Table 1: Standard Curve for Bradford Method. Absorbance measured at 595 nm Concentration of BSA Stock solution is 200 µg/mL Amount of protein in tube (ug) O ug Volume of Volume of BSA Absorbance Bradford reagent 3000 µl Cuvette no. Standard 0.00 O µl 30 µl 60 µl B 3000 µl 3000 µl 3000 µl 0.1435 1 0.2968 2 0.402 90 μι 120 µl 150 µl 0.5038 3000 µl 4 0.587 3000 µl LO

Table 1: Standard Curve for Bradford Method. Absorbance measured at 595 nm Concentration of BSA Stock solution is 200 µg/mL Amount of protein in tube (ug) O ug Volume of Volume of BSA Absorbance Bradford reagent 3000 µl Cuvette no. Standard 0.00 O µl 30 µl 60 µl B 3000 µl 3000 µl 3000 µl 0.1435 1 0.2968 2 0.402 90 μι 120 µl 150 µl 0.5038 3000 µl 4 0.587 3000 µl LO

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter8: Sampling, Standardization, And Calibration

Section: Chapter Questions

Problem 8.23QAP

See similar textbooks

Similar questions

Plot a professional quality standard curve (absorbance vs. protein amount in µg) with an appropriate title and caption underneath the plot from the data give above. The caption should include the best-fit data.
which of the folowing(s) is/are true ? 1 split ratio in GC is a ratio of sample passed to column to amount of mobile phashe 2 column resolution decreases with increasing column lenght 3 decreasing the tube diameter ,increases the resolution
The Bradford method described in the Background section was used to determine protein concentrations of known and unknown samples The following results was obtained: Table 1: Absorbance at 595nm obtained for different concentrations of protein standards using the Bradford method Protein (mg/ml) 0.00 0.125 0.25 0.50 0.75 1.00 1.50 2.00 Unknown Abs. BSA 0 0.130 0.350 0.620 0.870 1.120 1.400 1.600 0.635 Abs. BIg 0 0.080 0.230 0.460 0.520 0.410 0.510 0.700 Calculate the concentration of the unknown protein in mg/ml
A solution of Tryptophan has an absorbance at 280 nm of 0.54 in a 0.5 cm length cuvette. Given the absorbance coefficient of trp is 6.4 x 103 Lmol-1cm-1. What is the concentration of solution?
Can you please fill the rest of tghe data based on the on inforamtion you have and answer Average percent by mass of acetic acid in vinegar sample (%) ________________ Standard deviation of percent by mass of acetic acid in vinegar sample (%)
Which among the options for minimzing errors (Separation, Saturation-Mix Modification-Masking, Dilution and Matrix Matching, Internal Standard Methods, Standard Addition Methods) is most helpful with more advantages than disadvantages?
Preparing a standard curve. 1. determine the absorbance max of [FeSCN]2+ it is 448.1 2. determine the concentration of FeSCN2+ in the stock solution. M1V1=M2V2 stock solution: ~0.200 M iron (iii) nitrate in 1M nitric acid intial volume: 0.3mL final volume: 10.3mL volume: 10mL ~0.002M potassium thiocyanate initial volume: 0.3mL final volume: 10.3mL volume: 10mL not sure if this is needed stock solutions: ~0.200M iron (iii) nitrate in 1M nitric acid: 0.207M ~0.002M iron (iii) nitrate in 1M nitric acid: 0.00209M ~0.002M potassium thiocyanate: 0.00193M
You have a concentrated sample solution of a new wine from a winery to analyze for malic acid content. once you have worked up the sample and done one 5x dilution you record an absorbance of .395 at the analytical wavelength of the malic acid. the molar absorptivity coefficient E of the malic acid for this method of measurement is 15.84 mM-1cm-1. What was the molarity of malic acid in original wine sample mM?
Using the absorbance of [FeSCN]+2 at the wavelength of maximum absorption which you obtained in part B, and the diameter of the tube, obtained in part A,calculate the molar extinction coefficient. given info: Concentration of Fe3+ stock solution, C1 = 0.001 M Volume of stock Fe3+ solution pipetted, V1 = 25mL Concentration of diluted stock solution, C2 = 0.0004 M Volume of Fe2+ solution and KSCN (upon mixing) = 10mL Weight of KSCN = 1g The reaction taking place is given as: The reaction taking place is given as: F e 3+ (aq) + SC N − (aq) ⇔Fe [SCN] 2+ (aq) the concentration of [FeSCN]2+ after the mixing of Fe3+ and SCN- is 2.5 x 10-3 M. Moles of [FeSCN]2+ = 2.5 x 10-5 moles Diameter:1.2cm The wavelength at which maximum absorption takes place is = 480 nm
Use least square regression to determine the best straight line and slope; compare the slope from 5 & 6. Concentration (M) Absorbance (no units) 0.10 0.09 0.20 0.14 0.30 0.19 0.40 0.27 0.50 0.30 0.60 0.34 0.70 0.37
The absorbance of an iron thiocyanate solution containing 0.00500 mg Fe/mL was reported as 0.4900 at 540nm. Calculate the specific absorptivity including units of iron thiocyanate on the assumption that a 0.100 cm cuvette was used.
Calculate the hardness of water in ppm CaCO3 if 25.00mL of the sample required 15.00mL of a 0.1000M EDTA to reach the endpoint. (MM CaCO3= 100.09g/mol). ** Need asap pls. Thanks.