The illustrated truss is subject to certain loads. Calculate the forces acting in the components identified as 3-4, 3-10, and 9-10. Attach your solution (Give, Required, Solution with FBD) 1.6 kips 0.8 kip 1.6 kips 23. 8 ft 1.6 kips 8 8 ft 9 4 8 ft 10 1.6 kips 5 8 ft 1/1 + 1.6 kips 8 ft 6- 12 0.8 kip 6 ft 7 14.5 ft d 8 ft

The illustrated truss is subject to certain loads. Calculate the forces acting in the components identified as 3-4, 3-10, and 9-10. Attach your solution (Give, Required, Solution with FBD) 1.6 kips 0.8 kip 1.6 kips 23. 8 ft 1.6 kips 8 8 ft 9 4 8 ft 10 1.6 kips 5 8 ft 1/1 + 1.6 kips 8 ft 6- 12 0.8 kip 6 ft 7 14.5 ft d 8 ft

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.1P: A 10-ft rigid bar AB is supported with a vertical translational spring at A and a pin at B. The bar...

See similar textbooks

Similar questions

A long re Lai nine: wall is braced by wood shores set at an angle of 30° and supported by concrete thrust blocks, as shown in the first part of the figure. The shores are evenly spaced at 3 m apart. For analysis purposes, the wall and shores are idealized as shown in the second part of the figure. Note that the base of the wall and both ends of the shores are assumed to be pinned. The pressure of the soil against the wall is assumed to be triangularly distributed, and the resultant force acting on a 3-meter length of the walls is F = 190 kN. If each shore has a 150 mm X 150 mm square cross section, what is the compressive stress
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
A 10-ft rigid bar AB is supported with a vertical translational spring at A and a pin at B. The bar is subjected to a linearly varying distributed load with maximum intensity q0. Calculate the vertical deform at ion of the spring if the spring constant is 4 kips/in.
A lifeboat hangs from two ship's davits. as shown in the figure. A pin of diameter d = 0.80 in. passes through each davit and supports two pulleys. are on each side of the davit. Cables attached to the lifeboat pass over the pulleys and wind around winches that raise and lower the lifeboat. The lower parts of the cables are vertical and the upper parts make an angle a =15° with the horizontal. The allowable tensile force in each cable is 1800 lb, and the allowable shear stress in the pins is 4000 psi. If the lifeboat weighs 1500 lb, what is the maximum weight that can be carried in the lifeboat?
Solve Problem 11.3-3 for a W 10 × 45 steel column having a length L = 28 ft.
An idealized column is composed of rigid bars ABC and CD joined by an elastic connection with rotational stiffness ßRIat C. There is a roller support at B and an elastic support at D with translationa1 spring stiffness ß and rotational stiffness ßR2. Find the critical buckling loads for each of the two buckling modes of the column. Assume that L = 3 m, ß = 9 kN/m, and ßR]= ßR1= ßL2. Sketch the buckled mode shapes.
Consider the plane truss with a pin support at joint 3 and a crtica1 roller support at joint 5 (see figure). (a) Find reactions at support joints 3 and 5. (b) Find axial forces in truss members 11 and 13.
An idealized column is made up of rigid bars ABC and CD that are joined by a rotational elastic connection at C with stiffness ßR. The column has a roller support at B and a pin support at D. Find an expression for the critical load Pcr of the column.
SITUATION 2: A two-member frame in the figure is loaded as shown in Fig. MEC-121. Calculate the equivalent force (kN) of the distributed load. (Answer: 6) Calculate the y-component of the reaction at B (in kN). (Answer: 3) Calculate the magnitude of the reaction at A (kN). (Answer: 13.63) and the magnitude of the reaction at C (kN). (Answer:14.97)
PROBLEM: Determine the forces in each member using any methoddiscussed in your theory of structures/mechanics. Using Software is notallowed. Show complete solution and tabulate your answers indicatingwhether it is compression or tension. Use Pn = 205 kN, Po = Zero. a) From the Problem and the image , Design one tension member, use either a double angle of a wt section. Check its adequacy using 1 line of bolts (three bolts in a line spaced at 75mm on centers) Assume a bolt diameter from 16-22mm. Use A 36 for all steel. Neglect block shear.
Pin jointed frame is subjected to the external loads of F6 = 2733 N at D and F7= 1938 N at C as shown in Figure T2. Take the length of frames indicated as: L6 = 2964 mm and L7= 6164 mm.(i). Draw the free body diagram of the given Frame/Truss;(ii). Estimate the support reactions;(iii). Determine the forces in all members indicating the nature of forces; (iv). Verify the forces in members AD and AE by another suitable method.
L₁ B 7 B D -‒‒‒‒‒‒‒‒‒‒‒‒‒‒‒‒‒‒‒‒‒‒‒ T Figure 1. Boom of a crane supporting load T. The boom of the crane ABC shown in Figure 1 is pin supported at A. The hydraulic support BD can be assumed as a two-force member. It carries load only along its axis. Calculate the reaction forces at the pin support and the reaction force exerted by BD on the boom. The data required to solve the problem are: L₁ 4.5 m, L₂ = 4 m, a = 60°, B = 50° and T = 34 kN. =