Strength of Materials use p (8) KN HOME WORK 1- Stress t 14 (mm) tall 1.6 (MPa) Member B is subjected to the compressive force P. If A and B are both made of wood with thickness t, determine the smallest dimension h so that the shear stress does not exceed Tal. (P), (t) and (Tai) are given in the table below.

Strength of Materials use p (8) KN HOME WORK 1- Stress t 14 (mm) tall 1.6 (MPa) Member B is subjected to the compressive force P. If A and B are both made of wood with thickness t, determine the smallest dimension h so that the shear stress does not exceed Tal. (P), (t) and (Tai) are given in the table below.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.11P: The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in...

See similar textbooks

Similar questions

.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned supports at the ends and is 3.0 ft long. The axial forces acting at the end of the bar have a resultant P = 20 kips located at distance e = 0,75 in, from the center of the cross section. Also, the modulus of elasticity of the steel is 29,000 ksi. Determine the maximum compressive stress max, in the bar. If the allowable stress in the steel is 18,000 psi, what is the maximum permissible length Lmaxof the bar?
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
A seamless cylinder of storage capacity of 0.03m3 is subjected to an internal pressure of 21 MPa. The allowable stress in the material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder
A metal block of cross-section area A and length L is subject to a tensile stress of S. The block elongates by a length of 0.002L. Another block made from the same metal is subject to the same tensile stress. If this block has a cross-section area of 2A and a length of 2L, determine the elongation of the block.
The suspender rod is supported at its end by a fixed-connected circular diskas shown in Fig. 1–26a. If the rod passes through a 40-mm-diameter hole,determine the minimum required diameter of the rod and the minimumthickness of the disk needed to support the 20-kN load. The allowablenormal stress for the rod is sallow = 60 MPa, and the allowable shear stressfor the disk is tallow = 35 MPa.
A metal block of cross-section area A and length L is subject to a tensile stress of S. The block elongates by a length of 0.001L. Another block made from the same metal is subject to the same tensile stress. If this block has a cross-section area of 2A and a length of L, determine the elongation of the block.
If the shear modulus of a material is 120GPa & the bulk modulus is 140 GPa, then Young’s modulus is------ a. 820 GPa b. 280 Pa c. 280 GPa d. 820 Pa
The cylinder is shown in Figure is made of steel having a specific weightof gst = 490 lb>ft3. Determine the average compressive stress acting atpoints A and B.