The Battery company manufactures electric batteries. The probability that the finished battery is defective is 0.05. Each battery is additionally checked by the packer. The probability that the packer finds (and removes) a faulty battery is 0.96. The probability that a packer will mistakenly remove a good battery is 0.04. Find the probability that a randomly manufactured battery will be removed by the packer.

The Battery company manufactures electric batteries. The probability that the finished battery is defective is 0.05. Each battery is additionally checked by the packer. The probability that the packer finds (and removes) a faulty battery is 0.96. The probability that a packer will mistakenly remove a good battery is 0.04. Find the probability that a randomly manufactured battery will be removed by the packer.

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter9: Current And Resistance

Section: Chapter Questions

Problem 46P: An electronic device designed to operate at any temperature in the range from 10.0C to 55.0C...

See similar textbooks

Similar questions

By measuring the currents and times and then draw the current vs time graph using the measurement at the lab for ε =8 V, R=1M Ω and C=4.7μF. When is the capasitor charged fully?
Consider three resistors; 0.5 kΩ, 5 kΩ and 7 kΩ, connected in parallel with a power supply of 5 V. Calculate the current through each resistor and hence verify the Kirchoff’s current divider rule. Write down the color codes for the following resistors: 3.4 kΩ, 10% 1 kΩ, 20% 770 Ω, 20% 2 Ω, 5% 0 Ω, 5%. Consider the 5V experimental voltmeter. Does it tend to read too high or too low voltage as compared to the standard voltmeter? Give precise reasons to support your answer.
Consider a resistor of resistivity 1.59x10^-8 ohms•m. If an electric field of 19 V/m is applied across the resistor and the electron volume concentration in the conductor is 4.7x10^28 per cubic meter, determine the drift velocity, in mm/s, of the free electron constituting the current.
. A typical smartphone Li-Ion battery has a nominal voltage of 3.7 V and is rated at 4200 mAh.Assuming the voltage remains constant a.) Compute the standby current from the battery if itlast 7 hours standby time from 100% to depletion. b.) assuming intensive gaming the phoneconsumes 1.50 A, how long will the battery last from 100% to 0%? c.) Compute the storedenergy of the fully charge battery in joules.
You measure a voltage with a multimeter, and the digital display has a constant reading of 9.0 V that does not vary over time. Which value is most reasonable to report as the random uncertainty on the measurement?
Do you think the resistor you measured are generally within tolerance? What evidence support your answer ?
Pacemakers designed for long-termuse commonly employ a lithium-iodine battery capable of supplying 0.42 A # h of charge. (a) How many coulombs of chargecan such a battery supply? (b) If the average current producedby the pacemaker is 5.6 mA, what is the expected lifetime of thedevice?
A slab of intrinsic Silicon (at room temperature) is biased, the applied electricfield inside the slab is |?⃗ | = 1.0x103 V/cm. a) What is the drift speed of the electronsb) Calculate the mean free time for electronsc) What is the average distance travelled between collisions (mean free path)d) Compare the answer in part c to the mean free path along the drift directione) What is the hole drift current density Jpd
An experiment is conducted to measure the electrical resistivityof Nichrome in the form of wires with different lengthsand cross - sectional areas. For one set of measurements, astudent uses 30.0 - gauge wire, which has a cross - sectionalarea of 7.30 x 10-8 m2. The student measures the potentialdifference across the wire and the current in the wire with avoltmeter and an ammeter, respectively. For each of the measurementsgiven in the following table taken on wires of threedifferent lengths, calculate the resistance of the wires and thecorresponding value of the resistivity. What is the average value of the resistivity, and how does thisvalue compare with the value given in Table 17.1?
Calculate the conduction velocity if the electrodes are 12cm and there are 0.3sec between the time of stimulation and the peak of the CAP.
By using spherical electrodes with the diameter D=50cm, the following breakdown voltages are measured at 18°C air temperature and 770mmHg pressure. a) If gap is equal to 7.4cm, calculate the breakdown voltage at normal conditions (20°C, 760mmHg). b) Calculate the real breakdown voltage for 1% relative measurement error (T=18°C, P=770mmHg). c) Calculate the capacitance of the electrode system with the diameter D=50cm and the gap a=7.4cm. What is the value of the resistance (R) which leads minimum 1% relative error (H) during the measurement of breakdown voltage? Çapı D=50cm olan küresel elektrotlar kullanarak 18°C sıcaklıkta ve 770mmHg hava basıncında tabloda verilen delinme gerilimleri ölçülmüştür. a) Elektrot açıklığı 7.4cm ise normal şartlar altında (20°C, 760mmHg) delinme gerilimini hesaplayınız. b) Gerçek delinme gerilimini %1 bağıl hata için hesaplayınız (T=18°C, P=770mmHg). c) D=50cm çap ve a=7.4cm elektrot açıklığına sahip elektrot sistemi için kapasite değerini…
An electric toaster uses nichrome for its heating element. When a negligibly small current passes through it, its resistance at room temperature (27.0 °C) is found to be 75.3 Ω. When the toaster is connected to a 230 V supply, the current settles, after a few seconds, to a steady value of 2.68 A. What is the steady temperature of the nichrome element? The temperature coefficient of resistance of nichrome averaged over the temperature range involved, is 1.70 × 10-4 °C-1.