Q) A single plate clutch has to transmit 75 kWat 3000 r.p.m. The spring exerts an axialpressure of 7.35 N/cm3. Determine the innerand outer diameters of the friction surfaces ifthe ratio of the two diameters is 1.5.

Q) A single plate clutch has to transmit 75 kW at 3000 r.p.m. The spring exerts an axial pressure of 7.35 N/cm³. Determine the inner and outer diameters of the friction surfaces if the ratio of the two diameters is 1.5.

Q) A single plate clutch has to transmit 75 kW at 3000 r.p.m. The spring exerts an axial pressure of 7.35 N/cm³. Determine the inner and outer diameters of the friction surfaces if the ratio of the two diameters is 1.5.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A cone clutch for industrial use is to transmit 15 hp at 400 rpm. The mean diameter of the clutch is…

Q: Question 3 An engine of a 2 ton truck develop 30 kW at 600 rpm. The truck is fitted with a cone…

A: For answer refer the next page.

Q: The pitch of 48 mm mean diameter threaded screw of a screw jack is 12.0 mm. The coefficient of…

A: Given Data The diameter of the screw is: d=48 mm The pitch of the threaded screw of a screw jack…

Q: Find the force required to move a load of 300 N up a rough plane, the force being applied parallel…

Q: Two machines are coupled by means of a clutch plate with 2 contact surfaces. The plate has an inner…

A: GIVEN WE have,contact surface clutch plate inner diameter (d1 )=130mm=0.13mtrouter diameter (d2…

Q: In an experiment to find the coefficient of static friction, two plates (e) made of the sam…

A: cosθ N for m1=0.2kg N for m2=0.4kg cos20 1.87 3.75 cos30 1.73 3.46 cos40 1.53 3.06

Q: Q2) A single block brake is shown in Fig.The diameter of the drum is 250 mm and the angle of contact…

Q: An automobile single plate ciutch consists of a pair of contacting surtaces. The inneOr and outer…

Q: Q2 ) A cone clutch is to transmit 10 KW at 600 r.p.m. the cone has a face angle of 10° The width of…

A: Given, Power transmitted , P =10 Kw Speed, N =600 rpm Cone angle = 10 degree maximum pressure , Pr…

Q: Find the friction force if coefficient of friction 0.3 and normal force is 120 N

A: Given data : Coefficient of friction=μ Normal force=N To find : Friction force

Q: A centrifugal clutch is to transmit 15 kW at 900 r.p.m. The shoes are four in number. The speed at…

A: Centrifugal clutches generally consists of motor pulleys. Inside the rim of these pulleys, various…

Q: An automobile engine develops 25 kW at 1,000 rpm. The clutch used to transmit this power in a…

Q: II pelt tensions at the limiting value of friction is dependant on the coefficient of dry angle of…

Q: Q2/ As shown in fig.(2). Prove the main equation for the coefficient of frictional force between the…

Q: Determine the axial spring force necessary to engage the clutch, when an engine developing 30kW at…

A: Given Data: p = 30kW = 30 * 103 W N = 500rpm α = 13.4o D = 300mm => R =…

Q: shown below. The coefficient of friction for the screw is f = 0.06 and friction du negligible f≈ 0.…

Q: Q2: Complete the sentences? 1- If the maximum friction force is 100 KN and normal force is 10 KN,…

A: (1) The maximum friction force f=100 KN, and the normal force N=10 kN then the value of friction…

Q: Find the coefficient of friction if friction force is 723N Normal force is 823 N

A: Given data : Normal force=N Friction force=F Required : Coefficient of friction

Q: Question :- A conical pivot bearing supports a vertical shaft of 200 mm diameter. It is subjected to…

A: The solution is given below

Q: Q1) The mean diameter of the driving pulley for a vee-belt drive with two belts is 110 mm. The…

