The beam cross section shown in the figure below is subjected to a shear force V = 250 kN. Dimensions of the cross section are b = 150 mm, d = 210 mm, and t = 6 mm. Determine (a) The horizontal shear stress at point H, located at a = 65 mm below the upper surface of the cross section. (b) The maximum horizontal shear stress in the cross section. H d (lуp) -号一一号一 b b 2

The beam cross section shown in the figure below is subjected to a shear force V = 250 kN. Dimensions of the cross section are b = 150 mm, d = 210 mm, and t = 6 mm. Determine (a) The horizontal shear stress at point H, located at a = 65 mm below the upper surface of the cross section. (b) The maximum horizontal shear stress in the cross section. H d (lуp) -号一一号一 b b 2

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.10.10P: A hollow steel box beam has the rectangular cross section shown in the figure. Determine the maximum...

See similar textbooks

Similar questions

A wood beam reinforced by an aluminum channel section is shown in the figure. The beam has a cross section of dimensions 150 mm x 250 mm, and the channel has a uniform thickness of 6.5 mm. If the allowable stresses in the wood and aluminum are 8 M Pa and 38 M Pa, respectively, and if their moduli of elasticity are in the ratio 1 to 6, what is the maximum allowable bending moment for the beam?
A solid circular bar having diameter d is to be replaced by a rectangular tube having cross-sectional dimensions d × 2d to the median line of the cross section (see figure). Determine the required thickness tminof the tube so that the maximum shear stress in the tube will not exceed the maximum shear stress in the solid bar.
A plastic-lined steel pipe has the cross-sectional shape shown in the figure. The steel pipe has an outer diameter d1= 100 mm and an inner diameter d2= 94 mm. The plastic liner has an inner diameter d1= 82 mm. The modulus of elasticity of the steel is 75 times the modulus of the plastic. Determine the allowable bending moment Mallowif the allowable stress in the steel is 35 M Pa and in the plastic is 600 kPa. If pipe and liner diameters remain unchanged, what new value of allowable stress for the steel pipe will result in the steel pipe and plastic liner reaching their allowable stress values under the same maximum moment (i.e., a balanced design)? What is the new maximum moment?
A hollow steel box beam has the rectangular cross section shown in the figure. Determine the maximum allowable shear force K that may act on the beam if the allowable shear stress is 36 MPa. c
The cross section of a slit circular tube of constant thickness is shown in the figure, Show that the distance e from the center of the circle to the shear center S is equal to 2r in the figure part a. Find an expression for e if flanges with the same thickness as that of the tube arc added, as shown in the figure part b.
A U-shaped cross section of constant thickness is shown in the figure. Derive the following formula for the distance e from the center of the semicircle to the shear center. Also, plot a graph showing how the distance e (expressed as the non dimensional ratio e/r varies as a function of the ratio b/r. (Let b/r range from 0 to 2.)
) The internal shear force at a certain section of a steel beam is V = 8.1 kN. The beam cross-section shown in the figure has dimensions of b=137 mm, c=33 mm, d=66 mm, and t=7 mm. Determine:(c) the maximum horizontal shear stress in the cross-section. [Answer: 10.8 MPa]
The cross-sectional beam shown in the figure is subject to a maximum shear stress of 35 ksi, due to a shear force V. Determine the shear stress at points B and C, each segment of the beam has a thickness of 15mm.
The two square cross sections shown below (Figure 1) are each subjected to a vertical shear force, V. The side length of each cross section is s = 5.00 inin and the side length of the hollowed-out portion of the second cross section is r = 2.50 inin . The maximum allowable shear stress in each member is τmax = 19.0 ksi. One of the first steps in analyzing the geometry of the solid square shaft is to determine the moment of the area A’ about the neutral axis of the entire cross section. This value is denoted by Q. What is Q?(Figure 2) Answer is 15.625 in^3 A.) One of the first steps in analyzing the geometry of the hollow square shaft is to determine the moment of the area A’ about the neutral axis of the entire cross section. This value is denoted by Q. What is Q?(Figure 3) B.) Determine the maximum applicable shear force on the solid square shaft, Vmax. C.) Determine the maximum applicable shear force on the hollow square shaft, Vmax. In the image provided, figure 1 has a white slash…
Q: Shear of Thin-Walled Beams (open section 1. The figure below shows the cross section of a thin, singly symmetrical I-section. Show that the distance & of the shear center from the vertical web is given by d (1+12p) where p=d /h., The thickness is taken negligibly small in comparison with the other dimensions and fj < I,
In the figure, the boards are connected by nails to form a beam. A shear force of V= 80 kN acts on the beam. The dimensions of the plates are given as L1=200 mm, L2=150 mm and the thickness t=15 mm. The shear strength of each nail is 25 kN. Accordingly, determine the maximum spacing (s distance) between the nails.
The figure shows the cross-section of a beam that is composed of a wide-flanged structural profile, whose specification is indicated in the figure, and two steel plates, joined by means of screws, placed in pairs with a longitudinal separation of 20 cm . If the beam is subjected to a vertical shear force of 25 KN, determine the shear stress supported by each bolt in the topsheet. Please add the free diagram body.