Date Name Industry Print Exercise 14-1 Refer to the print PR 14-1 and answer the questions below. 1. How many columns are featured in the revision history block of this drawing? 2. What is the current revision letter assigned to this part? 3. What revision specified the surface texture of the tapered portion? 4. What are the initials of the person who implemented or approved ECO 68-557? 5. Which revision specified the vendor part number of the bushing? 6. Revision F changed the maximum axial deflection to .500 at 2000 pounds. What had it been? 7. Instead of revision D, E, and F being three letters, what other method of marking could have been implemented for these three changes? Review questions based on previous units: 8. What is the thread form specified for the internal threaded holes? 9. What method was used to show external threads on this part? 10. Is this a drawing of multiple parts assembled? 11. Does this drawing feature any cutting-plane lines? 12. What is the radius of the undercut indicated by a local note? 13. What is the maximum material condition diameter of the largest cylindrical feature of this part? 14. This drawing has an italic "f" symbol on some surfaces in the left side view. What are these symbols? What does the 125 near the check mark at revision A on the tapered surface mean? 15 Inc. Unit 14 Drawing Revision Systems 299 100 114 Print supplied by Clark Equipment Company PR 14-1. ASM Silent Block Axle Mounting 4.68 4.62 2.510 2.490 2.510 2.490 1.042 1.022 1.010 066 2.312 2.252 0 ±.020 "D" "B" -12 TAPER PER FOOT GRIND OR MACHINE OPT.(A 13 64 DRILL X 45' CHAMFER BOTH ENDS BE 90 t.010 WITH MOUNTING BOSSES MIN. FLAT .75 BOTH ENDS .28 RWT HOLE MUST 125 2.68+.09 000 5.50 (2.18) (1.62) (1.41) .005 1.020 1.262 1.259 4.26 4.24 1722071 -.09 X 45 CHAMA 2.12 -ø.50 DRILL V.50 FOR ASM OPT. CONST. 1-12 UNF-2A, PD MAX. 1.0691 .92 t.020 THD LENGTH (A MIN. 1.0631 "C" "A" MUST BE FREE OF TOOL MARKS SAE 4140 LEAD ED C.R. OR STRESSPROOF -SAE-R630 BHK,Z D OR SAE-R630 BHZ A Z-DENOTESA HIGH MODULUS STOCK E WITH WEATHER RESISTANCE AND RESISTANCE TO A HYSTERESIS BUILD UP .62 MALLEABLE IRON SAE 32510 A DUCTILE 60-45-10 OPT. +.88 1.75- -18 UNF-3B, PD MAX. .5934 V.03 X 30 2 HOLES NOTE SURFACES "A" & "B" AND "C" & "D" MUST BE PARALLEL AND IN SAME PLANE DEFLECTION SPEC.: MAX. RADIAL DEFLECTION .050 AT 4000 POUNDS MAX. AXIAL DEFLECTION 500 AT 2000 POUNDS BREAK ALL SHARP CORNERS SIMILAR TO 329676 MICRO UNLESS OTHERWISE SPECIFIED MAX. INDUSTRIAL TRUCK DIVISION OR .010 CHANGES CHG. VENDORS DAYTON RUBBER CO BUSHINGS INC. NO. 3221 C DATE BY TOL. ON FIN. DIMS ALL OTHER DIMENSIONS OR DO NOT SCALE SCALE MATERIAL FILM ON CLARK EQUIPMENT CO. BATTLE CREEK, MICHIGAN NOTED ASM SILENT BLOCK 20 JAN HT. TREATMENT WAS .250 Z NOTE ADDED D WAS SAE-R-630-BHKZ 23 DEC JCS CNO. ADDED WAS 1 MIN. THD A ADDED 16 JAN JCS AXLE MOUNTING HARDNESS DRAWN FOR 13 JAN JCS ea 68-557 67-971 67-651 22 MAY DRAWN BY 16 OCT CHECKED BY 26 JUL RELEASED BY 20 THRU 50 M. BRESSON DATE DATE 12 APR DATE DATE 16 MAY MB 1722071 11 OCT MB MB RN67-393

Question

I need answers to questions 1, 2, and 3 pertaining to the print provided.

Note: A tutor keeps putting 1 question into 3 parts and wasted so many of my questions. Never had a issue before until now, please allow a different tutor to answer because I was told I am allowed 3 of these questions.

Date
Name
Industry Print Exercise 14-1
Refer to the print PR 14-1 and answer the questions below.
1. How many columns are featured in the revision history block of this drawing?
2. What is the current revision letter assigned to this part?
3. What revision specified the surface texture of the tapered portion?
4. What are the initials of the person who implemented or approved ECO 68-557?
5. Which revision specified the vendor part number of the bushing?
6. Revision F changed the maximum axial deflection to .500 at 2000 pounds. What had it been?
7. Instead of revision D, E, and F being three letters, what other method of marking could have been
implemented for these three changes?
Review questions based on previous units:
8. What is the thread form specified for the internal threaded holes?
9. What method was used to show external threads on this part?
10. Is this a drawing of multiple parts assembled?
11. Does this drawing feature any cutting-plane lines?
12. What is the radius of the undercut indicated by a local note?
13. What is the maximum material condition diameter of the largest cylindrical feature of this part?
14. This drawing has an italic "f" symbol on some surfaces in the left side view. What are these symbols?
What does the 125 near the check mark at revision A on the tapered surface mean?
15
Inc.