A: dmean=110 mmP=4.4 KWN=1500 rpmμ=.32Angle of lap θ=160°A=120 mm2

Q: A rope making 1 ¼ turns around a stationary horizontal drum is used to support a heavy weight. If…

Q: 6.10. A car with its brakes locked will remain stationary on an inclined plane of dry concrete when…

A: Given Angle = 45o

Q: A cone clutch is to transmit 30 kW at 1250 rpm. The face angle of the cone clutch is 12.5o and the…

Q: A car engine has its rated output of 16 kW. The 2 maximum torque developed is 120 N-m. The clutch…

A: Given data as per the question power of car engine =16 kwMaximum torque developed =120 N.maxial…

Q: QIA double shoe brake, as shown in Fig. The diameter of the brake drum is 250 mm and the contact…

A: According to the information we have the double shoe brake. The brake drum diameter is 250 mm and…

Q: AN ENGINE DEVELOPING 45 KW AT 1000 R.P.M IS FITTED WITH A CONE CLUTCH BUILT INSIDE THE FLYWHEEL. THE…

A: The answer is in next step

Q: Q2 ) A cone clutch is to transmit 10 KW at 600 r.p.m. the cone has a face angle of 10 The width of…

Q: 2 A ladder 5 m long and weighing 260 N is placed against a vertical wall at an inclination of 30 ^ 0…

Q: A multi disc clutch has five plates having four pairs of active friction surfaces. If the intensity…

Q: n a belt arrangement two pulleys are connected by flat belts having same diameters. The maximum…

A: Since the two pulleys are connected by flat belts, therefore, the lap angle is 180 degrees.

Q: Find the value of coefficient of friction if friction force is 200 N and Normal force is 780 N

Q: The band brake of Fig. is used to control the rotation of a drum. The coefficient of friction…

A: First, draw the free-body diagram of the handle: Now write the momentum equation about the point O.…

Q: The frictional coefficient has a value of 0.26795, and the normal force is 20kN. Determine the angle…

Q: An overhung cast iron pulley transmits 7.5 kW at 400 r.p.m. The belt drive is vertical and the angle…

Q: Find the value of coefficient of friction if friction force 34 N and normal force is 120 N

A: Given data : Friction force=f Normal force=N' Required : Coefficient of friction

Q: A)It is required to use a multiplate clutch to transmit power of 24 kW at 1200 r.p.m If the clutch…

Q: 2. A pulley is driven by a flat belt running at a speed of 600 m/min. The coefficient of friction…

Q: Exomple: An automotive single-plate clutch with o pairs of frichon Surfaces, tvansmits a 300. N-m…

A: For single plate clutch : Torque (T)=300 N-m speed (N)= 1500 rpm inner dia.(d) = 170 mm outer…

Q: The pressure distribution at the pivot bearing's surface of contact changes, as indicated. Determine…

A: Given data Friction as considered for calculating the Torque. Where Pressure are distributed as on…

Q: A uniform ladder of length 3.25 m and weighing 250 N is placed Against a smooth vertical wall with…

Q: A multi disc clutch has five plates having four pairs of active friction surfaces. If the intensity…

A: Given:Total number of plates=5n1+n2=5number of active plates=4Pressure, P=0.127 N/mm2speed, N=500…

Q: the radius of each pulley is 5 inches and the coeffiecent of friction is 0.3 a) determine the…

Q: A single plate clutch is required to transmit 150 kW at 6000 r.p.m. The clutch facings available…

A: The answer is given below

Q: Steel pulleys, 120 mm and 530 mm in diameter are to transmit 2.50 kW at 1100 rpm of the smaller…

A: The ratio of net tension: T1 / T2 = 2.85

Q: Q5. What should be the value of the angle 0 in fig. so that the motion of the 90N block impends down…

A: Draw the free body diagram of the smaller block (consider block 1) having weight of 30 N.

