Q7: During the tension test, the wooden specimen is subjected to an average normal stress of 2 ksi. Determine the axial force P applied to the specimen. Also. find the average shear stress developed along section a-a of the specimen. ans. P =4 kips Ta 250 psi %3D 4 in. 2 in in. 4 in Q8: If the joint is subjected to an axial force of P = 9 kN, determine the average shear stress developed in each of the 6-mm diameter bolts between the plates and the members. ans. T= 79.6 MPa

Q7: During the tension test, the wooden specimen is subjected to an average normal stress of 2 ksi. Determine the axial force P applied to the specimen. Also. find the average shear stress developed along section a-a of the specimen. ans. P =4 kips Ta 250 psi %3D 4 in. 2 in in. 4 in Q8: If the joint is subjected to an axial force of P = 9 kN, determine the average shear stress developed in each of the 6-mm diameter bolts between the plates and the members. ans. T= 79.6 MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steel cable having a diameter of 0.4 in. wraps over a drum and is used to lower an elevator having a weight of 800 lb. The elevator is 150 ft below the drum and is descending at the constant rate of 2 ft>s when the drum suddenly stops. Determine the maximum stress developed in the cable when this occurs. Est = 29(103) ksi, sY = 50 ksi.
The horizontal bar shown is pinned at O and is supported with a helical springat L1 from O. L1=2m, L2=1m. The spring has 30 turns and the diameter of the wire usedis 20mm. The diameter of the spring is 125mm. Modulus of Rigidity = 83GPa. Determine the shear stress of the helical spring loaded as shown if w = 25kN/m.
Indicate the points on the stress-strain diagram which represent the proportional limit and the ultimate stress.
The block is subjected to a centrally-applied force of P=4.3 kipP=4.3 kip. Part A Determine the average normal stress on the material. Express your answer to three significant figures and include appropriate units.
A column has an outside diameter, D = 550 mm, an inner diameter, d = 150 mm.Determine the average normal stress developed on the cross section if the load, F is1890 kN.
The yield stress for a zirconium-magnesium alloy is sY = 15.3 ksi. If a machine part is made of this material and a critical point in the material is subjected to in-plane principal stresses s1 and s2 = -0.5s1, determine the magnitude of s1 that will cause yielding according to the maximum shear stress theory.
A steel pipe with an outer diameter of 50 mm and a wall thickness of 5 mm is subjected to aninternal pressure of 10 MPa and an axial load of 20 kN at an angle of 45 degrees to the axis of thepipe. Determine the maximum axial stress and maximum hoop stress developed in the pipe.
The aluminum rod AD (E=73 GPa, 0=23x10°6/°C) has a diameter of 15 mm and isattached to the rigid support at A when the temperature T; = 30°C. If thetemperature becomes T: = -20°C, and the axial loads are applied to the rod asshown, determine: a) The location and magnitude of the maximum stress acting on the rod ADb) Displacement of point Dc) Average strain in part BC
The axial assembly consists of a solid 1-in.-diameter aluminum alloy [E = 11000 ksi, v = 0.26, α= 10.5 × 10−6/°F] rod (1) and a solid 1.49-in.-diameter bronze [E = 15300 ksi, v = 0.15, α= 7.6 × 10–6/°F] rod (2). Assume L1=11 in., L2=22 in. If the supports at A and C are rigid and the assembly is stress free at 16°F, determine:(a) the normal stresses σ1, σ2 in both rods at 213°F (positive if tensile, negative if compressive).(b) the displacement uB of flange B (positive if to the right, negative to the left).(c) the change in diameter Δd1 of the aluminum rod.
The rigid bar of negligible weight is supported as shown. The middle helical spring is made of 22 mm diameter steel spring and has an outside diameter of 100 mm with 10 turns and the two side springs are made of 32 mm steel spring and has an outside diameter of 250 mm with 8 turns. Before the load P is applied, the side springs are 25 mm longer than the middle spring. If the applied load P = 15 kN and the rigid bar remains horizontal, determine the stress in each spring. Use G = 83 GPa for steel and G = 42 GPa for bronze.
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the normal stress in each rod must be limited to 107 MPa, determine the minimum diameter required for rod 1. Assume P = 80 kN and Q = 140 kN. Express your answer in mm rounded to the nearest hundredths.
The two cylindrical rod segments are fixed to the rigid walls such that there is a gap of 0.01 in. between them when T1 = 60°F. Each rod has a diameter of 1.25 in. Determine the average normal stress in each rod if T2 = 400F, and also calculate the new length of the aluminum segment. Take aal = 13(10-6)>°F, Eal = 10(103) ksi, (sY)al = 40 ksi, acu = 9.4(10-6)>°F, (sY)cu = 50 ksi, and Ecu = 15(103) ksi