Pum2 cm I.D.Ball ValvePatmProblem 2: The drain on a large tank of liquid consists of a ball valve with a 2 cm inside diameter that connectsto the tank with a well-rounded flow entrance. The height of the fluid surface above the valve entrance isdenoted h. The pressure in the air space above the surface of the fluid is the same as that outside of the tank,Patm. Taking the losses to come solely from the ball valve and its entrance region, perform the following analysis:a. Find the velocity of the flow through the valve and the flow rate (in liters/sec) when h = 6 meters andthe valve is fully open.b. Find the increase in fluid height h required to maintain the same flow rate as that found in Part a. withthe ball valve 1/3 closed.c. How does the change in fluid height in Part b. compare with the increase in head loss caused by thepartial closing of the valve?

(a) Consider the losses due to friction is negligible. Apply the Bernoulli equation between the…

Answered: Pum 2 cm I.D. Ball Valve Patm Problem…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At the gasoline transfer facility (ρᵣₑₗ=0,75) from the pond of storage to consumption, you want to install a pump to circulate a flow of 40(lt/s). The 400m long pipe is cast iron 150mm in diameter and consists of a check valve, a gate valve and 2 commercial medium radius elbows. The consumption tank is pressurized to 2,9 (kgf/cm²) gauge pressure. Decide the drive power of the pump in KW if its performance is 70%. •Additional data, pressure drop factors: •Retention valve Kᵣ = 1,5 •Gate valve open Kᵥ = 0,21 •Medium Radius Commercial Elbow Kc = 0,75 for each cubit •Storage pond outlet sharp angles Kₛ = 0,5 •Entrance to consumption pond Kₑ = 1 •Friction factor in pipes f = 0.026
A pump is being used to transport a liquid food product (density p=1000kg/m^3, viscosity 0.001 Pa s) from holding tank to filling a machine at a mass flow rate of 2 kg/s. The liquid level in the holding tank is 10 m above the pump, and the filling machine is 5 m above the pump. There is 100 m of 2-in nominal diamter sanitary pipe between the holding tank and the filling machine, wiht one open globe valve and four regular 90° flanged elbows in the system. Within the system, there is a heat exchange which causes 100 kPa of pressure drop due to friction. The holding tank is open to atmosphere, and filling machine is running at a pressure of 1.5 atm. The diamter of the filling machine pipe is 3cm. A: What is the volume flow rate of the system? B: What is the diamete of the pipe? C: What is the average velocity inside the pipe? D: What is the reynolds number of the flow in the pipe? E: What is the flowing type?
When a pump with a suction and discharge pressure of 125 kPa and 409 kPa are used, the flow rate is 30L/s into a pipe with a diameter of 4 cm. Approximately 10cm in diameter, the suction diameter. What is the energy added to the water by the pump in meters
A fully-filled open storage tower of height 32 m and diameter 3.0m supplies water to a house. A horizontal pipe at the base of the tower has a diameter of 2.54cm. To satisfy the needs of the home, the supply pipe must be able to deliver water at a rate of 0.67 gal/s. a. If water were flowing at the maximum rate, what would be the pressure in the horizontal pipe?b. A smaller pipe, of diameter 1.27 cm supplies the second floor of the house, a distance of 7.2 m above the ground level. What are the flow speed and water pressure in this pipe?
At the bottom of a pressurized water tank is a mouth with a diameter of 5 cm, where water is discharged into the atmosphere. The water level is 2 m above the outlet. The tank air pressure above the water level is 300 kPa (absolute) and the atmospheric pressure is 100 KPA. Determine the initial rate of water discharge (volumetric flow rate) from the tank, neglecting the effects of friction.
In a liquor-bottling plant erected at a site 1 km above sea level (Patm=0.898 bar and temperature 8.7°C) where a centrifugal pump discharges 20 l/s of water against a head of 28 m while the cavita on parameter of the pump a=0.5. Where should the pump inlet location be in m with respect to the water surface.
Pump Horsepower in Brine System. A pump pumps 0.200 ft3/s of brine solution having a density of 1.15 g/cm3 from an open feed tank having a large cross-sectional area. The suction line has an inside diameter of 3.548 in. and the discharge line from the pump a diameter of 2.067 in. The discharge flow goes to an open overhead tank, and the open end of this line is 75 ft above the liquid level in the feed tank. If the friction losses in the piping system are 18.0 ft lbf/lb m, what pressure must the pump develop and what is the horsepower of the pump if the efficiency is 70%? The flow is turbulent.
Water from a reservoir is pumped over a hill through a pipe 450 mm in diameter and a pressure of 1 kg/cm2 is maintained at the summit. Water discharge is 30 m above the reservoir. The quantity pumped is 0.5 m3/sec. Frictional losses in the discharge and suction pipe and pump is equivalent to 1.5 m head loss. The speed of the pump is 800 rpm what amount of energy must be furnished by the pump, kW?
When a pump with a suction and discharge pressure of 125 kPa and 409 kPa are used, the flow rate is 30L/s into a pipe with a diameter of 4 cm. Approximately 10cm in diameter, the suction diameter. What is the power delivered to the water by the pump in hp
Water is pumped to a storage tank from a pool by a centrifugal pump. The elevation difference between the pool and the storage tank is 60 m. The stórage tank and the pool are open to atmosphere. 50 meters of 6 in Sc 40 steel pipe is used between pool andpump. After the pump 6 in Sc 40 pipe with a length of 22 m is suddenly contracted to 4 in Sc 40 pipe, that is 70 m. The flow rate of water is 2.5 m/min and the temperature is 20°C. If the pump efficiency is 0.6 and the cost of electrical energy is 0.40 TL/kWh,calculate daily cost of electricity used for this system
The diameter of an open topped tank 1.5 m high increases uniformly from 4.2 m at the base to 6 m at the top. Discharge from the base of the tank takes place through a 75 mm diameter pipe which is 3 m in length. The pipe discharges the water to the atmosphere 1.5 m below the base of the tank. Initially, the tank is fully filled with water. Take f =0.01. Find the time to empty the tank.
As can be seen in the figure, the level difference between the two tanks open to the atmosphere is H = 25 m. The fluid in the lower tank is pumped into the upper tank with the help of a centrifugal pump. The continuous loss coefficient of the pipe made of forged steel, f = 0.025, the elbow loss coefficient K = 1. Other losses in the system are neglected. The pipe diameter is D = 16 cm and the flow through the pipe is V = 0.15 m3 / s. According to this;a) Find the pump power.b) Find the pressure at the pump suction pipe inlet.c) Find the pressure at the pump discharge pipe outlet.d) Draw the Energy Slope line and Hydraulic slope lines .

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS