Technician A says the torque converter uses engine oil to provide a fluid link between engine and transmission. Technician B says the torque converter is attached to the engine crankshaft and receives the engine torque output. who is correct?

Technician A says the torque converter uses engine oil to provide a fluid link between engine and transmission. Technician B says the torque converter is attached to the engine crankshaft and receives the engine torque output. who is correct?

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter41: Automatic Transmissions And Transaxles

Section: Chapter Questions

Problem 7ASRQ: Technician A says that changes in engine load cause changes in hydraulic pressure inside the...

See similar textbooks

Related questions

Q: Question: How can we change the pressure valve of the hydraulic transmission system?

A: A hydraulic power transmission system uses a pressured flow to transport the energy needed to…

Q: The component used to ensure that the mainshaft (output shaft) and main (speed) gear locked to it…

A: The component used to ensure that the mainshaft (output shaft) and main (speed) gear locked to it…

Q: Which torque converter components is attached to the engine flywheel? A-impeller B-stator…

A: Main Parts of the Torque Converter are :- 1. Impeller 2. Stator 3. Turbine 4. Transmission fluid (…

Q: Technician A says when removing a transmission, the rear of the engine will usually need to be…

A: Answer

Q: echnician A says that RWD transmission valve bodies are serviceable from under the vehicle.…

Q: Technician A says that some systems use a special modulated shift control solenoid. Technician B…

A: In automobile the transmission system uses shift control solenoid which shift the gear…

Q: List all the control modes for both engine crank and engine warmup.

Q: crankshaft

A: Statement is true

Q: Carbon deposits on the intake valve or seat may cause the valve not to close properly. Tech a says…

A: If carbon deposits form on the valves or valve seats, the valves will be unable to close properly.…

Q: Technician A says that a stator aids in directing the flow of fluid from the impeller to the…

A: Technician A wrong Only Technician B correct

Q: the transfer clutch in the all-wheel-drive automatic transaxle takes the place of the _________?…

A: All-wheel drive system helps to transmit torque to all the wheels equally. As like four-wheel drive,…

Q: bull engine is the inversion which type of mechanism?

A: The bull engine is the fourth inversion of the slider-crank chain. In this type of inversion fourth…

Q: What determines whether a conventional transmission or a transaxle is used?

A: Manual transmissions feature a foot-operated clutch pedal and a shifter that allows the driver to…

Q: what allows the stator to operate correctly during vortex and rotary flow 1. the torque converter…

A: The torque converter clutch allows the stator to operate correctly during vortex and rotary flow.

Q: 58) Technician A says the vanes in each element of a torque converter are curved to increase…

A: The reason behind he curved shape of the vanesis that the air or any fluid can pass smoothly intothe…

Q: Technician A says that some systems use a special modulated shift control solenoid. Technician B…

A: Hi, thank you for the question. We’ll answer the first question since we answer only one question at…

Q: In a manual transmission what are the seven steps for power flow in final drive

A: The process of shifting the power generated by the engine toward the wheels is called the…

Q: Which component allows the vehicle to maximize engine torque? A- Torque converter B- Differential…

A: Option A is correct.

Q: An engine cranks slowly: Technician A says that a possible cause of the problem is poor starter…

A: Given that An engine cranks slowly: Technician A says that a possible cause of the problem is poor…

Q: Technician A says that the engine oil drain plug typically needs to be replaced with a new one at…

A: At every maintenance trip of the automobile engine oil is changed by removing the oil drain plug.

Q: Which type of drive system can be used designing the camshaft drive of a spark ignition engine? List…

A: given; Which type of drive system can be used designing the camshaft drive of a sparkignition…

Q: While discussing SFI systems: Technician A says that when the injection system fires according to…

A: The SFI system stands for Sequential Fuel Injection System. Within the SFI system, a specially…

Q: Technician A says hydraulic pressure affects transmission shift points. Technician B says hydraulic…

A: Affects of hydraulic Pressure : When hydraulic fluid enters into the bore of the cylinder it forces…

Q: 52) Technician A says few production vehicles have transmissions with an internal oil cooler.…

A: Technician A is saying correct statement as the transmissions with the oil cooler are located in the…

Q: Technician A says that throttle position is an important input in most electronic shift control…

A: In electronically controlled automatic transmission, the most appropriate gear ratio for the power…

Q: Add the correct numbers into text boxes to identify correct labelling of a fixed choke carburettor.

A: Given:- Fixed choke carburetor To find:- Name the parts

Q: List three possible causes of a noisy bearing during clutch operation.

A: There are many types of clutch noises such as whistling or whining, rattling noises, and many more.…

Q: What can throttle pressure be used for in automatic transmission?

