-The connection shown in the figure if the screw is type 98 and the two plates are A'SI 1040 CD stee, the highest tensile strength that can be shed longtudnally so that the safety factor is nct less than 2 5 The following possibalities of failure E- Shearing the bolts b-Loading the bolts - Loading into the member. item I tensile in the element M24x3 40 so 40 25 -100--

-The connection shown in the figure if the screw is type 98 and the two plates are A'SI 1040 CD stee, the highest tensile strength that can be shed longtudnally so that the safety factor is nct less than 2 5 The following possibalities of failure E- Shearing the bolts b-Loading the bolts - Loading into the member. item I tensile in the element M24x3 40 so 40 25 -100--

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.1P: A rigid bar of length L is supported by a linear elastic rotational spring with rotational stiffness...

See similar textbooks

Similar questions

The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
Which of the following is the design stress for a piston rod where the axial load is completely reversed if the surface of the rod is ground and the surface finish factor is 0.9? Assume no stress concentration. Use a factor of safety of 2 and an endurance limit of 250 MPa. The load factor for completely reversed axial load is 0.85.
In the state of loading as made of brittle material tensile and compression fracture values of the exposed arm, respectively. σUT=200 MPa and σUC=800 MPa and factor of safety n=4 as it is; a) First reduce the applied forces to point B, b) By determining the critical point of the critical section and stresses Calculate it and show it on the stress element. c) Calculate the diameter of the AB part according to the Coulomb criterion. Note: Neglect the effect of cutting forces.
The piston rod of an air operated press has a length of 2500 mm, with its right-hand end pin connected to the operating lever and the piston end of the rod fix ended. The rod is made of a material whose Sy = 250 MPa and E = 200 GPa. For a factor of safety of 3.5, determine the maximum safe compressive load of the rod in Newtons if its diameter is 47.5 mm. Round your answer to 4 significant figures.
A hollow, short compression member, of normalized cast steel (ASTM A27-58, 65 ksi), is to support a load of 1500 kips with a factor of safety of 8 based on the ultimate strength. Determine the outside and inside diameters if Do = 2Di
Calculate the maximum stress in the steel ring if a copper ring with a thread diameter of 2000 mm and a thickness of 20 mm and a steel ring with an inner diameter of 2000 mm and a thickness of 10 mm are interlocked and heated to 100°C. Scale= 100 GPa, Eçelik= 200 GPa, copper= 16.106/°C, steel= 12.10-6/°C a-) 20 MPa b-) 40 MPa c-) 50MPa d-) 60 MPa e-) 30 MPa
Material P is suggested to be used as a rod with the applied stress up to 300 Material P has a yield strength of 290 MPa and the safety factor is 2. Interpret with ONE (1) reason whether this material can be used for the desired application.
A round cross-sectional bar d= 39 mm is cut from steel of Sut = 715 MPa. The bar is loaded with a completely reversed stresses. What is the strength of failure (in MPa) If only 10 4 cycles are needed? (Take fully corrected Se = 358 MPa, no need to use modification fcactors) (accepted answer range +/- 5 MPa)
A 30-mm thick AISI 1020 steel plate is sandwiched between two 20-mm thick2024-T3 aluminum plates and compressed with a bolt and nut with no washers. The boltis M12 × 1.75, property class 9.8. Draw a sketch of the joint and,(a) Determine a suitable length for the bolt, rounded up to the nearest 5 mm. (b) Determine the bolt stiffness.(c) Determine the stiffness of the members and joint stiffness.
The rigid pipe is supported by a pin at A and an A-36 guy wire BD ( E = 29 000 ksi). If the end C is displaced 0.75 in. downward when P is applied. What is the required diameter of the guy wire in inches to support the load P = 44 kips?
(6) A wall bracket is loaded so that the two top bolts that fastened it to the wall are subjected to a tensile load of 1,420lbs. The bolts are to be C1020 (Sy = 48ksi) steel with coarse threads. Neglecting the effect of shearing stress, determine the size of the bolts to be used if they are well-tightened.
If the ultimate stress for a material is 250 MPa. Then the allowed working stress is _______MPa, if the factor of safety is considered to be 2 Select one: a. 8 b. 125 c. 500 d. 8 x 10-3