Please refer to the image attached.Study the sheet metal assembly at the top of the image. It consists of two main parts, a flexible tube and reinforcement cap. They are attached with 4 self threading fasteners.Select datum features based on the mating condition. Make sure to note the fit between the parts.Calculate and apply position tolerances using the fastener formulas on the previous pages.Apply other necessary geometric tolerances to ensure assembly and minimize mismatch on outside edges. Workshop Exercise 15.2 - ReinforcementFlexible tubeStudy the sheet metal assembly to the left. It consistsof two main parts, a flexible tube and reinforcementcap. They are attached with 4 self threading fasteners.4X M5self threadingpan head screwsSelect datum features based on the mating condition.Make sure to note the fit between the parts.Calculate and apply position tolerances using thefastener formulas on the previous pages.ReinforcementcapApply other necessary geometric tolerances to ensureassembly and minimize mismatch on outside edges.Flexible tube4X04.8Ø50R4±0.5Ø 26.526.0Reinforcement cap6.2Ø64R3±0.5Ø5025.5P 25.015.9

Given : To find : Datum features , tolerances

Study the sheet metal assembly at the top of the image. It consists of two main parts, a flexible tube and reinforcement cap. They are attached with 4 self threading fasteners. Select datum features based on the mating condition. Make sure to note the fit between the parts. Calculate and apply position tolerances using the fastener formulas on the previous pages. Apply other necessary geometric tolerances to ensure assembly and minimize mismatch on outside edges.

Study the sheet metal assembly at the top of the image. It consists of two main parts, a flexible tube and reinforcement cap. They are attached with 4 self threading fasteners. Select datum features based on the mating condition. Make sure to note the fit between the parts. Calculate and apply position tolerances using the fastener formulas on the previous pages. Apply other necessary geometric tolerances to ensure assembly and minimize mismatch on outside edges.

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter22: Welding Joint Design And Welding Symbols

Section: Chapter Questions

Problem 4R: Sketch a V-grooved butt joint, and label all of the joint's dimensions.

See similar textbooks

Similar questions

One flange is attached to four 5x8 grade and M16 bolt connections with a total preload force of 80,000 N Calculate the factor of the bolt
You have to build a box lifter, this will be made with a square threaded power screw. The power screw is 3 inches in diameter and 2 threads per inch. To improve the speed of raising and lowering the boxes, it must be with triple thread. The coefficient of friction of the screw and collar is 0.25, the diameter of the collar is 4 inches.Calculate:1. The depth of the thread, the width of the face, the average diameter, the root diameter, the pitch and its feed.2. The torque to increase the load and the efficiency of the screw.3. The speed of the motor (in rpm), if it is directly coupled to the screw and it is desired that the boxes rise at a speed of 30 inches/min.
For Problem 2.28, ifthe block is placed at the endof thebeam, what should be the length of the steel wire inorder to regain thespacing of 1/16 in between E and B?
You have to build a box lifter, this will be made with a square threaded power screw. The power screw is 3 inches in diameter and 2 threads per inch. To improve the speed of raising and lowering the boxes, it must be with triple thread. The coefficient of friction of the screw and collar is 0.25, the diameter of the collar is 4 inches.Calculate:1. The depth of the thread, the width of the face, the average diameter, the root diameter, the pitch and its feed.
12. An ACME thread power screw has an efficiency of 70%. Determine the ratio of the lead to its mean diameter if the coefficient of friction of threads is 0.08 while the collar friction is found to be negligible.
STRENGHT OF MATERIALS (TORSION)100% GUARANTEE UPVOTE IF ANSWER IN 2 HOURSE AND 30 MINUTES.. COMPLETE SOLUTION SHORTCUT IF NECESSARY
I want proper solution don't copy from others solution I will report. flange coupling connects two 50 mm diameter lengths of commercial shafting. The coupling flanges are bolted together with four bolts of the same material as the shaft. The bolts are set in clearance holes. The diameter of the bolt circle is 240 mm and the flange thickness is 22 mm, (1) Determine the minimum bolt diameter required to transmit the same torque that the shaft can transmit.
Question 01: Draw and label any screw thread and a fastener separately. Also, discuss the types of stresses acting on screw threads and fasteners.
A double-threaded power screw is used to raise a load of 5 kN.The nominal diameter is 60 mm and the pitch is 9 mm. The threadsare Acme type and the coefficient of friction at the screw threads is0.15. Neglecting collar friction, calculate:(i) the torque required to raise the load;(ii) the torque required to lower the load; and(iii) the efficiency of the screw for lifting load.
A car jack uses a single square-thread screw to raise a known load. The major diameter and pitch of the screw and the thrust collar mean diameter are known. Running friction coefficients are estimated. Find: (a) Determine the thread depth and helix angle. (b) Estimate the starting torque for raising and lowering the load. . Schematic and Given Data: Load 50 kN
Please solve ellaborately and include the untis in every step, show diagram and write your solutions clearly and readable if your solution is in written form. Your work will be appreaciated much. Thank You! A belt drive connects two pulleys 490 mm. and 720 mm. in diameter on shafts 1240 mm. apart. Compute the length of the belt for (a) open belt drive, and (b) cross belt drive.
Using method of joints Calculate with working out, every member (Only 1/2 the sides needs to be done) - The green arrows represent 5N each downwards - and each support is a roller with 7.5N acting upwards