The length of one side of a cube-shaped freezer cabinet is 11.8 m. your closet its base is perfectly insulated against heat transfer and the inner surface temperature is –5 °C, the outer surface temperature and it is 59°C. To ensure that the thermal load of the cabinet is not less than 0.59 kW The thickness of the styrofoam foam insulation (k=0.03 W/mK) to be applied to the upper and side surfaces What should be less?

The length of one side of a cube-shaped freezer cabinet is 11.8 m. your closet its base is perfectly insulated against heat transfer and the inner surface temperature is –5 °C, the outer surface temperature and it is 59°C. To ensure that the thermal load of the cabinet is not less than 0.59 kW The thickness of the styrofoam foam insulation (k=0.03 W/mK) to be applied to the upper and side surfaces What should be less?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.16P: 3.16 A large, 2.54-cm.-thick copper plate is placed between two air streams. The heat transfer...

See similar textbooks

Similar questions

2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick, as shown in the figure. There are to be 100 fins per meter. The convection heat transfer coefficient, both for the wall and the fins, is estimated to be K. With this information determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.
1.1 On a cold winter day, the outer surface of a 0.2-m-thick concrete wall of a warehouse is exposed to temperature of –5°C, while the inner surface is kept at 20°C. The thermal conductivity of the concrete is 1.2 W/m K. Determine the heat loss through the wall, which is 10-m long and 3-m high. Problem 1.1
The air-conditioning system in a Chevrolet van for use in desert climates is to be sized. The system is to maintain an interior temperature of 20C when the van travels at 100 km/h through dry air at 30C at night. If the top of the van is idealized as a flat plate 6 m long and 2 m wide and the sides as flat plates 3 m tall and 6 m long, estimate the rate at which heat must be removed from the interior to maintain the specified
3.16 A large, 2.54-cm.-thick copper plate is placed between two air streams. The heat transfer coefficient on one side is and on the other side is . If the temperature of both streams is suddenly changed from 38°C to 93°C, determine how long it takes for the copper plate to reach a temperature of 82°C.
Question 1:A glass window of width W = 1 m and height H = 2 m is 5 mm thick and has a thermal conductivity of kg=1.4 W/m.K. If the inner and outer surface temperatures of the glass are 15oC and -20oC, respectively, ona cold winter day, what is the rate of heat loss throughthe glass? To reduce heat loss through windows, it iscustomary to use a double pane construction in whichadjoining panes are separated by an air space. If thespacing is 10 mm and the glass surfaces in contact withthe air have temperatures of (last two digit of your Registration number) oC and -15oC, what isthe rate of heat loss from a 1 m x 2 m window? Thethermal conductivity of air is ka=0.024 W/m.K.
1. (a) Consider a room with a 1.8-m-high and 2.0-m-wide double-pane window consisting of two 4-mm-thick layers of glass separated by a 10-mm-wide stagnant air space. The convection heat transfer coefficients on the inner and outer surfaces of the window are 12 W/m2 K and 25 W/m2 K, respectively, while the average thermal conductivity of glass is 0.78 W/m K; and the air, 0.026 W/m K. If the room is maintained at 22 oC, the outside temperature is -4 oC and heat transfer due to radiation can be neglected, determine: (i) Draw the sketch and thermal resistance network; (ii) the total thermal resistance; (iii) the steady rate of heat transfer through this double-pane window; (iv) the temperature of the inner surface of the window.…
In a new residential project, you strongly believethat double-paned windows are ‘better’ than singlepaned windows. Compare the rate of heat loss betweensingle and double-paned windows (1.5 m x 1 m) if thethickness of each pane is (th = 0.4 cm) and (k = 0.9W/m.K). The indoor and outdoor temperatures are 18°C and 2 °C, respectively. Thickness of the air gapbetween the double-paned windows is (th = 1 cm), and(k = 0.022 W/m.K). Image credit: Windowwhirl
A long stainless-steel (AISI 316) steam pipe, with an inside diameter of 6.00 cm and an outside diameter of 8.00 cm, is covered with a layer of asbestos insulation (k = 0.150 W/m-K) 1.00 cm thick, which in turn is covered with foam insulation (k = 0.044 W/m-K) 6.00 cm thick. The inside surface temperature of the stainless-steel steam pipe is measured to be 250.0°C, while the outside surface of the foam is exposed to convection, T_inf = 25.0°C, h_inf = 15.0 W/m^2-K. • Draw and label a sketch of this system. Include dimensions, known temperatures, etc. • Draw and completely label the corresponding 1-D steady-state conduction resistor diagram. • Determine the heat transfer rate through the pipe per unit length. • Calculate the temperature at the asbestos/foam interface.
/ Hot square plate (1 m ×1 m) is to be cooled by attaching aluminum circular pin fins (D=0.25 cm, L= 3 cm) distributed with distance 0.6 cm as illustrated in Figs.(1-a) & (1-b). If the fin base temperature is 100°C, cooling air temperature is 30°C and h= 35 W/m. °C. Determine the total rate of heat transfer from the finned plate and the effectiveness of the fins? Assume k= 237 W/m.°C and nr=tanh mL/ mL.
In a new residential project, you strongly believe that double-paned windows are ‘better’ than single-paned windows. Compare the rate of heat loss between single and double-paned windows(1.5 m x 1 m) if the thickness of each pane is (th = 0.4 cm) and (k = 0.9 W/m.K). The indoor and outdoor temperatures are 18 °C and 2 °C, respectively. Thickness of the air gap between the double-paned windows is (th = 1 cm), and (k = 0.022 W/m.K). Image credit: Windowwhirl.
In a new residential project, you strongly believe that double-paned windows are ‘better’ than single-paned windows. Compare the rate of heat loss between single and double-paned windows (1.5 m x 1 m) if the thickness of each pane is (th = 0.4 cm) and (k = 0.9 W/m.K). The indoor and outdoor temperatures are 18 °C and 2 °C, respectively. Thickness of the air gap between the double-paned windows is (th = 1 cm), and (k = 0.022 W/m.K).
An electric resistance space heater is designed such that it resembles a rectangular box 50 cm high, 80 cm long, and 15 cm wide filled with 45 kg of oil. The heater is to be placed against a wall, and thus heat transfer from its back surface is negligible. The surface temperature of the heater is not to exceed 75°C in a room at 25°C for safety considerations. Disregarding heat transfer from the bottom and top surfaces of the heater in anticipation that the top surface will be used as a shelf, determine the power rating of the heater in W. Take the emissivity of the outer surface of the heater to be 0.8 and the average temperature of the ceiling and wall surfaces to be the same as the room air temperature. Also, determine how long it will take for the heater to reach steady operation when it is first turned on (i.e., for the oil temperature to rise from 25°C to 75°C). State your assumptions in the calculations.