The A913 steel rod is subjected to the loading shown with P= 14 kN. (Figure 1) The cross-sectional area of the rod is 80 mm², Neglect the size of the couplings at B and C. Figure 6kN 45° 5kN C 45 6kN 5kN 0.75 m + 1.50m Im < 1 of 1 > ▼ Part A Determine the displacement of A. Express your answer to three significant figures and include appropriate units. Submit 3.491 mm You have already submitted this answer. Enter a new answer. No credit lost. Try again. Part B Submit Determine the displacement of B Express your answer to three significant figures and include appropriate units. μÀ P Previous Answers Request Answer Provide Feedback ? C 4.366 You have already submitted this answer. Enter a new answer. No credit lost. Try again. mm ? Previous Answers Request Answer رین کیا wrong

The A913 steel rod is subjected to the loading shown with P= 14 kN. (Figure 1) The cross-sectional area of the rod is 80 mm², Neglect the size of the couplings at B and C. Figure 6kN 45° 5kN C 45 6kN 5kN 0.75 m + 1.50m Im < 1 of 1 > ▼ Part A Determine the displacement of A. Express your answer to three significant figures and include appropriate units. Submit 3.491 mm You have already submitted this answer. Enter a new answer. No credit lost. Try again. Part B Submit Determine the displacement of B Express your answer to three significant figures and include appropriate units. μÀ P Previous Answers Request Answer Provide Feedback ? C 4.366 You have already submitted this answer. Enter a new answer. No credit lost. Try again. mm ? Previous Answers Request Answer رین کیا wrong

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What is the Weibull modulus of this material? Would you advise the use of a similar material with a Weibull Modulus of 16.3 and a mean failure stress of 485 MPa, if you anticipate that the peak stress on the material could be 430 MPa? a. 15.7 b. Yes c. 18.6 d. 13.4 e. No f. 17.1
A large water tank that has a capacity to carry 20,000 liters is to be supported by four cylindrical posts. These four support posts are made of plain carbon (1045) steels with the yield and tensile strengths of 310 MPa and 565 MPa, respectively. Determine the minimum required diameter of the post assuming a factor of safety of 5.
Determine the diameter of a circular rod made of ductile material with a fatigue strength (complete stress reversal) σe = 280 MPa and a tensile yield strength of 350 MPa. The member is subjected to a varying axial load from 700 kN to – 300 kN. Assume Kt = 1.8 and F.S. = 2.
An A913 Gr. 60 W14x109 is used as a 15-m high column. The column is fixed at both ends and is laterally supported (hinged) at every one-third of its height about the weak axis. Calculate the Euler Buckling stress, Fe in MPa. Select one: a. 635.25 b. 708.09 c. 832.92 d. 653.96
The assembly below consists of a steel rod CB and an aluminium rod BA, each having a diameter of 12 mm. If the rod is subjected to the axial loadings at A and at the coupling B, determine the displacement of the coupling B and the end A. The unstretched length of each segment is shown below. Neglect the size of the connections at B and C, and assume that they are rigid. Est = 200 GPa, Eal = 70 GPa.
Two vertical steel wires each 1.5mm diameter and 1.2m long support a light rod over a span of 0.3m. A concentrated load of 250N is then applied vertically downwards at a point 0.1m from one of the wires. Determine the load, stress and extension on each wire and the angular displacement of the rod from the horizontal assuming it does not bend. Use E=200 GPa (Complete Solution)
A cylindrical pressure vessel has an inner diameter of 5 ft and a thickness of 3/4 in. The stress capacity of the pressure vessel is 25ksi. If a safety factor of 1.2 is required for the design, determine the maximum internal pressure (in psi) it can sustain. A-36 steel with the following properties: Modulus of Elasticity, E = 29x10^3 ksi or 200 GPa Shear Modulus/Modulus of Rigidity, G = 11.5x10^3 ksi or 79.3 GPa Poisson's Ratio, nu = 0.260 Temperature Coefficient for thermal expansion, a = 6.6x10^-6/°F or 11.7x10^-6/°C
A steel [E = 200 GPa] rod with a circular cross section is 13-m long. Determine the minimum diameter D required if the rod must transmit a tensile force of 23 kN without stretching more than 4 mm. 13.18 mm 28.25 mm 20.13 mm 25.90 mm 21.81 mm
A W section is used as a column of hinged ends with a length of 6 m. Fy = 248 MPa and E = 200GPa.Use the formula for combined stress. Section properties:A = 21300 mm2Sx = 2080 x 10^3 mm^3rx = 119 mmSy = 746 × 10^3 mm^3ry = 68.10 mm Questions:Determine the safe distance along the plane of the web could an eccentric load of 197.6 kN be placed. Kindly Use NSCP 2015 please for this problemHint Answers: 1,420.18
A hollow shaft is subjected to an axial load Pand a torque T, acting in the directions shown inFigure P15.9. The shaft is made of bronze [E = 105GPa;ν = 0.34], and it has an outside diameter of 55mm and an inside diameter of 45 mm. A straingage is mounted at an angle ofθ = 40° with respectto the longitudinal axis of the shaft, as shown inFigure P15.9.(a) If P = 13,000 N and T = 260 N·m, what is thestrain reading that would be expected from thegage?(b) If the strain gage gives a reading of –195 μεwhen the axial load has a magnitude of P =6,200 N, what is the magnitude of the torque Tapplied to the shaft?
The pipe assembly shown is subjected to a force F = 400 N. The pipe has an inner diameter of 20 mm and an outer diameter of 30 mm. It is made of steel with Sy = 250 MPa. Determine the safety factor at point A using the maximum shear stress theory. Select one: a. NA = 1.843 b. NA = 3.224 c. NA = 2.580 d. NA = 4.299
The rigid beam is supported by a pin at C and an A992 steel guy wire AB of length 6 ft. If the wire has a diameter of 0.2 in., determine how much it stretches when a distributed load of w = 200 lb>ft acts on the beam. The wire remains elastic.