Q.2) For the state of stress shown below, determine the orientation and values of principal stresses, the in-plane maximum shear stress, and absolute maximum shear stress using (a) Stress transformation equations (b) Mohr's Circle (c) Sketch the stress block with proper orientation for each case (Principal stress, in-plane maximum shear stress and absolute maximum shear stress).

Q.2) For the state of stress shown below, determine the orientation and values of principal stresses, the in-plane maximum shear stress, and absolute maximum shear stress using (a) Stress transformation equations (b) Mohr's Circle (c) Sketch the stress block with proper orientation for each case (Principal stress, in-plane maximum shear stress and absolute maximum shear stress).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At a point in a stressed body, the cartesian components of stress are sigma xx = 60 MPa, sigma yy= -40 MPa, sigma zz = 20 MPa, tau xy = -40 MPa, tau yz = 20 MPa, and tau zx= 30 MPa. Determine: (a) The normal and shear stresses on a plane whose outer normal has the following direction cosines: cos (n, x) = 0.429 ; cos (n, y) = 0.514; cos (n, z) = 0.743
The normal and tangential stresses on a plane inclined at 30° to the axis of the minor principal stress are 75 N/mm2 and 20 N/mm2. The resultant stress on a plane by analytical method is
The principal stresses at a point across two mutually perpendicular planes are 70 MN/m2 tension and 55 MN/m2 tension respectively. The shear stress across these planes is 25 MN/m2 (Counter clockwise). Determine the magnitude of the normal, tangential, the resultant stress, and inclination of resultant stress on a plane inclined at 25o to the plane of greater principal stress. And also verify the answer by drawing the Mohr’s circle.
At a point on the free surface of a stressed body, thenormal stresses are 20 ksi (T) on a vertical plane and 30 ksi (C) ona horizontal plane. An unknown negative shear stress exists on thevertical plane. The absolute maximum shear stress at the point hasa magnitude of 32 ksi. Determine the principal stresses and theshear stress on the vertical plane at the point.
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 12 ksi, Sy = 17 ksi, and Sxy = 18 ksi.(a) Draw Mohr’s circle for this state of stress.(b) Determine the principal stresses (σp1>σp2σp1>σp2) and the maximum in-plane shear stress τmaxτmax acting at the point.(c) Find the smallest rotation angle θpθp (counterclockwise is positive, clockwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16)
A body is subjected to a direct tensile stress of 300 MPa in one plane accompained by a simple shear stress of 200 MPa. Determine maximum normal stress on the plane.
The principal tensile stress at a point across two mutually perpendicular planes are 100 N/mm2 and 40 N/mm2. The normal, tangential and resultant stresses on a plane inclined at 20° to the axis of the minor principal stress by analytical method is
The principal stresses at a point across two mutually perpendicular planes are 70 MN/m2 tension and 50 MN/m2 tension respectively. The shear stress across these planes is 30 MN/m? (Counter clockwise). Determine the magnitude of the normal, tangential, the resultant stress, and inclination of resultant stress on a plane inclined at 30° to the plane of greater principal stress. And also verify the answer by drawing the Mohr's circle.
For the stresses of plane stress state is ?? = −8 ??? , ?? = 7 ??? and??? = −6 ???Draw a Mohr’s circle diagram.Draw stress element for the given stressesFind the principal normal and shear stresses, and determine the anglefrom the x axis to ?1Draw the stress element for the principle stress.Using stress transformation, find the principle stresses and the angle of ?1Determine the stress transformation for the angle ∅ = 25° #Answer all in detail
For the two-dimensional stress fi eld shown in Fig. it isfound thatσxx = 3000 lbf/ft2 σyy = 2000 lbf/ft2σxy = 500 lbf/ft2Find the shear and normal stresses (in lbf/ft 2 ) acting onplane AA cutting through the element at a 30° angle asshown.
A plane stress state is given by the principal stresses σx =25 MPa and σy= -11 MPa. Determine σx' in the case that the system is inclined by 30 degrees (counter-clockwise). Give your answer in MPa to the nearest whole number.
a) Prime planes,b) Prime stresses, c) Maximum shear stress and thisin the plane of the stressdetermine the normal stress