Q2) What is the maximum flow rate through the pipe shown in blow if the elevation difference of the reservoir surfaces is 80 m. and pipe friction factor is 0.024. K1= 0.5 for the pipe entrance,K2=1.0 for exit and K3= 1.0 for valve as shown in fig. * Valve (K- 1.0) Water 15'C 2000 m 80-cm-dia. concrete pipe

Q2) What is the maximum flow rate through the pipe shown in blow if the elevation difference of the reservoir surfaces is 80 m. and pipe friction factor is 0.024. K1= 0.5 for the pipe entrance,K2=1.0 for exit and K3= 1.0 for valve as shown in fig. * Valve (K- 1.0) Water 15'C 2000 m 80-cm-dia. concrete pipe

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At the gasoline transfer facility (ρᵣₑₗ=0,75) from the pond of storage to consumption, you want to install a pump to circulate a flow of 40(lt/s). The 400m long pipe is cast iron 150mm in diameter and consists of a check valve, a gate valve and 2 commercial medium radius elbows. The consumption tank is pressurized to 2,9 (kgf/cm²) gauge pressure. Decide the drive power of the pump in KW if its performance is 70%. •Additional data, pressure drop factors: •Retention valve Kᵣ = 1,5 •Gate valve open Kᵥ = 0,21 •Medium Radius Commercial Elbow Kc = 0,75 for each cubit •Storage pond outlet sharp angles Kₛ = 0,5 •Entrance to consumption pond Kₑ = 1 •Friction factor in pipes f = 0.026
In a cast-iron piping system of 450 ft length shown below, the rate of flow is 1 cfs at 70°F. Assuming the total head losses for the flow in the system is 10 ft, what is the energy head supplied by the pump E? a. 40 ft b. 50 ft c. 60 ft d. 510 ft e. None of the above
The following system is fed by a centrifugal pump. The piping is constructed from smooth plastic of OD 55 mm, wall thickness 2.5 mm. The minor losses for the system prior to the pump are given by KL = 12.0. The system curves for this pump are attached. If the flowrate is reduced to 1.4 m3/hr, and the upstream head requirement were 17 m, what would the electrical power requirement of the pump be?
Water is flowing through a pipe of 100 mm diameter under a pressure of 19.62 N/cm2 (gage) and with mean velocity of 3 m/s. find the total head of the water at a cross - section, which is 8 m above the datum line?
Paolo owns a hydroelectric power generating system as shown in HG008. Water flows from an upper reservoir to a lower one passing through a turbine at the rate of 150 lps. The total length of pipe connecting the two reservoir is 100 m. The pipe diameter is 250 mm and the Hazen – Williams coefficient is 120. The water surface elevations of reservoirs 1 and 2 are 197 m and 50 m, respectively. Find the velocity of flow in pipe in m/s.
9.7. Through a hydraulic turbine flow 2.8 m3/s of water. On the 1 m inlet pipe at elevation 43.5,a pressure gage reads 345 kPa. On the 1.5 m discharge pipe at elevation 39, a vacuum gage reads150 mm of mercury. If the total head lost through pipes and turbines between elevations 43.5and 39 is 9 m, what power may be expected from the machine?
Water at 16,2°C is to be discharged from a reservoir at a rate of 16,2 L/s using two horizontal cast iron (roughness value ɛ=0.00026m) pipes connected in series and a pump between them. The first pipe is 26,2 m long and has a 66,2 mm diameter, while the second pipe is 36,2 m long and has a 46,2 mm diameter. The water level in the reservoir is 30 m above the centerline of the pipe. The pipe entrance is sharp-edged (KL=0.562), and losses associated with the connection of the pump are negligible. Neglecting the effect of the kinetic energy correction factor, determine the required pumping head, the minimum pumping power and electric motor power for total efficiency value of 76,2% to maintain the indicated flow rate. Water density is r=996,2 kg/m3, dynamic viscosity µ= 1.162x10-3kg/ms. Solve the problem by making the necessary assumptions and drawing the schematic figure.
Suppose the pump of Fig. P14–23 is operating atfree delivery conditions. The pipe, both upstream and downstreamof the pump, has an inner diameter of 2.0 cm andnearly zero roughness. The minor loss coefficient associatedwith the sharp inlet is 0.50, each valve has a minor loss coefficientof 2.4, and each of the three elbows has a minor losscoefficient of 0.90. The contraction at the exit reduces thediameter by a factor of 0.60 (60% of the pipe diameter), andthe minor loss coefficient of the contraction is 0.15. Note thatthis minor loss coefficient is based on the average exit velocity,not the average velocity through the pipe itself. The total length of pipe is 6.7 m, and the elevation difference is (z1 - z2)= 4.6 m. Estimate the volume flow rate through this pipingsystem. Complete Answer, Thank you
Glycerin, sg = 1.26 and μ = 1.49 Pa-s, flows through a 600-mm Ø pipe at 85 liters per second. a. What is the Reynold’s Number? b. What is friction factor? c. What is the critical velocity?
The head-versus-flow-rate characteristics of a centrifugalpump are shown in Fig.. If this pump drives water at20°C through 120 m of 30-cm-diameter cast iron pipe,what will be the resulting flow rate, in m3/s?
Air @ 68°C is pumped through a pipe of internal d = 6.4in: If the vol flowrate is set to 6.2 ft3/min, is the flow laminar or turbulent? assume P is atmospheric.
Find the pressure at point 2 given the isometric drawing of the commercial steel pipeline indicating the straight pipes length and with the following data below:Loss coefficients:• check valve, k = 5.0• gate valves, k = 0.20• elbows, k = 0.75• flowmeter, k = 13.0Pump flowrate = 10 m3/hrFluid power adding by pump = 3.7 HPPressure at point 1 = 60 kPagPipe inside diameter = 50mmViscosity = 0.17 Pa.sSpecific gravity = 0.89Pipe inside surface roughness = 0.00015 ft.