The composite beam loaded with a triangular distributed load , consists of two aluminum alloy beams with elastic modulus Ea= 70 GPa that are bonded to a wood beam with elastic modulus Ew= 12 GPa. The design requires that the magnitude of the beams maximum deflection be no greater than (first two numbers of your student no) mm. What is the largest value of w. for which yielding of either material will not occur. FI Wo 4 m 25mm wood Aluminum 100mm 25mm 50mm 100mm

The composite beam loaded with a triangular distributed load , consists of two aluminum alloy beams with elastic modulus Ea= 70 GPa that are bonded to a wood beam with elastic modulus Ew= 12 GPa. The design requires that the magnitude of the beams maximum deflection be no greater than (first two numbers of your student no) mm. What is the largest value of w. for which yielding of either material will not occur. FI Wo 4 m 25mm wood Aluminum 100mm 25mm 50mm 100mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A simply-supported beam, 9 m in length, is subjected to a uniform load of 20 kN/m applied at the beam's middle third. Determine the maximum deflection. Answer: _____/EI
Two elastic beams with equal bending rigidity of EI are connected by a pin at B. The beam is fixed at A and a roller support is attached at C. Beam BC is subjected to a uniformly distributed load of magnitude w=1 N/m. If the bending rigidity EI is 108Nmm2, determine a) the lateral deflection at B, b) the rotational angle at B, c) the rotational angle at C. d) sketch the deformed shape
A square beam with a side of 7.6 cm has a density of 11,000 kg/m³ and is 2.4 m long. It is recessed and undergoes a load of 4000 N at 1.5 m from the recess. If its Young's modulus is 150 GPa, determine its deflection at the free end. Consider the weight of the beam. Answer: -2.67cm
The beam safely supports shear forces and bending moments of 2kN and 6.5 kN-m respectively. Based on this criterion, can it be safely subjected to the loads F = 1kN and C = 1.6 kN-m? Use the area method
A beam of 8m length rests on two supports one at the right end and the other 2m from the left end. The beam carries a udl of 15kN/m over the entire span and a concentrated load of 80kN at the middle of its span. Draw SFD and BMD . Mark all salient values and locate point of contra-flexure. Ans: RB = 120kN, MC = 172.5kNm, x1 = 0.343m from B. answer must tally with those given
A simply-supported beam, 9 m in length, is subjected to a uniform load of 20 kN/m applied at the beam's middle third. Determine the deflection at x = 7.5. Answer: _____/EI
Engineering design questions : An beam having uniform square cross section is '2' metre long supported in bearings at its ends carries a fly wheel weighing '25' kN at the centre, subjected to load which varies from 70’ N to '200' N. Determine the width and depth of a uniform square plate,. The yield strength of the materials is '850' MPa and the endurance strength '550' MPa with FOS = 2. Other correction factors may be taken as follows: For axial loading (Ka) = 0.7; For machined surface (Ksur) = 0.8 ; For size (Ksz) = 0.85 ; For stress .concentration (Kf)=1.0
Determine the equivalent stiffness of a cantilever beam which is loaded transversely on its end and has a length in 5000 mm and an annular cross section with inner and outer diameters of 25 mm and 22 mm, respectively. The modulus of elasticity of the beam is 72x109 N/m2. Use moment of inertia I=π(D4o−D4i)/64 and spring constant is (k= 500 N/m). Answer must be in three decimal places.
A cold drawn steel rod of circular cross-section is subjected to a variable bending moment of 565 Nm to 1130 N-m as the axial load varies from 4500 N to 13 500 N. The maximum bending momentoccurs at the same instant that the axial load is maximum. Determine the required diameter of the rodfor a factor of safety 2. Neglect any stress concentration and column effect. Assume the followingvalues:Ultimate strength = 550 MPaYield strength = 470 MPaSize factor = 0.85Surface finish factor = 0.89Correction factors = 1.0 for bending= 0.7 for axial load
consider the cantilevered W14 x 30 beam shown E = 29(103) ksi, I = 291 in4 determine the expression for the elastic curve using the coordinate x for 0 < x < 9 ft, where x is in feet. v in ft answer in terms of x determine the maximum slope of the beam, measured counterclockwise from the positive x axis. Theta max in rad. determine the maximum deflection of the beam. Vmax in ft.
A 25 mm wide and 100 mm deep beam is 3.4 m long. It carriesa load of 1500 kN at the middle. Determine the maximum stressdue to bending. and find the Young’s modulus of the material usedfor the beam if it is deflect 2500 mm maximum at the mid of thespan.
The beam is made of southern pine for which Ep = 13 GPa. Determine the displacement at A.