Q: An automobile engine develops 33.5 hp at 1,000 rpm. The clutch used to transmit this power in a…

Q: The lead screw of a lathe has a 2.0-in single Acme thread, 2½TPI. To drive the tool carriage, this…

A: Answer: (a) The power required to drive the screw is 0.111248 hp. (b) The efficiency of the screw…

Q: Determine the axial force required to engage a cone clutch transmitting 25 kW power at 750 rpm.…

Q: 2. The power transmitted by a belt drive is 2.5 kW. The line ar velocity of the belt is 2.5 m/s. The…

Q: In the given figure, W= 200kg. Assume that the coefficient of friction between surfaces is 0.40.…

Question

Q) A single plate clutch has to transmit 75 kW
at 3000 r.p.m. The spring exerts an axial
pressure of 7.35 N/cm3. Determine the inner
and outer diameters of the friction surfaces if
the ratio of the two diameters is 1.5.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 250N crate is pulled up a ramp that is angled at 20 degrees above the horizontal. If the coefficient of friction is 0.25, find the y-component of the weight.
Having the coefficient of frictions (μs = 0.40 and μk = 0.30), Determine whether the block is in equilibrium(explain) and find the value of the magnitude and the direction of the actual force if:a) P = 230lbb) P = 350 lb
Determine the coefficient of static -friction force (µs) if ᴓs= 45?
An object weighing 400 N is held by a rope that passes over a horizontal drum. The coefficient of friction between the rope and the drum is 0.25. If the angle of contact is 150 degrees, determine the force that will raise the object.
2 A ladder 5 m long and weighing 260 N is placed against a vertical wall at an inclination of 30 ^ 0 with wall. A wan weighing 780 N climbs the ladder. When he is at a distance of 1.64 m along the ladder from lower all contact surfaces? end, the ladder slips. What is the coefficient of friction assuming it to be same for
In the given figure, W= 200kg. Assume that the coefficient of friction between surfaces is 0.40. Which of the following most nearly gives the required force P to raise the block?
A 30 KN of force at one end just supports a weight of 30,000 KN load at the other end. If the rope is run three times around a circular post, what is the coefficient of friction between the rope and the post? How to get the final answer 0.366?
17. A 430-kg block is resting on a 27 deg inclined plane with a coefficient of friction = 0.64. Find the required horizontal force P (in kN) that is necessary to start the block UP the incline. Round off to two decimal places.
The pitch of 48 mm mean diameter threaded screw of a screw jack is 12.0 mm. The coefficient of friction between the screw and the nut is 0.12. (a) Determine the torque required on the screw to raise a load of 27 kN, assuming the load to rotate with the screw. (b) Determine the ratio of the torque required to raise the load to the torque required to lower the load and also (c) the efficiency of the machine.
....An electric motor drives a compressor by use of V-belt. The angle of contact on the smaller pulley is 2.89 rad and the belt speed runs at 29.36 m/s. The groove angle of the pulleys is 35°. Determine the tension in the slack side of the belt in N if the belt has a cross-sectional area of 366 mm2, density 1000 kg/m3, and an allowable tensile stress of 2.3 MPa. The coefficient of friction between the belt and the pulley is 0.3
Q3/ A screw-jack is used to lft a load of 4 kN. The screw of the screw-jack is square threaded with two threads to 1 cm. If the co-efficient of friction between the nut and screw is 0,095 and outer diameter of screw s 6 cm, find the force required atthe end of the handle of length 50 cm to ift the load. (20 M)
A band brake is installed on a drum rotating at 250 rpm, and a diameter of 900 mm. The angle of contact is 1.5 pi radians and one end of the brake band is fastened to a fixed pin while the other end of the brake arm is 150 mm from the fixed pin. The coefficient of friction is 0.25 and the straight brake arm is 1000 mm long and is placed perpendicular to the diameter bisecting the angle of contact. Determine the net band pull in kN applied at the end of the brake arm if 50 kW is being absorbed.