Image Transcription

Date Name Industry Print Exercise 14-1 Refer to the print PR 14-1 and answer the questions below. 1. How many columns are featured in the revision history block of this drawing? 2. What is the current revision letter assigned to this part? 3. What revision specified the surface texture of the tapered portion? 4. What are the initials of the person who implemented or approved ECO 68-557? 5. Which revision specified the vendor part number of the bushing? 6. Revision F changed the maximum axial deflection to .500 at 2000 pounds. What had it been? 7. Instead of revision D, E, and F being three letters, what other method of marking could have been implemented for these three changes? Review questions based on previous units: 8. What is the thread form specified for the internal threaded holes? 9. What method was used to show external threads on this part? 10. Is this a drawing of multiple parts assembled? 11. Does this drawing feature any cutting-plane lines? 12. What is the radius of the undercut indicated by a local note? 13. What is the maximum material condition diameter of the largest cylindrical feature of this part? 14. This drawing has an italic "f" symbol on some surfaces in the left side view. What are these symbols? What does the 125 near the check mark at revision A on the tapered surface mean? 15 Inc.

Unit 14 Drawing Revision Systems
299
100
114
Print supplied by Clark Equipment Company
PR 14-1. ASM Silent Block Axle Mounting
4.68
4.62
2.510
2.490
2.510
2.490
1.042
1.022
1.010
066
2.312
2.252
0
±.020
"D"
"B"
-12 TAPER PER FOOT
GRIND OR MACHINE OPT.(A
13
64 DRILL X 45' CHAMFER
BOTH ENDS
BE 90 t.010 WITH MOUNTING
BOSSES
MIN. FLAT
.75 BOTH ENDS
.28
RWT
HOLE MUST
125
2.68+.09
000
5.50
(2.18) (1.62) (1.41) .005
1.020
1.262
1.259
4.26
4.24
1722071
-.09 X 45 CHAMA
2.12
-ø.50 DRILL
V.50 FOR ASM
OPT. CONST.
1-12 UNF-2A, PD MAX. 1.0691
.92 t.020 THD LENGTH (A
MIN. 1.0631
"C"
"A"
MUST BE FREE OF TOOL MARKS
SAE 4140 LEAD ED C.R.
OR STRESSPROOF
-SAE-R630 BHK,Z D
OR SAE-R630 BHZ A
Z-DENOTESA HIGH MODULUS STOCK
E WITH WEATHER RESISTANCE AND
RESISTANCE TO A HYSTERESIS BUILD UP
.62
MALLEABLE IRON SAE 32510
A DUCTILE 60-45-10 OPT.
+.88
1.75-
-18 UNF-3B, PD MAX. .5934
V.03 X 30 2 HOLES
NOTE
SURFACES "A" & "B" AND "C" & "D" MUST
BE PARALLEL AND IN SAME PLANE
DEFLECTION SPEC.:
MAX. RADIAL DEFLECTION .050 AT 4000 POUNDS
MAX. AXIAL DEFLECTION 500 AT 2000 POUNDS
BREAK ALL SHARP CORNERS
SIMILAR TO 329676
MICRO UNLESS OTHERWISE SPECIFIED MAX. INDUSTRIAL TRUCK DIVISION
OR .010
CHANGES
CHG.
VENDORS
DAYTON RUBBER CO
BUSHINGS INC. NO. 3221 C
DATE
BY
TOL. ON FIN. DIMS
ALL OTHER DIMENSIONS OR
DO NOT SCALE
SCALE
MATERIAL
FILM
ON
CLARK EQUIPMENT CO.
BATTLE CREEK,
MICHIGAN
NOTED
ASM SILENT BLOCK
20 JAN HT. TREATMENT
WAS .250
Z NOTE ADDED
D WAS SAE-R-630-BHKZ 23 DEC JCS
CNO. ADDED
WAS 1 MIN. THD
A ADDED
16 JAN JCS
AXLE MOUNTING
HARDNESS
DRAWN FOR
13 JAN JCS
ea
68-557
67-971
67-651
22 MAY DRAWN BY
16 OCT CHECKED BY
26 JUL RELEASED BY
20 THRU 50
M. BRESSON
DATE
DATE 12 APR
DATE
DATE
16 MAY MB
1722071
11 OCT MB
MB
RN67-393

