is poured off. To this liquid, potassium chromate (K2CrO4) is added. Upon this addition of potassium chromate, you observe no formation of precipitate. Which of the following is a valid conclusion to draw at this point? (Choose one.) Select one: 1. Hg22+ is definitely present. 2. Pb2+ is NOT present. 3. Ag+ is definitely present. 4. Pb2+ is definitely present.
5.00 mL of stock solution is diluted to 25.00 mL, producing solution ALPHA. 10.00 mL of solution ALPHA is diluted to 25.00 mL, resulting in solution BETA. 10.00 mL of solution BETA is then diluted to 25.00 mL, producing solution GAMMA. dilution factor for ALPHA from stock solution = 0.167 dilution factor for BETA from ALPHA solution = 0.0476 part c and d?
60 ml of standard hardness containing 1 mg of pure CaCO3 per ml consumed 22 ml of EDTA. 40 ml of water sample consumed 20 ml of EDTA solution using EBT indicator. 40 ml of water sample after boiling, filtering consumed 15 ml of EDTA. Calculate the temporary and permanent hardness of water sample.
Based on the data, calculate the concentration of analyte in the ORIGINAL sample in ppm. Report to 1 decimal place Sample: A 10.00 mL aliquot of the unknown was placed in a 100.0 mL volumetric flask and made up to the mark will distilled water. The absorbance of this solution is 0.185. Sample + Spike: A 10.00 mL aliquot of the unknown and a 13.00 mL aliquot of the 46.00 ppm stock were both placed in the same 100.0 mL volumetric flask and diluted to the mark with water. The absorbance of this solution is 0.326. ( Please type answer note write by hend)
Rinse and fill the buret with 0.100 M HCl solution. Transfer accurately 25.0 mL of saturated calcium hydroxide solution (2g of calcium hydroxide per 100 ml of water) into two separate E-flasks. Add 2 drops of phenolphthalein to each flask and titrate each solution until the pink color disappears. Using the titration data for the determination of solubility and Ksp of calcium hydroxide: Parameter Trial 1 Trial 2 Final Buret Reading (mL) 5.80 12.20 Initial Buret Reading (mL) 0.00 5.80 Temperature (in celcius) 25 25 Construct an ICE table for the reaction