Sequential circuit shown below has two flip-flops A and B and one input x. It consists of a combinatorial logic connected to the flip-flops, as shown in Figure below. Analyze the circuit: a. Derive the next state and output equations. b. The state table of the circuit. c. Draw the state diagram. A A' K 2t0-1 , MUX Y B B' CLK lo

Sequential circuit shown below has two flip-flops A and B and one input x. It consists of a combinatorial logic connected to the flip-flops, as shown in Figure below. Analyze the circuit: a. Derive the next state and output equations. b. The state table of the circuit. c. Draw the state diagram. A A' K 2t0-1 , MUX Y B B' CLK lo

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter13: Magnetic Induction

Section: Chapter Questions

Problem 1PA

See similar textbooks

Similar questions

You want to design a synchronous counter sequential logic circuit. Counting from 0 to 9 will perform and not count the numbers 0, 3, 5, 8. (a) List the steps you will apply in the design approach. State Diagram and Status Create the table. (b) Design the sequential circuit using Flip-Flops. Explain each step. Desired action show that it does.
A sequential circuit with two D flip-flops D1 and D2, two inputs x and y, and one output z is specified by the following excitation and output equations:D1 = xy¯ + xQ2D2 = xQ1 + xQ¯2z = Q1(a) Draw the logic diagram of the circuit(b) List the state table for the circuit(c) Draw the corresponding state diagram
A sequential circuit has two JK flip-flops A and B, two inputs x and y, and one output z. The flip-flop input equations and circuit output equation are attached below: a) Draw the logic diagram of the circuit. b) Derive the state equations for A and B c) Tabulate the state table. d) Draw the state diagram for the circuit and describe the function of circuit.
a) Design a logic circuit with three inputs A, B, C and an output that goes LOW only when A is HIGH while B and C are different. Draw and upload the circuit if you can, or at least describe it in words. b) Which logic gates produce a 1 output in the disabled state? c) Which logic gates pass the inverse of the input signal when these gates are enabled? d) What is the normal resting state of the SET’ and RESET’ inputs of a latch circuit (the prime is same as bar)? What is the active state of each input? e) What is the normal resting state of the NOR latch inputs? What is the active state?
(a) Construct the state table and determine the state equation of this circuit. (b) Consider the following three different approaches of implementing the sequential logic circuit Sketch the logic diagram of the circuit for each case (i) Use a negative-edge triggered D flip-flop and some primitive gates (i) Use a positive-edge triggered JK flip-flop and some primitive gates (ii) Use a positive-edge triggered T flip-flop and a 4x1 multiplexer
You want to design an arithmetic comparison combined logic circuit. (a) List the steps that you will apply in the design approach. Design a 4-bit comparison (large-equal-small) circuit. Explain each step. With AND, OR, NOT gatesmake it happen. (b)By comparing the numbers 9 and 1 in the circuit you designed, the resultdiscuss.
The question I am having trouble with is: Design a 3 bit sequential circuit using D flip flops and one input X. When X = 0 the state of thecircuit remains the same. When X = 1 the circuit goes through state transition from 0 -> 6 -> 2 ->3 -> 5 -> 0....... Make the state table, state equation and state diagram
Create a synchronous counter utilising J-K flip-flops that may be utilised for a 7-story building's elevator system, as depicted in figure below. Assume the ground floor is considered the 0th floor. Assume that level 2 and level 7 cannot be reached because they are only accessible to authorised individuals. Provide the smallest number of logic gates in the logic circuit design.
A coin-operated cold drink dispenser will provide cold drink (D) under the following conditions: The correct coin (C) is inserted AND A paper cup is in position (P) AND The selector is set t Orange (O) OR Sprite (S) OR Lemonade (L) Write the Boolean expression for the output of the dispenser. Represent the operation of the dispenser in logic circuit 4 get a logic circuit to mimic corporate checking system for operators of a company
For a sequential logic circuit that detects 010011 sequences in binary information received from an external input line x and makes external z output 1 when detected; a) Create the state diagram. Explain how you created it. b) Create the situation table. Note: D flip-flops are used in this circuit. If there are unused states in the state table, you can specify the next state values and output them as inactive values.
1. Asequential circuit with two D flip-flops A and B, two inputs, x and y ; and one output zis specified by the following next-state and output equationsA(t + 1) = xy’+ A’y‘B(t + 1) = xB+ B‘+ xB’z = A‘B(a) Draw the logic diagram of the circuit.(b) Draw the corresponding state diagram. 2.A sequential circuit has two JK flip-flops A and B and one input x . The circuit is describedby the following flip-flop input equations:JA = A‘x’+ B’KA = A’+ By’JB = A’+ xB’KB = AB+ xy’z = B‘y‘ + Bx‘y’(a) Draw the logic diagram(b) Draw the state diagram of the circuit.
Design a 3-bit synchronous counter, which counts in the sequence: 001, 011, 010, 110, 111, 101, 100 (repeat) 001, ... Draw the schematic of the design with three flip-flops and combinational logics.