Q3/ Answer the following question A 3.3 liters and 6 cylinders S.I. engine operates with a compression ratio of 7.5. Th pressure and temperature during the suction stroke are 1 bar and 25 °C, respectively. He added during the cycle is 1250 kJ/kg. Do a complete thermodynamic analysis of the idea cycle of this engine and calculate its actual efficiency.

Q3/ Answer the following question A 3.3 liters and 6 cylinders S.I. engine operates with a compression ratio of 7.5. Th pressure and temperature during the suction stroke are 1 bar and 25 °C, respectively. He added during the cycle is 1250 kJ/kg. Do a complete thermodynamic analysis of the idea cycle of this engine and calculate its actual efficiency.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

HANDWRITTEN:A vintage car has an engine that operates on an Otto cycle with a compression ratio of 8:1. Using the air standard assumption, the following parameters are applied: T2 = 720 K, T4 = 1890 K. Solve for the (a) percentage clearance, (b) volume displacement, (c) pressure and temperature at each corner, e) Heat added, (f) Heat rejected, and (g) efficiency. Note: Make sure to indicate a CORRECT P-V and T-S diagram
Interpret the engine performance based on the established parameters such as mechanical efficiency, engine efficiency and thermal efficiency and demonstrate the effect of altitude in the engine performance.
In a laboratory test of a 4-stroke engine with Vd = 3.05 liters at N = 3000 RPM the following performance data are measured: net IMEP 107.9 lbf/in2 , 70.32 brake horsepower, fuel flow rate 16.66 kg/hr., air flow rate 269.6 kg/hr. The fuel is C8H18 (QR = 4.3 x 107 J/kg.) The ambient air temperature is 295K. The intake pressure gauge is broken, so the intake pressure is not known. Determine: (d) brake thermal efficiency, (e) indicated torque, (f) Is this engine throttled, turbocharged or neither? Explain. (Hint: compute the volumetric efficiency.)
The conditions at the beginning of compression in an Otto engine are 101.3 kPaa, 0.66 m^3 and 38.0 C. If the volume at the beginning of the isometric heat addition is 0.06 m^3, what is the percent clearance?
The following are reasons why we use assumptions to represent reciprocating engines as closed system cycles, EXCEPT: a.All statementds are valid b.Reciprocating engines have equivalent thermal efficiencies as their corresponding cycles c.The shape and behavior of reciprocating engines are too complex d.The working fluid for reciprocating engines is an air-fuel mixture, which could be difficult to model
The parameters of the initial state of one kilogram of air in the cycle of an internal combustion engine are 0.095 MPa and 65 deg.C. The compression ratio is 12. Compare the values of the thermal efficiency for isobaric and isometric heat supply in the amounts of 820 kJ.
Energy balance results (in kW) obtained for the same medium speed single cylinder diesel engine are reported in the following table. For case 1, if the coolant temperature is 105 °C at the outlet of the engine and the volumetric flow rate is 0.22*10-3 m3/s, the temperature of the coolant at the inlet is (in °C): (The coolant is considered water with a density 999 kg/m3 and a specific heat 4.2 k/kg.K). Case N (rpm) bmep (bar) W. O ambient Q ahast shaft 2.2 4.2 19.1 60.3 9.90 3.52 1 500 7.1 24.5 23.8 500 6.1 3.6 5.2 400 3.50 4.9 4.1 1.4 Select one: O a. 142.1 O b. 112.7 O c. 97.31 O d. 87.2 O e. 370.31
A four-cylinder, four cycle engine with 10 cm diameter pistons and a 16 cm stroke operates at a speed of 600 rpm and yield an indicator diagram. The area under the curve (p-V diagram) is equal to 12.0 cm2. The length of the diagram is 9.0 cm, and the spring constant of the indicator spring is 600 kPa/cm. Determine the indicated power.
COMPLETE SOLUTION. FINAL ANSWER ARE IN ENGLISG SYSTEMS. DRAW A DIAGRAM IF NECESSARY. Engine XYZ is designed to be operated on the following temperature limits: 80 deg Fahrenheit and 750 deg Fahrenheit. At the beginning of the isothermal expansion the pressure is 350 psia and at the end of the isothermal expansion the pressure is 190 psig. Determine (a) the volume at the end of the isothermal compression, (b) the change of entropy during an isothermal process, (c) the heat added and the rejected, (d) the thermal efficiency, (d) the work developed in BTU/s, and (e) the mean effective pressure.
HANDWRITTEN with given, required and solution.Lycoming TIO-5XX engine is a turbocharged, fuel-injected, horizontally opposed, six-cylinder aircraft engine featuring three cylinders per side, manufactured by Lycoming Engines. Engr. Chua would like to improve the engine process changing the paddle work supplied by the turbocharger to 1,550 ft-Ibf. The experimental engine cylinder has 550 liters with an initial parameters of 3150 psf and 500 R to a final temperature of 1250 R. Consider a constant volume process. What is (a) the change in internal energy and (b) heat, if the specific heat ratio is 1.338.
in an diesel cycle temperature and pressure at the beginning of compression are 3000k and 1 bar respectively. Compression ratio is 1:6 , heat added is 2500 kJ/kg . Determine a). Temperature and pressure at the end of compression. b). Highest temperature reached in the cycle . Cp= 1KJ/kg , Cv= 0.714KJ/kg
can you include all the calculations step by step please, such as scaling law and propulsive effiency for turbojet and bypass turbojet. thank you.