A: The throttle pressure in an automatic transmission is used to control and lubricate the…

Q: airborne transmission 2. common vehicle transmission

Q: 109) A customer complains that his vehicle will not move when first shifted into gear. Technician A…

A: When the vehicle sit engine off over night, fluid from the torque converter drains back . It drain…

Q: An engine support fixture is used to hold the engine in place while removing a ______. A. fwd…

A: The fixture is a simple device used to hold the work, and sometimes it supports the work to its…

Q: 128) Technician A says slide hammer pullers are usually required to remove the front pump from the…

A: A slide hammer puller is a mechanical tool with a long round shaft. It has a hammer weight slides. A…

Q: Explain the different topic that is given. 1. what is the bleeding clutch hydraulic system 2. What…

A: Please find the solution for the first part of the question below. Also, please note that as per…

Q: Tech A says that the weight of the flywheel smoothes out the engine’s power pulses. Tech B says that…

A: Flywheel: A flywheel is a mechanical device having higher value of moment of inertia. This high…

Q: Composition of manual transmission

A: Changing aesthetic sensibilities and a demand for high performance ushered in a development in…

Q: How can we change the pressure value of the hydraulic transmission system?

A: Hydraulic power transmission systems employ a pressurized flow to transmit the energy required to…

Q: neat diagram, explain the wind turbine components such as Rotor, Drivetrain and Control System

A: The kinetic energy of wind waves when converted into electrical energy this mechanical process is…

Q: Components of torque converter

A: A torque converter is a fluid coupling used in automatic transmission for transmitting motion…

Q: Design some devices that replaces the clutch in semi or fully automatic systems and transmits engine…

A: The purpose of a clutch in an automobile is to transmit power from the engine to the transmission.…

Q: - Name the parts of the engine lubrication system shown in the figure below:

A: we are required to name the different parts of lub. system

Q: True or False? In most transmissions and transaxles,there is one synchronizer assembly for each…

A: Given Synchronizer for gear speed To find Verify the statement

Q: Technician A says that some manual transmissions use 85/90 weight gear oil or synchromesh…

A: Technician A says that some manual transmissions use 85/90 weight gear oil or synchromesh…

Q: What part is often changed with a water pump? Select one: a. A crankshaft pulley b. A timing belt

A: Generally, the idler pulleys, tensioner and water pump ought to continuously be replaced when the…

Q: A hot-wire MAF has low resistance across it when the wire is hot: Technician A says that this…

A: In a fuel injected internal combustion system the mass flow rate of air is determined by a sensor,…

Q: Some CVT transaxles do not have torque converter. What is used is its place? A. A flywhell with a…

A: Full form of CVT is Continuously Variable Transmission. In some transmission we only have fixed…

Q: Enumerate the engine auxiliary systems and briefly discuss each of their functions?

A: The auxiliary systems are - Carburetor- It is used to proper mixing of fuel and air and then…

Q: Which component is replaced by the transfer clutch in the all-wheel-drive automatic transaxle?

A: The transfer clutch in the AWD automatic transaxle takes place of interaxle differential. The…

Concept explainers

Hermetic Compressors

A compressor is a device that is used to increase the pressure of gas from low pressure to high pressure. The compressor is like a control volume, where in and out of mass occurs along with the interaction of energy with the surroundings in the form of heat and electricity.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Tech A says that the weight of the flywheel smoothes out the engine’s power pulses. Tech B says that the flexplate and torque converter perform this same function. Who is correct?
Technician A says that rotary oil flow is the oil flow around the circumference of the torque convertercaused by the rotation of the torque converter on its axis. Technician B says that the centrifugal lockup clutch is the type installed in most automatic transmissions. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
Technician A says that if a drive belt does not have the proper tension, it may produce squealing and chirping noises. Technician B says belt tension should be checked even if the engine has an automatic belt tensioner. Who is correct? Technician A Technician B Both A and B Neither A nor B
Technician A says that double-cone synchronizers have friction material on both sides of the synchronizer rings. Technician B says that multiple-cone synchronizers are used with larger engines and require a larger transmission housing. Who is correct?
Technician A says that shift solenoids direct fluid flow to and away from the apply devices in the transmission. Technician B says that shift solenoids are used to mechanically apply a friction brake or multiple-disc clutch assembly. Who is correct?
A hot-wire MAF has low resistance across it when the wire is hot: Technician A says that this condition will cause the engine to stall as soon as you put the transmission into gear. Technician B says that this condition will cause the transmission to shift late. Who is correct?
While discussing SFI systems: Technician A says that when the injection system fires according to crankshaft position and speed, it is operating in the synchronous mode. Technician B says that one of the advantages of SFI systems is that they are always in the synchronous mode. Who is correct?
when discussing shift problems, technician A says that worn or broken engine and transaxle mounts can cause a transaxle to have shifting problems. technician b says that poor shift boot alignment can cause a transaxle to jump out of gear
Which torque converter components is attached to the engine flywheel? A-impeller B-stator C-turbine D-input shaft
Technician A says that negative caster provides directional stability . Technician B says that pos caster results from excessive positive cam ber . Who is correct ?
Which of the following is probably not the cause of avibrating clutch?a. Excessive crankshaft end playb. Out-of-balance pressure plate assemblyc. Excessive flywheel runoutd. Loose flywheel bolts
Which type of transmission uses pulleys to change engine speed? Dual-dutch Manual Continuously varaible Automatic