Q5) A belt conveyor is used to deliver a fluid to a reservoir, see the figure. The depth of the fluid film on the belt is such that the velocity on the free liquid surface of the film is zero. By considering only the work done by the belt on the fluid in shear, find the efficiency of this device.

Q5) A belt conveyor is used to deliver a fluid to a reservoir, see the figure. The depth of the fluid film on the belt is such that the velocity on the free liquid surface of the film is zero. By considering only the work done by the belt on the fluid in shear, find the efficiency of this device.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water at a pressure of 294 3 kN/m flows through a horizontal pipe of 100 mm diameter with a velocity of 2 m/s. If the diameter of the pipe gradually reduces to 50 mm, what is the axial force on the pipe assuming no loss of energy.
AT. 2] a water pump is to be used in a water supply system as shown in the figure. The pressure at point 1 is 70 kPaa and the pressure at point 2 is 101 kPaa. The velocity in the 60-mm pipe is 2 m/s. Find the pump power. Neglect friction, and assume no change of internal energy of the water and no heat transfer between point 1 and 2. Take the density of water at standard condition. 2 m2 10 m Pump
a water pump is to be used in a water supply system as shown in the figure. The pressure at point 1 is 70 kPaa and the pressure at point 2 is 101 kPaa. The velocity in the 60-mm pipe is 2 m/s. Find the pump power. Neglect friction, and assume no change of internal energy of the water and no heat transfer between point 1 and 2. Take the density of water at standard condition.
Phy
For the tank in the figure, calculate the volumetric flow of water, which comes out through a pipe, the tank is sealed and there is a pressure of 140 KPa above the water, the depth is h1=2.5M
A tank (contains a fluid of density=1239.6 kg/m3) stands on a frictionless cart (The cart is fixed) and feeds a jet of diameter 4 cm and velocity 6 m/s, which is deflected 0=35 degree by a vane. Compute the tension in the supporting cable. 6 m/s 35 deg -D= 4 m- Do = 4 cm Cable
Fluid Mechanic Water, as seen in the figure above, is a 25° angle contractor in a piping system. With an elbow, it is directed downward in the installation with a volumetric flow of 0.025 m3 / s. Effective pressure at 1 point is measured as 2 bar. The flow is frictionless and the effects of gravity are neglected. a-)Effective pressure at point 2 b-) Elbow in place Calculate the x and y components of the force required to hold and the resultant force (pwater =1000 kg/m3, g = 9.81 m/s2)
As seen in the figure, the vacuum pump provides air flow in an insulated pipe with a cross section of 46,2 mm2. The air moves along a straight line in a room with a pressure of 100,62 kPa and a temperature of 26,2 oC. If the pressure in section 1 is 98,62 kPa and the temperature in section 2 is 16,2 oC; This is Fanno flow. i) Calculate mass flow rate, ii) Calculate at section 1, flow velocity U1, density, Mach number Ma1, Re, f values iii) Calculate at section 2, find the stopping pressure and temperature, Mach number Ma2, U2 velocity, density, mass flow rate iv) Calculate friction coefficient and force on the channel walls between section 1 and 2. Solve the problem by making the necessary assumptions. v) Calculate L1-2 pipe length Cf=0.079Re-0.25 and f=4Cf expressions can also be used. Solve the problem by making the necessary assumptions and drawing the schematic figure. (a=6 and b=2 on the figure)
1. The figure shows a pump that draws 840 L/min of crude oil (s= 0.85) in an underground storage drum to the first stage of a processing system; a) If the total energy loss in the system is 4.2 N m/N of oil flow, determine the power transmitted by the pump to the fluid. b) If the energy loss in the steel suction line is 1.4 N m/N of oil flow, determine the pressure at the pump inlet
The front and side views of a centrifugal impeller are shown in the figure below. All symbols have their usual meanings. The outer radius of the impeller is r2 = 0.4 m and the blade height the impeller outlet b₂ = 0.02 m. The volume flow rate of water (density = 1000 kg/m³) through the impeller is 0.5 m³/s. The outlet blade angle 3₂ = 35 degrees and the impeller rotational speed w=1600 rpm. Assume negligible losses, and the design conditions of whirl-free and shock-free entry. The gravitational acceleration g = 9.81 m/s². The theoretical (Euler) head is m. Front View P₂1 r2 b2- 118 Side View
For the system shown in figure, find the time required to fill the cylindrical tank (D-60cm) if. V-3m/s, Di-2cm, V-5m/s, D,-6cm, and V3-7.2m/s, Dy-5cm. h=1.2m
In the hydroelectric power plant whose cross-section is given, the flow rate of Q=33.045 m^3/sec is transmitted to the power plant through a D=1.6 meter diameter penstock. Ignoring friction losses; a) Find the internal pipe pressure at point 2 ( at the below ). b) Find the resultant force (F) and its direction (O) that the water exerts on the fixation mass. c) Calculate the electrical power generated in the plant. (Pwater= 1 ton/m^3, Ywater= 9.81 kN/m^3, g=9.81m/s^2, Beta= 45 degree