Q1. An MRI (Magnetic Resonance Imaging) system requires precise field control It is strong magnetic. In this example, it is controlled from a single-phase bridge rectifier from a single source 60 Hz is powered by 2000 V peak, we use. Connect the magnetic model Assume the inductance series 0.5 Hand the resistance 2.5 Q. Assuming that steady state current is required Magnet A 400 A) Find the angle of fire delay. B) What is the minimum time required to reduce the magnetic current to zero?

Q1. An MRI (Magnetic Resonance Imaging) system requires precise field control It is strong magnetic. In this example, it is controlled from a single-phase bridge rectifier from a single source 60 Hz is powered by 2000 V peak, we use. Connect the magnetic model Assume the inductance series 0.5 Hand the resistance 2.5 Q. Assuming that steady state current is required Magnet A 400 A) Find the angle of fire delay. B) What is the minimum time required to reduce the magnetic current to zero?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Determine the transfer function for a tubular heat exchanger similar to the one shown in Figure 2.3 and described by the following differential equation: ** Please see attachment
A dc power supply is to be developed by employing an ac to dc converter as a power processing converter for 180 watts highly inductive load. The rms value of the input ac phase voltage is 230 V at 50 Hz frequency. Select a suitable rectifier circuit having improved ripple factor and power factor for this application. The output dc voltage is assumed (245). The output dc voltage should be multiplied with ‘0.5’ if it exceeds the 200 V.A dc power supply is to be developed by employing an ac to dc converter as a power processing converter for 180 watts highly inductive load. The rms value of the input ac phase voltage is 230 V at 50 Hz frequency. Select a suitable rectifier circuit having improved ripple factor and power factor for this application. The output dc voltage is assumed to be (245). The output dc voltage should be multiplied with ‘0.5’ if it exceeds the 200 V.
a) If Vac= 20V, Vab=? b) If Vac= 20V , Vad=? C) If Vac= 20V, Vd=? d) load of third capacitor=? E) load of 2uF capacitor=? F) energy stored in the 2uFcapacitor=? G) C=?
In a Zener regulated DC power supply, the input to the regulator varies between 15 V and 19 V. The magnitude of the series resistor in the regulator circuit is 40 Ω, and the load draws a constant current of 100 mA at 9 V. Use the ideal Zener diode model. The Zener diode specifications are given as : VZ(N) = 9 V, IZ(min) = 25 mA, and IZ(max) = 200 mA. 1) What is the minimum current that will flow through the zener diode? 2) What is the maximum power that will be dissipated by the zenere diode? 3) What is the maximum power dissipated by the series resistor?
Q ) For the full- wave uncontrolled rectifier circuit supplying a series resistive Thesupply voltage is v =300 sinωt , the supply frequency is 50 Hz and the loadparameter values are: R =05 Ω,a) Sketch the diagram of electrical circuitb) Sketch the load voltage and current waveforms .c) Calculate the load currentd) Calculate the average DC load voltage Vdc .e) Calculate the supply power to the loa
2. An AC voltmeter uses a bridge rectifier with silicon diodes and a PMMC instrument with FSD = 75 µA. If the meter coil resistance is 900 Q and the multiplier resistor is 708 k2, calculate the applied rms voltmeter when the voltmeter indicates FSD.
A conductor carries a current that maybe regarded as equivalent to the sum of two components, one of them being a continuous direct current of 4.2 amp and the other a superimposed half-wave rectifier current. If the latter has a maximum value of 8.3 amp, calculate the average current in the wire if (a) both components have the same direction, (b) the two components are oppositely directed?
A FW rectifier is required to deliver 48VDA with 10% ripple on a 7.5Ω resistor. a)Identify the capacitor providing these values (capacitance and ripple current - ripple current). b)Identify the necessary welding transformer for 120VAA 60Hz welding.c) Find the required serial inductance value for continuous current withdrawal from the source
2. A certain zener diode has a maximum power rating of 300 mW at 40 deg Cand a derating factor of 1.4mW/deg C. Determine the maximum power the zener can dissipate at a temperature of 80 deg C. 3. From the datasheet, a 1N4728A zener diode has a ZZ of 10 0. The datasheet gives VZ = 3.3 V at a test current, IZ, of 76 mA. What is the voltage across the zener terminals when the current is 90 mA? When the current is 45 mA?
Three-phase half wave rectifier supply resistive load with DC power of 4 kW; the ammeter connected with D1 indicates 8 A r.m.s current, and the source frequency is 50 Hz Due to system inductance the average voltage drops to 96.2% of idealized value ( when the inductance is neglected). How much will the average and r.m.s voltage s be? The r.m.s phase current and average load current Is=? & Idc=? The secondary r.m.s voltage and transformer capacity Vs & KVA? The inductances causes the voltage drop Lc=? The diode forward current and maximum inverse voltage? Now, if the phase B is failed ( disconnected), how much with new dc voltage be in %..Vdc=….% ??
A conductor carries a current that may be regarded as equivalent to the sum of two components, one of them being a continuous direct current of 4.2 amp and the other a superimposed full-wave rectifier current. If the latter has a maximum value of 6.4 amp, calculate the average current in the wire if (a) both components have the same direction, (b) the two components are oppositely directed?
Consider the full-wave rectifier circuit shown below, where• vS(t) is a sinusoidal signal with a peak value (Vs = 5 V).• Diodes are modelled using constant voltage model with VDO = 0.7 V• The ac line voltage has an rms value of 120 V and a frequency (f) = 60 Hza) Calculate the transformer turns ratio. b) Plot in the same graph signal vS(t) and the output signal vO(t) versus time (t) (show all details including amplitudes, time instances, etc.) c) Calculate the rms value of the output signal vO(t). (hint: sin2(x) = 0.5(1- cos(2x))) d) If a capacitor C=3.58 F is connected across R = 10 k, repeat (b) in a new graph