the air gap between the crankshaft position sensor measured with and the trigger wheel is measured with an?

Q: What does the engine load sensor mean? What are the electrical lines of this sensor, explain it?

A: Engine load can be measure by a sensor which is commonly known as Mass Air Flow Sensor. It measure…

Q: What is the function of the folowing system. What is the benefit of vacuum boos Why is there a…

A: The vacuum booster is a metal canister with a diaphragm and a smart valve. On one side, a rod…

Q: explain the action of the conventional shock absorber on both compression (jouce) and rebound…

A: Shock absorbers are an important part of the suspension of a vehicle. The shock absorber is designed…

Q: Explain the Four - Stroke Cycle Engine p

A: Four strokes cycle engine can be a diesel engine or petrol engine if it is a diesel engine it has…

Q: Draw an indicator and valve-timing diagram for a 4-stroke Sl engine, label it and briefly describe.

A:

Q: Q / What is the number of crankshaft rotations during 3600 (R. P. M) in 1- Two-stroke engine 2- In…

A: Understand that the two stroke engines completes on complete cycle in one rotation 360 degrees of…

Q: B2. Explain the transducer elements with block diagram and mention the different types of…

A: The transducer comprises two imperative parts. The transducer has numerous other parts like…

Q: Explain the working of NDIR and chemical sensors of exhaust gas analyzers

A: NDIR (Nondispersive Infrared Sensors) It is a simple spectroscopic sensor that is used as the gas…

Q: Two meshing ge ocity ratio Moc I, e=2 Pressure angle

A:

Q: 360 degrees of crankshaft rotation. 1. A revolution is 720 2. The camshaft rotates degrees during…

A: To find :-  Fill in the blanks

Q: Can the rudder be manually trimmed with the autopilot engaged?* O yes No The figure below is not…

A: The rudder controls movement of the aircraft about its vertical axis .Rudder trim is done to keep…

Q: With a neat diagram ,explain about the working of Load Cell Sensor to measure the fluid Level .

A: A load cell (or loadcell) is a transducer which converts force into a measurable electrical output.…

Q: Explain with draw, how to calibrate thermocouple sensor with reader.

A: The thermocouple is a device that is used to measure high temperatures. Thermocouples are composed…

Q: Drag text boxes to label diagram of a typical valve spring retaining mechanism

A: Valve is a mechanical device that is used to to provide the passage to the inlet or exhaust of a…

Q: O) Answer the following in below; I-Explain with draw, how to calibrate thermocouple sensor with…

A: Thermocouple sensors can be calibrated using the dry block.

Q: Identify the speed sensor. a. Tachogenerator b. Diaphragm sensor c. Rotameter d. Potentiometer

A:

Q: In engine produces 10 kW brake power while working with a brake thermal efficiency of 30%. If the…

A:

Q: Tech a says that the push on the piston top during the power stroke is transferred to the crank…

A: Tech a is correct.

Q: Discuss calorific value as performance parameters on the speed of an IC engine.

A: Solution:

Q: Q/ What is the number of crankshaft rotations during 3600 (seconds or minutes) in 1- Two-stroke…

A: 1.The crankshaft is rotation in case of i.c. engine is important to complete working of all stokes.…

Q: B: The power measured by a brake attached to an engine flywheel is 4.1 brake horsepower (bhp). The…

A:

Q: How many degrees the crankshaft will rotate with both the intake and exhaust valves seated when the…

A: Calculate the degrees for which the crankshaft rotates with the intake and exhaust valve seated.…

Q: A four-stroke SI engine 0.08 m bore (d), 0.10 m stroke (L), is tested at full throttle at constant…

A: To measure the frictional power and mechanical efficiency of an engine, a Morse key test is…

Q: Tech A states to check the camshaft for lift, the cam must be removed from the engine.  Tech B says…

A: The cam is a major component of a four stroke engine which is responsible for the proper operation…

Q: The span of temperat sensor which design t

A: Given Data⇒ Temperature sensor Span

Q: e cam with reciprocating follower is driven by m volo city of F00 mrm ls nd maintains this ve

A:

Q: What provisions are usually included on tractor engines to aid in the correct timing of the…

A: A cambelt, timing chain, or timing belt is a component of the internal combustion engine of the…

Q: The power measured by a Prony brake attached to an engine flywheel is 3.8 brake horsepower (bhp).…

A: Introduction: Engine efficiency is defined as the ratio of available power to input power. The power…

Q: For a translating cam-follower system, the pressure angle should: Select one: O a. be 0° O b. be…

A: The cam and follower are a combination of two mechanical components used to utilize the rotational…

Q: A certain engine has the following specifications for valve events: IVO at 12° before HDC, IVC at…

A: b. The valve overlap diagram is as follows:

Q: What component can be used to increase the speed of pneumatic

A: solution of above problem is  belowL:

Q: (e) Out of the camber and caster, which is measured first and why? How the cambe angle can be…

A: Tire wear on the outside tread of the tyre is caused by positive camber. A car will pull to the…

Q: give 10 Troubleshooting for IC engin

A:

Q: al cup of equired to pach job f 240 cc ecificatio

A: Given: The radius of hemispherical cup is 15cm The force required to deform is 8KN. The approach…

Q: andard efficiency & brake thermal efficiency of engin

A: given:brake thermal efficiency=24.4%air thermal efficiency=53.4%

Q: 2- Draw theoretical valve timing diagram and compare it with actual one.

A:

Q: List six checks that should be carried out when inspecting camshafts

A:

Q: Explain the operation of the accelerator position sensors?

A: Principle of operation as follows. The application of alternating voltage to the transmission coil…

Q: Explain the working principle for the following sensors a) Strain gauge b) RTD c) Thermocouple

A: (a)working principle of strain gauge: srain gauge is a type of resister which senses the strain.…

Q: Out of the camber and caster, which is measured first and why? How the camber angle can be adjusted…

A: Camber angle is the angle which is measured in the front elevation in-between the wheel plane &…

Q: Note: The given below question is already fully solved just take a one review and make the schematic…

A:

Q: List out the various types of pressure sensor. Explain any one with necessary diagram.

A: .Pressure Sensors types and explanation with Diagram

Q: Explain why a small PCV valve opening is adequate atidle speed?

A: Given PCV To find Small PCV for idle speed

Q: Explanation why it is necessary to determine the mass of moving parts before analyzing and…

A: Given:The single slider crank mechanism consists of piston, cylinder,connecting rod and crank shaft.

Q: List out the design requirements of diesel engine combustion chamber

A: Diesel engines work on the diesel cycle. In diesel engines, the air is compressed alone and at the…

Q: Which one of the following is not regulating the mean speed of an engine, when there are variations…

A:

Q: he ratio Emax for the Tavg

A: we have to find out τmaxτavg