Image Transcription

Unit 14 Drawing Revision Systems 299 100 114 Print supplied by Clark Equipment Company PR 14-1. ASM Silent Block Axle Mounting 4.68 4.62 2.510 2.490 2.510 2.490 1.042 1.022 1.010 066 2.312 2.252 0 ±.020 "D" "B" -12 TAPER PER FOOT GRIND OR MACHINE OPT.(A 13 64 DRILL X 45' CHAMFER BOTH ENDS BE 90 t.010 WITH MOUNTING BOSSES MIN. FLAT .75 BOTH ENDS .28 RWT HOLE MUST 125 2.68+.09 000 5.50 (2.18) (1.62) (1.41) .005 1.020 1.262 1.259 4.26 4.24 1722071 -.09 X 45 CHAMA 2.12 -ø.50 DRILL V.50 FOR ASM OPT. CONST. 1-12 UNF-2A, PD MAX. 1.0691 .92 t.020 THD LENGTH (A MIN. 1.0631 "C" "A" MUST BE FREE OF TOOL MARKS SAE 4140 LEAD ED C.R. OR STRESSPROOF -SAE-R630 BHK,Z D OR SAE-R630 BHZ A Z-DENOTESA HIGH MODULUS STOCK E WITH WEATHER RESISTANCE AND RESISTANCE TO A HYSTERESIS BUILD UP .62 MALLEABLE IRON SAE 32510 A DUCTILE 60-45-10 OPT. +.88 1.75- -18 UNF-3B, PD MAX. .5934 V.03 X 30 2 HOLES NOTE SURFACES "A" & "B" AND "C" & "D" MUST BE PARALLEL AND IN SAME PLANE DEFLECTION SPEC.: MAX. RADIAL DEFLECTION .050 AT 4000 POUNDS MAX. AXIAL DEFLECTION 500 AT 2000 POUNDS BREAK ALL SHARP CORNERS SIMILAR TO 329676 MICRO UNLESS OTHERWISE SPECIFIED MAX. INDUSTRIAL TRUCK DIVISION OR .010 CHANGES CHG. VENDORS DAYTON RUBBER CO BUSHINGS INC. NO. 3221 C DATE BY TOL. ON FIN. DIMS ALL OTHER DIMENSIONS OR DO NOT SCALE SCALE MATERIAL FILM ON CLARK EQUIPMENT CO. BATTLE CREEK, MICHIGAN NOTED ASM SILENT BLOCK 20 JAN HT. TREATMENT WAS .250 Z NOTE ADDED D WAS SAE-R-630-BHKZ 23 DEC JCS CNO. ADDED WAS 1 MIN. THD A ADDED 16 JAN JCS AXLE MOUNTING HARDNESS DRAWN FOR 13 JAN JCS ea 68-557 67-971 67-651 22 MAY DRAWN BY 16 OCT CHECKED BY 26 JUL RELEASED BY 20 THRU 50 M. BRESSON DATE DATE 12 APR DATE DATE 16 MAY MB 1722071 11 OCT MB MB RN67-393

Expert Answer

Want to see the step-by-step answer?

Check out a sample Q&A here.

Want to see this answer and more?

Experts are waiting 24/7 to provide step-by-step solutions in as fast as 30 minutes!*

*Response times may vary by subject and question complexity. Median response time is 34 minutes for paid subscribers and may be longer for promotional offers.
Tagged in
Engineering
Mechanical Engineering

Related Mechanical Engineering Q&A

Find answers to questions asked by students like you.

Q: A 609 g eutectoid steel ( about 0.8%C) is heated to 1,002 C and cooled slowly through the eutectorid...

A: Refer to the given figure and write the expression for the amount of carbon composition in 0.8% C eu...

Q: True or False: The OFFSET command cannot be used on closed objects

A: The OFFSET command is used to create parallel lines, parallel curves and concentric circles at a cer...

Q: Consider a large plane wall of thickness L = 0.3 m, thermal conductivity k = 2.5 W/m·K, and surface ...

A: (a) Write the differential equation for one dimensional heat transfer through conduction for a slab.

Q: Acetone has a dynamic viscosity of 0.33 centipoises and a specific gravity of 0.79     ​(a) What ...

A: Calculate the density of acetone from the given specific gravity.

Q: A 0.04-m3 piston-cylinder device contains 1.4 kg of argon at 525 kPa. The piston is moved until the ...

A: a)Draw the schematic diagram for the given process.

Q: The BREAK command: a. Will work on lines and arcs b. Will work on closed objects c. Can have the sam...

A: BREAK Command is a tool in AutoCAD software which is used for removing part of an object, open or cl...

Q: 1- The energy transferred from the anterior chamber of the eye through the cornea varies considerabl...

A: Consider the system as the eye without the contact lens and observe there are three thermal resistan...

Q: A gas is contained in a vertical piston–cylinder assembly by a piston with a face area of 50 in2 and...

A: Calculate the pressure exerted by gas on the piston.

Q: True or False: You can only use the REDO command immediately after using the UNDO command.

A: The UNDO command takes back the work in a drawing session whereas the REDO command will take the wor...