Subcooled water at 5°C is pressurised to 350 kPa with no increase in temperature, and then passed through a heat exchanger where it is heated until it reaches saturated liquid-vapour state at a quality of 0.51. If the water absorbs 496 kW of heat from the heat exchanger to reach this state, calculate how many kilogrammes of water flow through the pipe in an hour. Give your answer to one decimal place.

Subcooled water at 5°C is pressurised to 350 kPa with no increase in temperature, and then passed through a heat exchanger where it is heated until it reaches saturated liquid-vapour state at a quality of 0.51. If the water absorbs 496 kW of heat from the heat exchanger to reach this state, calculate how many kilogrammes of water flow through the pipe in an hour. Give your answer to one decimal place.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Steam flows steadily through a turbine at a rate of 45,000 lbm/h. It enters at 1000 psi and 900°F and leaves at 5 psi as saturated vapor. If the power generated by the turbine is 4 MW, determine the rate of heat loss from the steam.
Refrigerant -134a at 200 kPa and 40 C flows through a refrigeration line. Determine its specific volume
Saturated liquid water at 100 kPa enters a well-insulated pump and exits at 4 MPa. Assume that the inlet and outlet temperatures are the same. How much work, in kJ/kg, is required? Report your answer to two decimal places using rounding.
Helium is used in the Carnot engine where the volumes beginning with constant temperature heat addition are V1= 0.3565 m3; V2= 0.5130 m3; V3= 8.0 m3; V4= 5.57 m3. Determine the thermal efficiency. Use 1.66 as the specific ratio of helium.
5 kg/sec of steam enters the condenser at 0.10 mpa and 88% quality. The cooling water enters @ 33C and leaves at 39C. Determine the volume flow of the cooling water in the liters per minute at the inlet
Air is compressed in a compressor through the purely polytropic, purely isothermal, and intercooling as shown in the diagram between the same pressure limits. Select the area that indicates the work saved for the intercooling process comparing to the purely polytropic one _____________ A. 1-X'-2'-P2-P1-1 B. X-X'-2-2"-X C. 1-X-X'-2-P2-P1-1 D. 1-X'-2"-P2-P1-1
Saturated liquid refrigerant 134a at 900 kPa is throttled to a pressure of 200 kPa. What is the temperature change during this process, and the final density of the refrigerant?
The water level in a tank is 70 ft above the ground. A hose is connected to the bottom of the tank, and the nozzle at the end of the hose is pointed straight up. The tank is at sea level, and the water surface is open to the atmosphere. In the line leading from the tank to the nozzle is a pump, which increases the water pressure by 15 psia. Determine the maximum height to which the water stream could rise.
Turbines, compressors, boilers, condensers, and heat exchangers operate for long periods of time under the same conditions, and they are classified as __________ flow devices.
Define the system to be a container full of steam. If the steam condenses, did the system hae a positive or negative entropy change?
A tank with an internal volume of 1 m3 contains air at 800 kPa and 25°C. A valve on the tank is opened, allowing air to escape, and the pressure inside quickly drops to 150 kPa, at which point the valve is closed. Assume there is negligible heat transfer from the tank to the air left in the tank. Using the approximation he ≈ constant = he,avg = 0.5 (h1 + h2), calculate the mass withdrawn during the process.
1m3 of an insulated rigid tank is to be charged with refrigerant R-134a. A line of saturated vapor of R-134a at 1 MPa is connected to the rigid tank through a valve. The tank is initially evacuated. The valve is then opened, and R-134a flows into the tank until the pressure in the tank is equal to that of the refrigerant line. (a) Determine the mass of R-134a in the tank, (b) Find the final temperature in the tank.