Q5 Figure Q5 shows a thick cylinder of [A] mm internal radius and [B] mm outer radius is subjected to an internal pressure of 60 MN/m² and an external pressure of 30 MN/m². Determine the hoop and radial stresses at the inside and outside of the cylinder together with the longitudinal stress if the cylinder is assumed to have closed ends using analytical and graphical approaches. Use 5th digit and 6th digit of your matrix number to get value of [A] and [B] as an example below: Example: If your matrix number is AD170128; Thus, the value of A=65 and B=160 : 5th digit of matric 6th digit of matric A B number number 50 100 1 57 1 107 65 2 115 3 72 3 122 4 80 4 130 5 87 5 137 95 6 145 102 110 117 7 7 152 8 160 167

Q5 Figure Q5 shows a thick cylinder of [A] mm internal radius and [B] mm outer radius is subjected to an internal pressure of 60 MN/m² and an external pressure of 30 MN/m². Determine the hoop and radial stresses at the inside and outside of the cylinder together with the longitudinal stress if the cylinder is assumed to have closed ends using analytical and graphical approaches. Use 5th digit and 6th digit of your matrix number to get value of [A] and [B] as an example below: Example: If your matrix number is AD170128; Thus, the value of A=65 and B=160 : 5th digit of matric 6th digit of matric A B number number 50 100 1 57 1 107 65 2 115 3 72 3 122 4 80 4 130 5 87 5 137 95 6 145 102 110 117 7 7 152 8 160 167

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Figure Q2 shows the cross-section of a closed ended thick-walled cylinder with inner radius, ri, 0.1 mand outer radius, ro, 0.2 m. The cylinder is subjected to internal pressure, pi and external pressure, po.One of the design specifications is to maintain the hoop stress at the outer surface of the cylinder at zerovalue. If po = 50 MPa and by using Lame’s equations for thick-walled cylinder, (a) determine the value of pi to achieve the design specification (b) sketch the hoop, radial, and longitudinal stress variations across the wall thickness and label their values at the inner and outer radius of the cylinder (c) determine the absolute maximum shear stress existing in the cylinder wall material
Figure Q5 shows a thick cylinder of 50 mm internal radius and 130 mm outer radius is subjected to an internal pressure of 60 MN/m2 and an external pressure of 30 MN/m2. Determine the hoop and radial stresses at the inside and outside of the cylinder together with the longitudinal stress if the cylinder is assumed to have closed ends using analytical and graphical approaches
The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the other of bronze. Neglecting the weight of the bar, compute the force (in N) in the bronze rod caused by the 42563-Nload, using the following data: length of steel = 1.56 m, length of bronze = 2.18 m Area of steel = 563 mm, Area of bronze = 233 mm Modulus of elasticity of steel = 193 Gpa, Modulus of elasticity of bronze = 82 Gpa x = 0.69 m, y = 1.03 m, and z = 0.79 m.
The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the other of bronze. Neglecting the weight of the bar, compute the force (in N) in the steel rod caused by the 43091-Nload, using the following data: length of steel = 1.36 m, length of bronze = 2.08 m Area of steel = 562 mm, Area of bronze = 243 mm Modulus of elasticity of steel = 215 Gpa, Modulus of elasticity of bronze = 102 Gpa x = 0.63 m, y = 1.01 m, and z = 0.84 m.
7.10 A rigid bar is suspended by three equally spaced wires of equal length. Theouter wires are steel and are 2 mm in diameter, the centre wire is copper andis 5 mm in diameter. If the weight of the rigid bar is 2,25 kN, calculate the loadcarried by each wire. If the temperature of the system is now raised by 90 °C, what will the magnitude and nature of the resultant stresses set up in the steeland copper wires be. (Let EST = 200 GPa; Ecu = 100 GPa; aST = 12 x 10_6/°C;acu = 18 x 10-6/°C?)
The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the other of bronze. Neglecting the weight of the bar, compute the force (in N) in the bronze rod caused by the 48512-Nload, using the following data: length of steel = 1.42 m, length of bronze = 2.36 m Area of steel = 639 mm, Area of bronze = 319 mm Modulus of elasticity of steel = 180 Gpa, Modulus of elasticity of bronze = 81 Gpa x = 0.58 m, y = 1.13 m, and z = 0.72 m. Round off the final answer to two decimal places.
Q5. A material is made in circular rod form of diameter 1.5 cm and 200mm long. It is fixed on the Universal Testing Machine. When SKN force is applied on the material, its length became 201.5 mm, material shows maximum stress 550MPa. Find [3] (1) Stress (ii) Youngs modulus (iii) Max force
A cable steel has a length of 100 m and stretch to 5 cm when the load is applied at both ends. If tensile stress is 50 psi, find the modulus of elasticity of the steel. A. 100,000 psi B. 120,000 psi C. 110,000 psi D. 130,000 psi Refer Machine Elements and Stresses Equations from the figure. Please solve the Problem elaborately. Your solution will be use as reference for my studies. Thank you so much your work will be appreciated much!
Figure Q2 shows few loadings applied on bar ABD. Suppose the diameter of the bar is 60mm,and knowing that P1 = 13kNm, P2 = 5 kNm and P3 = 12 kNm. Values A,B,C are given in TableQ2. (a) Find the following stresses at point H. (i) Normal stress due to P1 (ii) Bending stress and shear stress due to P2 (iii) Normal stress due to P (b) Determine the state of plane stress at point H and show it on the element. (c ) Using Mohr’s circle, determine the principal stresses at point H and show the result onthe element.
One spring is placed inside the other, not touching each other, and compressed between a pair of parallel plates until the distance between the plates is 40 mm. Make a neat detailed sketch of the spring and plate assembly. If G = 83 GPa for both springs, calculate the following: 1. The force applied to the spring assembly. 2. The shear stress induced in each spring. 3. The total strain energy stored in the spring assembly. 4. The stiffness of each spring. 5. The equivalent stiffness of a single spring that can be substituted in place of these springs.
In constructing a large mobile, Jude hangs an aluminum sphere of mass 6.0kg from a vertical steel wire 0.50m long and 2.5x10^−3 cm^2 in cross-sectional area. On the bottom of the sphere, he attaches a similar steel wire, from which he hangs a brass cube of mass 10.0kg. For each wire, compute: (a) The tensile strain and(b) The elongation
A rubber block with dimensions 120x120x120 mm is a rigid mold It is compressed with a vertical force of F = 120 kN inside the cavity. In the rubber block, 1-) Can you find the vertical stress (in the y direction). 2-) The shape formed in the vertical (y direction) Can you find the value of the change (mm). (Note: The mold cavity is in the shape of a prismatic box. Vertical Force F is applied in the y direction. x and z directions are closed) Rubber block, (Elasticity modulus E = 820 MPa , Poisson ratio v=0,4)