Determine the state of stress at point A on the cross section of the pipe assembly at section a-a. Take F₁ = 1520 N, F₂ = 1100 N. (Figure 1) Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive in the case of tension.

Determine the state of stress at point A on the cross section of the pipe assembly at section a-a. Take F₁ = 1520 N, F₂ = 1100 N. (Figure 1) Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive in the case of tension.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The diameter of the pressure vessel is 450 mm, and its length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa, and the circumferential stress is limited to 60 MPa.
Do the principal stresses represent the maximum and minimum normal stress?
A thick cylinder is built up by shrinking an aluminium tube 20mm thick upon a hollow aluminium cylinder having an outside diameter 150mm and inside diameter 100mm thereby causing a contact pressure of 20MPa. What is the largest internal pressure that can be applied to the assembly without exceeding a tangential stress of 100MPa at the inner surface. Ans: Pi = 97.5MPa answers must tally
mechanics of deformable bodies The cylindrical tank has an outer radius of 1.5m and a wall thickness of 25 mm. If the tank is pressurized to 1.5 MPa, determine the longitudinal stress.
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 30 mm. The outer diamter and thickness of the pressure vessel is 500 mm and 10 mm. Its length is 2m. Determine the maximum internal pressure (MPa) that can be applied if the longitudinal stress is limited to 155 MPa, and the circumferencial stress is limited to 55 MPa.
Explain the method of representing the combination of normal and shear stresses acting on any plane through an incremental element on shear stress–normal stress coordinates.
1. A cylinder tankhas a maximum load of 2600 kg while the pressure is 2600 kpa. If the ultimate stress is 55 000 kpa and a factor of safety is 4.5, calculate the required wall thickness of the cylinder. Choose the correct answer below and show complete solution: a. 18.34 mm b. 14.38 mm c. 13.48 mm d. NOTC 2. A spherical tank has a diameter of 12 m, if the tangential stress of the tank is 18 Mpa, determine the maximum internal pressure of the tank can carry if the wall thickness is 25 cm. Choose the correct answer below and show complete solution: a. 150 kPa b. 15000 kPa c. 1500 kPa d. NOTC 3. A cylindrical tank has an inside diameter of 6-in and is subjected to an internal pressure of 600 psi. If the maximum stress is 1300 psi, calculate the required thickness. Choose the correct answer below and show complete solution: a. 0.1385 in. b. 0.3185 c. 0.8135 d. NOTC
1.A cylindrical pressure vessel is 500 mm in diameter and has a wall thickness of 22 mm. If it is subjected to an internal pressure of 5 MPa, determine the tangential and longitudinal stresses developed in the cylinder.
Indicate the points on the stress-strain diagram which represent the proportional limit and the ultimate stress.
Question 1A thick-walled tube with the outer and inner diameter of 360 and 180 mm, respectively is subjected to an external pressure of 25 MPa. Assuming the open-ends condition of the tube:(a) Determine the hoop stress component at the outer wall of the tube.(b) The hoop stress in part (a) can be neutralized (zero magnitudes) by filling the tube with fluid. Determine the required magnitude of the fluid pressure in the tube to achieve this condition.(c) Compare the variations of the hoop stress and radial stress across the wall thickness of the tube for part (b). Indicate the stress values at the inner and outer radii of the tube.
A 12cm x 16cm air compressor is operated with a maximum pressure of 10 kg/cm2. There are5 bolts with a yield value of 64ksi holding the cylinder head to the compressor. Determine the tensile stress of the bolt.
A seamless cylinder of storage capacity of 0.03m3 is subjected to an internal pressure of 21 MPa. The allowable stress in the material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder.8mm A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder.540mm