The following rod has a diameter of 15 mm, and a length of 1000 mm, and was fixed at its one end to the wall. A force pair of 200 N is applied by a 500 mm length arm to the point A. Which material given below should be chosen for this rod material to keep the twist angle on the A plane less than 20°.

The following rod has a diameter of 15 mm, and a length of 1000 mm, and was fixed at its one end to the wall. A force pair of 200 N is applied by a 500 mm length arm to the point A. Which material given below should be chosen for this rod material to keep the twist angle on the A plane less than 20°.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The solid-circular member AC, having a diameter D and a shear modulus of 69 GPa, is subjected to the torques 2T and 3T at points A and B, respectively. If tallow = 35 MPa and (fA/C)allow =2o, determine the maximum permissible value of the torque T. Use the table given below and your student ID to find the values of L1, L2, and D. Student ID L1 (m) L2 (m) D (mm) 1131731 1 0.6 78
the Am1004-T61 magnesium tube is bonded to the A-36 steel rod. the allowable shear stresses for the magnesium and steel are (allow)mg = 45MPa and (allow)st=84 MPa, respectively. the shear modulus of elasticity for Am1004-T61 magnesium alloy is 18 GPa and for A-36 steel is 75 GPa determine the maximum allowable torque that can be applied to A (see attached jpg file) find the corresponding angle of twist of end A
Torsion A hollow circular shaft has inside and outside diameters of 30 mm and 40 mm respectively. The material has-a shear modulus of 60 kN/mm'. Determine the maximum stress in the shaft when it is subjected to a twist of 5 in a length of 2.5 m. What is the maximum torque the shaft can carry? For a circle / = nd*/32.
A 2in diameter shaft is made of aluminum 2014-T6, and has a torque of 1/2T, -T and 2/3T respectively along its length measured from the free end with the distance of 12 inches between its section. If the factor of safety of 3 is used and the angle of twist is limited such that it does not exceed 0.1 rad. find the maximum allowable tonque T in the shaft in ksi
The Am1004-T61 magnesium tube is bonded to the A-36 steel rod. the allowable shear stresses for the magnesium and steel sre Tallow mg =45Mpa ve Tallow st=72MPa, respectively. The shear modulus of elasticity for Am1004-T61magnesium alloy is 18Gpa and for A-36 steel is 75Gpa. a)Determine the maximum allowable torque that can be applied at A. b)Find the corresponding angle of twist of end A.
The shaft (G = 80 GPa) has a diameter of 14 mm, determine the angle of twist at B. Also draw free body diagram
The connecting rod of a four stroke cycle Diesel engineis of circular section and of length 550 mm. The diameter and stroke of the cylinder are 150 mm and240 mm respectively. The maximum combustion pressure is 4.7 N/mm2. Determine the diameter ofthe rod to be used, for a factor of safety of 3 with a material having a yield point of 330 MPa.Find also the maximum bending stress in the connecting rod due to whipping action if the engine runsat 1000 r.p.m. The specific weight of the material is 7800 kg/m3. [Ans. 33.2 mm ; 48 MPa]
The aluminum alloy [G = 4000 ksi] pipe is fixed to the wall support at C. The bolt holes in the flange at A were supposed to align with mating holes in the wall support; however, an angular misaligment of 4° was found to exist. To connect the pipe to its supports, a temporary installation torque T'B must be applied to B to align flange A with the mating holes in the wall support. The outside diameter of the pipe is 5.5625 in. and its wall thickness is 0.258 in. The segment lengths are L1= 16 ft and L2 = 24 ft. a) Determine the temportary installation torque T'B that must be applied to B to align the bolt holes at A b) Determine the maximum shear stress τinitial in the pipe after the bolts are connected and the temporary installation torque at B removed c)Determine the magnitude of the maximum shear stress in segment (1) and (2) if an external torque TB= 150 kip-in. is applied at B after the bolts are connected
If the shaft is made of red brass C83400 copper with an allowable shear stress of ?allow = 20 MPa, determine the maximum allowable torques T1 and T2 that can be applied on A and B. Also, find the corresponding angle of twist of end A. Set L = 0.75 m "Mechanics of Materials, Hibbeler"
The flywheel causes a completely reverse bending on the shaft and the factor of safety is 2, determine: a. The ultimate tensile strength ( Su) of the material if the Yield strength (Sy) is 0.6 of Ultimate strength. b. The fatigue life of the shaft given the fatigue strength (S) is equal to 0.8Su and endurance Strength (Se) is equal to 0, 5Su, given the minimum stress is 0.3 of Maximum stress c. Draw the S - N diagram
The flywheel causes a completely reverse bending on the shaft and the factor of safety is 2, determine: a. The ultimate tensile strength (Su) of the material if the Yield strength (Sy) is 0.6 of Ultimate strength. b. The fatigue life of the shaft given the fatigue strength (Sf) is equal to 0.8 Su and endurance Strength (Se) is equal to 0,5 Su, given the minimum stress is 0.3 of Maximum stress c. Draw the S-N diagram
A solid steel post is subjected to pure torsion. Given: -post Diameter = 65 mm -length = 2.75 m -torque = 2.4 kN-m -shear Modulus of Elasticity = 78 GPa Question: What is the Angle of Twist in degrees?