Synchronous Motor Power Correction The synchronous motor using 150-kilowatt real power so we have to find these three conditions. 1. If synchronous motor operating at 0.85 lagging power factor then what the value of transmission line? 100 kW 0.78 PF Ind. motor lagging 200 kW 0.8 PF lagging 2. If synchronous motor operating at 0.85 leading power factor then the value of current will be? lnd. Infinite bus Transmission line motor 3. If the power loss of transmission line is given. PL =31,R. Synchr. 150 KW PF=? motor Plant What will be effect of these losses on first two conditions? st 1s et ts et ts

Synchronous Motor Power Correction The synchronous motor using 150-kilowatt real power so we have to find these three conditions. 1. If synchronous motor operating at 0.85 lagging power factor then what the value of transmission line? 100 kW 0.78 PF Ind. motor lagging 200 kW 0.8 PF lagging 2. If synchronous motor operating at 0.85 leading power factor then the value of current will be? lnd. Infinite bus Transmission line motor 3. If the power loss of transmission line is given. PL =31,R. Synchr. 150 KW PF=? motor Plant What will be effect of these losses on first two conditions? st 1s et ts et ts

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.6P

See similar textbooks

Similar questions

A 25 MVA turbo-alternator is working on full load at a power factor of 0.8 and efficiency of97%. Find the quantity of cooling air required per minute at full load, assuming that 90% ofthe total losses are dissipated by the internally circulating air. The inlet air temperature is20° C and the temperature rise is 30° C. Given that specific heat of air is 0.24 and that 1 kg ofair occupies 0.8 m3.
The efficiency of a three-phase, 32 kW, 400V, 50 Hz star connected synchronous motor at full load is 90%. Synchronous impedance is 0.25 + J2 ohms. Full motor at 0.8 forward power factor with overexcitation operated at load. Accordingly, the opposite emf in the engine and the power produced by the engine Find.
A factory load consists of the following: input power of Induction motor is 40000 W at 0.76 power factor, input power of the synchronous motor is 24000 W with 0.81 power factor leading and lighting load of 10 kW at unity p.f. Find the annual electrical charges if the tariff is 390 baisa per kVA of maximum demand per annum plus 31 baisa per kWh, assuming the load to be steady for 2500 hours in a year. Annual electrical charges=______________________ Rial
MERALCO Electrician has a 25 kW series generator used in street lighting has anefficiency of 85 % when operating at rated load. If the stray power loss is 20 %of the full load loss, calculate the efficiency of the generator when delivering aload of 15 kW, assuming that the stray power loss is substantially constant andthe other losses vary as the square of the load.
A 25 MVA turbo - alternator is working on full load at a power factor of 0-8 and efficiency of 97%. Find the quantity of cooling air required per minute at full load, assuming that 90% of the total losses are dissipated by the internally circulating air. The inlet air temperature is 20 ° C and the temperature rise is 30 ° C. Given that specific heat of air is 0-24 and that 1 kg of air occupies 0-8 m3. (890 m3 / minute
The average input to a manufacturing plant is 3000 kVA at a p.f. of 0.72 lagging. A synchronous motor is to be installed for the purpose of operating a new line shaft and improving the plant power factor. With a rating of 1,300 kVA, assuming that the synchronous motor load is about 600Hp at an efficiency of 89.5% and that it is operated at rated kilovolt ampere input, calculate. a. the overall kilovolt ampere load b. the overall power factor
The power factor of a load of 400kW is 0.4 lagging. It is desired to improve this power factor to 0.7 lagging by using the over excited synchronous motor. If the synchronous motor takes 70 kW,find, 1.Power factor of synchronous motor 2.Leading kVAr of synchronous motor 3.kVA of synchronous motor.
A power plant comprises three turbine-generators rated 1000 MW, 800 MW and 600 MW respectively. The regulation constant of each generator is 0.05 pu based on its own rating. Each unit is initially operating at one-half of its own rating, when the system load suddenly increases by 250 MW. Calculate the following:a) Per-unit area frequency response characteristic on a 1000 MW system base [CR9]b) Steady-state drop in area frequency [CR4]c) The share of the load increase on each generator [CR9]d) Total load on each generator after the increase in system load [CR3]Assume the reference power setting of each turbine is unchanged.
A 489V shunt motor delivers 30hp at the shaft at 1120rpm. If the motor has an efficiency of 86% at this load, determine the (a) total input power and (b) line current.
Incremental fuel costs in dollars per megawatthour for a plant consisting of two units are given by:dC(P)/dP = 0.0080 P1 + 8.0dC(P)/dP = 0.0096 P2 + 6.4Assume that both units are operating at all times, that total load varies from 250 to 1250 MW, and that maximum and minimum loads on each unit are to be 625MW and 100MW respectively. Find the incremental fuel cost and the allocation of load between units for the minimum cost of various total loads.Write your answers in the given format below.
A 25 MVA turbo-alternator is working on full load at a power factor of 0·8 and efficiency of 97%. Find the quantity of cooling air required per minute at full load, assuming that 90% of the total losses are dissipated by the internally circulating air. The inlet air temperature is 20o C and the temperature rise is 33 30o C. Given that specific heat of air is 0·24 and that 1 kg of air occupies 0·8 m .
The data obtained in the idling test performed on a three-phase star-connected asynchronous motor; It is 1200V, 5500W, 9.5A. The data obtained in the short circuit experiment on the same motor is 250V,It is 14500W and 100A. For the case where the slip of the motor is 5%, create the approximate equivalent circuit of the motor (L type equivalent circuit), draw the equivalent circuit, find the values of the circuit elements and MUST AND MUST write them ON THE EQUIVALENT CIRCUIT. R and X values will be used in circuit elements, not Z.