Kindly solve this your help will be appreciated I will give you good ratings The inlet and throat diameters of a horizontal venturimeter are 30 cm and 10 cmrespectively. The liquid flowing through the meter is water. The pressure intensity atinlet is 13.734 N/cm² while the vacuum pressure head at the throat is 37 cm ofmercury.a) Calculate the rate of flow, assume that 4% of the differential head is lostbetween the inlet and throat.b) Calculate the value of Ca for the venturimeter.

Answered: Image /qna-images/answer/b2ee1790-845b-45ae-981c-9369592796dc.jpg

Answered: The inlet and throat diameters of a…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If the difference between the total pressure and static pressure in an air duct is measured by a pitot tube to be 6.5 cm H2O, what is the flow velocity in m/s? Density of water is 998 kg/m3, and g = 9.81 m/s2. 3 signififcant figures answer
A pipe discharges 142 lps of water into a reservoir at a point 1.85 mbelow the water surface. At point A the diameter is 25.4 cm and the center of thepipe is 1.25 m above the water surface. At the discharge end the pipe is 30.5 cm.If the head loss from A to the reservoir is 0.7 m, determine the pressure in A.
When a pump with a suction and discharge pressure of 125 kPa and 409 kPa are used, the flow rate is 30L/s into a pipe with a diameter of 4 cm. Approximately 10cm in diameter, the suction diameter. What is the energy added to the water by the pump in meters
When a pump with a suction and discharge pressure of 125 kPa and 409 kPa are used, the flow rate is 30L/s into a pipe with a diameter of 4 cm. Approximately 10cm in diameter, the suction diameter. What the mechanical efficiency of the pump (in percent) if the power input recorded is 27.34 hp
A two storey building has two faucets, one in the basement and one in the firstfloor. The maximum water (ρ = 1000 kg/m3) velocity at the basement faucet, when the first floor faucet is closed, is 13 m/s. The faucet diameter is 1.5 cm.Neglect all losses. What would be a maximum height (from the basement floor) for a faucet,to still get a maximum exit velocity of 6 m/s?
Two vertical tanks, one with circular section 3.0 m in diameter, the other square section 1.33 m x 1.33 m are connected by a short tube ( area is 0.725 sq. cm) near bottom. Initially, the head of oil in the first tank is 4.0 m, while in the second tank the head is 60 cm. After a quick opening of the tube's vlave, find the time for the oil surfaces to equalize. Assume the tube properties to be similar to that orifice, with C= 0.78.CHOICES: a.26 seconds b.23 seconds c.21 seconds d.35 seconds
Two vertical tanks, one with circular section 3.0 m in diameter, the other square section 1.33 m x 1.33 m are connected by a short tube ( area is 0.725 sq. cm) near bottom. Initially, the head of oil in the first tank is 4.0 m, while in the second tank the head is 60 cm. After a quick opening of the tube's vlave, find the time for the oil surfaces to equalize. Assume the tube properties to be similar to that orifice, with C= 0.78.
ME Board - October 2002 Water is to be raised to a height of 25 meters at 20 kg/s. Inlet diameter is 16 cm, exit diameter is 12 cm and heat loss is 2 kW. Determine the power input to the pump.
Water is being drained through a hole at the bottom of a tank at a velocity of 10 m/s. For a tank diameter of 1.18 m and a hole diameter of 5 cm, find the rate of change of the water level in the tank in m/hr.
The inlet and throat diameters of a horizontal venturimeter are 30 cm and 10 cm respectively. The liquid flowing through the venturimeter is water. The Pressure intensity at inlet is 13.734 N/cm² while the vacuum pressure head at the throat is 37 cm of mercury. Find the rate of flow. Assume that 4% of the differential head is lost between the inlet and throat. Find also the value of Ca for the venturimeter.
A cubical reservoir(3.5mx3.5mx3.5m) is being filled with gasoline (SG=0.72) through section 1 with 950 litre/m and through section 2 with velocity of 5cm/s, and exit at Section 3 at 15cm/s. The diameter of the round pipe at section 2 is 35mm and section 3 is 50mm. i) Determine the rate of increment/decrement h(m/s) ii) Determine time taken to fill up the reservoir from empty, if section 3 is closed. iii) Determine the rate of increment/decrement h(m/s), if the flow at flow rate at Section 1 is halved, Section 2 changes direction, and Section 3 is closed.
Read the question carefully and give me all right solutios. A 2.4 m diameter tank is initially filled with water 5.5 m above the center of a 10 cm diameter, sharp-edged hole. The surface of the water tank is open to the atmosphere, and the hole drains to the atmosphere. If you neglect the effect of the kinetic energy correction factor, calculate: a) the initial flow rate of the tank and b) the time it takes to empty the tank.c) Does the orifice loss coefficient cause a significant increase in tank drain time? yes or no, the emptying time for this case is t =

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS