The solid circular rod has a cross-sectional area of 470 mm². It is subjected to a uniform axial distributed loading along its length of w= 8 kN/m. Two concentrated loads also act on the rod: P = 5 kN and Q = 7 kN. Determine the normal stress in the rod at x = 1.4 m. Assume a = 0.5 m and b = 1.2 m.

The solid circular rod has a cross-sectional area of 470 mm². It is subjected to a uniform axial distributed loading along its length of w= 8 kN/m. Two concentrated loads also act on the rod: P = 5 kN and Q = 7 kN. Determine the normal stress in the rod at x = 1.4 m. Assume a = 0.5 m and b = 1.2 m.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The rectangular bar has a width of w = 3.25 in. and a thickness of t = 2.00 in. The normal stress on plane AB of the rectangular block shown is 6 ksi (C) when the load P is applied. Assume a = 4 and b = 5. Determine the maximum normal stress in the block at any possible orientation.
The solid 0.85-in.-diameter rod is subjected to a uniform axial distributed loading along its length of w = 500 lb/ft. Two concentrated loads also act on the rod: P = 1900 lb and Q = 900 lb. Assume a = 12 in. and b = 24 in. Determine the normal stress in the rod at the following locations: (a) x = 8 in. (b) x = 24 in.
The three suspender bars AB, CD, and EF are made of A-36 steel (E = 250 MPa) and have equal cross-sectional areas of 400 mm2. Determine the average normal stress in each bar if the rigid beam is subjected to a force of P = 80 kN. Let d = 3 m and L = 8 m
The 10-mm-diameter steel bolt is surrounded by a bronze sleeve. The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. If the bolt is subjected to a compressive force of P = 20 kN, determine the average normal stress in the steel and the bronze. Est = 200 GPa, Ebr = 100 GPa.
The compound wooden beam is connected together by a bolt at B. Assuming that the connections at A, B, C, and D exert only vertical forces on the beam, determine the required diameter of the bolt at B and the required outer diameter of its washers if the allowable tensile stress for the bolt is 1st2allow = 150 MPa and the allowable bearing stress for the wood is 1sb2allow = 28 MPa. Assume that the hole in the washers has the same diameter as the bolt.
Determine the maximum compressive stress in the bracket at section a-a when the load P = 70 kN is applied at x = 0.
433 The steel pipe is filled with concrete and subjected 10 a compressive force of 80 kN. Determine the averaee normal stress in the concrete and the steel due to this loading. The pipe has an outer diameter of 80 mm and oo inner diameter of 70 mm. E, = 200 GPa, E. = 24 GPa.
The singular force F will be applied to the beam with a hollow rectangular cross section. Accordingly, the location and value of the maximum normal stress that will occur in the whole beam is given correctly in the following? F =400 N, L1 = 3m, L2 = 2m, h1=48mm, h2 =72mm, b1=10mm, b2=20mm
The bar has a cross-sectional areao of 490(10-6)m2. It is subjected to triangular axial distributed loading along its length which is 0 at x= 0 and 9 kN/m at x= 1.5 , and to two concetrated loads Determine the average normal stress in the bar as a function of x for 0 <_x < 0.6m
The cross-sectional area of the bar ABCD is 600 mm². Determine the maximum normal stress in the bar?
The rigid beam BDF is supported by three steel bars each having a cross-section area of 6Y mm2 . Determine the normal stress in each bar. ? = 200 ??a x=6 y=3 L=5 z=7.
The center post B of the assembly has an original length of 123 mm, whereas posts A and C have a length of 127 mm. If the caps on the top and bottom can be considered rigid, determine the average normal stress (in MPa) post A. The posts are made of aluminum and have a cross-sectional area of 423 mm2 Ealuminum = 70 GPa.