Q1/ Determine the magnitude and direction of the resultant force acting on a 45° elbow deflects water upwards and discharges it to the atmosphere at a specified rate of 30 m/sec. assume the flow is steady, frictionless, incompressible. The weight of the elbow and the water in it is considered as 50 Kg Take the density of water to be 1000 kg/m 25 cm? 45° FRY 40 cm FRS 上 150 cm? W

Q1/ Determine the magnitude and direction of the resultant force acting on a 45° elbow deflects water upwards and discharges it to the atmosphere at a specified rate of 30 m/sec. assume the flow is steady, frictionless, incompressible. The weight of the elbow and the water in it is considered as 50 Kg Take the density of water to be 1000 kg/m 25 cm? 45° FRY 40 cm FRS 上 150 cm? W

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A circular cone-shaped container is filled with water at a level h0. At time t=0 a faucet is turned on and starts filling the cone with water at a constant flow rate Q. (a) Determine the expression for the variation of the level of water with time in terms of the initial level and volume (h0, V0) and the feed flow rate Q. (b) At what time will the water start to spill over if the cone was initially filled to 1/3 of the cone's total height? Determine a numerical value for the time in the case where the cone angle is 45o, h0=20cm and Q=2l/s.
A sharp-edged orifice in the vertical wall of a large tank has a diameter of 25 mm. The coefficient of contraction is 0.620 and the coefficient of velocity is 0.98. If the jet drops 936 mm in a horizontal distance of 2.490 meter from the vena contract, Determine the power loss in watts. a. 5.26 Watts b. 3.78 Watts c. 2.5 Watts d. 1.16 Watts
Water of density ? =998.2kg/m3 flows through a fireman’s nozzle—a converging section of pipe that accelerates the flow. The inlet diameter is d1 = 0.100 m, and the outlet diameter is d2 = 0.050 m. The average velocity, momentum flux correction factor, and gage pressure are known at the inlet (1) and outlet (2). (a) Write an expression for the horizontal force Fx of the fluid on the walls of the nozzle in terms of the given variables. (b) Verify your expression by plugging in the following values: ?1 = 1.03, ?2 = 1.02, V1 = 3 m/s, P1,gage = 137,000 Pa, and P2,gage = 0 Pa.
A 25 hp suction pump operating at 70.00% efficiency draws water from a suction line whose diameter is 184 mm and discharges into the air through a line whose diameter is 134 mm. The velocity in the 134 mm line is 1.9 m/s. If the pressure at point A in the suction pipe is -28 kPa (negative sign indicates the pressure is below the atmosphere), where A is 1.8 m below B on the 134 mm line, determine the maximum elevation above B to which water can be raised assuming a head loss of 2.4 m due to friction. Show step by step explanation.
The pipe elbow below discharges water at rate of SN/100 (m3/s) into the atmosphere at section 2 (where SN is the sum of your student number). The total volume of the passage between section 1 and 2 is equal to 0.2 m3 and the total mass of the elbow material between section 1 and 2 is equal to 10 x SN (kg). Neglect any friction losses.Calculate the horizontal and vertical forces acting on the elbow. Also calculate the resultant force and angle of force on the elbow. ****SN=21
Given the water tank A in an orifice setup that transfers water to tank B, determine the theoretical and actual velocity and flow rate if the time it takes to fill up tank B is 20 sec.
A river reach had a flood wave passing through it. At a given instant the storage of water in the reach was estimated as 15.5 ha.m. What would be the storage in the reach after an interval of 3 hours if the average inflow and outflow during the time period are 14.2 m3/sec and 10.6 m3/sec respectively.
Water at 20°C is pumped at a constant rate of 9 m3/h from a large reservoir resting on the floor to the open top of an experimental absorption tower. The point of discharge is 5 m above the floor, and friction losses in the 50-mm pipe from the reservoir to the tower amount to 2.5 J/kg. At what height in the reservoir must the water level be kept if the pump can deliver only 0.1 kW?Determine the average velocity of the water at the starting point (on the surface of the reservoir)
Water at 20°C is pumped at a constant rate of 9 m3/h from a large reservoir resting on the floor to the open top of an experimental absorption tower. The point of discharge is 5 m above the floor, and friction losses in the 50-mm pipe from the reservoir to the tower amount to 2.5 J/kg. At what height in the reservoir must the water level be kept if the pump can deliver only 0.1 kW.Determine the velocity of the water as it enters the top of the absorption tower.
A reducing elbow is used to deflect and accelerate the flow of water from a horizontal pipe to 30 ° at a rate of 14 kg / s. The elbow discharges the water into the atmosphere. The cross-sectional area at the inlet is 113 cm2 and at the outlet 7 cm2. You can neglect the weight of the elbow and of the water. It is estimated that the head loss due to the HLT elbow is equivalent to 0.3 m col of water. Determine the force (Vector) in [N] that must be applied to the flange to hold the elbow in place. Brida = flange
The head in a vessel with vertical sides and a height of 4m at the instant of opening an orifice was 3m and at closing had decreased to 1.5m. Determine the constant head under which on the same time the orifice would discharge the same volume of water. Determine the time to discharge from a head of 3m as it decreased to 1.5m if the diameter of the vessel is 2m and diameter of orifice is 50mm. Assume c = 0.60. Determine the time to empty the container.
In a rocket, the kinetic energy imparted to the consumed and ejected fuel is wasted as far as propelling the rocket is concerned. The useful power is equal to the product of the force available to propel the rocket and the speed of the rocket. If v is the speed of the rocket and u is the relative speed of the expelled fuel, show that the mechanical efficiency of the rocket is η=2uv/(u2 + v2). Explain why η = 1 when u=v.