The oil is pumped from a reservoir tank to the automobile tank. The volume flow rate of oil is 3,2 cm/s. The pipe diameter is 5 mm. The oil discharges through a 0.8-mm nozzle in a tank. The pressure in the tank is 95 kPa. The total head loss in the system is 1.1 m. If the pump has an efficiency of 58,18%, determine the power [W] needed by the pump. (NOTE: Po = 673 kg/m)

The oil is pumped from a reservoir tank to the automobile tank. The volume flow rate of oil is 3,2 cm/s. The pipe diameter is 5 mm. The oil discharges through a 0.8-mm nozzle in a tank. The pressure in the tank is 95 kPa. The total head loss in the system is 1.1 m. If the pump has an efficiency of 58,18%, determine the power [W] needed by the pump. (NOTE: Po = 673 kg/m)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please solve it correctly,Urgent. Question: The discharge pressure of a water pump is 9, 000 kPa. The temperature is 150 deg deg C and density is 917 kg/m3. What is the equivalent pump head in meters? A. 11.005 m B. 1,000.5 m C. 1,050.5m D. 1, 100.5 m
A pump is installed to deliver water from a reservoir of surface elevation zero, to another of elevation 290 ft. The 10 inch-diameter suction pipe (f=0.022) is 90 ft long and the 8-in-diameer discharge pipe (f=0.028) is 4900 ft long. The pump characteristic is defined by hp= 365-20Q2 where hp, the pump head, is in feet and Q is in cubic feet per second. What is the rate at which the pump will deliver the water?
5. The total head of a fan is 185 m and has a static efficiency pressure of 210 mm of water gage.What is the velocity of air flowing if the density of air is 1.15 kg per cubic meter? 8. A coal fired steam boiler uses 3000 kg of coal per hour. Air required for combustion is 15.5 kg ofcoal at barometric pressure of 98.2 KPa. The flue gas has temperature of 285 degree Celsiusand an average molecular weight of 30. Assuming an ash loss of 11% and allowable gas velocityof 7.5 meters per second. Find the diameter of the chimney 9. The gas density is 0.75 kg per cubic meters and air density is of 1.15 kg per cubic meter. If thedriving pressure is 0.25 KPA. Determine the height of the chimney. 10. A powerplant situated at an altitude having an ambient air of 96.53 KPa and 23.88 degreeCelsius. Flue gases at a rate of 5.0 kg per second enter the stack at 200 degree Celsius andleaves at 160 degree Celsius. The flue gases gravimetric analysis are 18% CO2, 7% O2 and 75%N2. Calculate the height of…
Nitrogen gas under a pressure pn = 15 psig is used for pumping kerosene at 25°C (density = 816 kg/m3, viscosity = 1.81 cP) through an elevation increase of 6 m. If there is an effective length of 45 m of nominal 2-in. schedule No. 40 pipe (commercial steel) between the two tanks, what is the flow rate of kerosene? Neglect exit kinetic-energy effects.
1. Assume a horizontal shaft handling water at 65 deg C (Pv=2.503 KPa, Density=980.5 m3/kg). The suction nozzle is 4.35 m below the pump centerline and the pressure gauge reading at this point is 221Kpag. Determine the NPSHa if the head loss is 0.82 m. If the NPSHr is 3m less than the NPSHa you got on question number 1, determine the pump suction specific speed at pump rotating at 1800rpm and Q=500gpm
Suppose that you are willing to determine the diameter of the water jet impinging to the sink from the kitchen tap.The tap is produced to supply three different flow rates of the low, medium, and high. For each flow rate level, waterthat comes from the tap fills the beaker with a volume of 30 mL in 10 s, 6 s, and 2 s, respectively. The outlet of the tapis 13 mm, and the distance between the tap outlet and the sink is 53 mm. Determine the diameters of the water jetimpinging on the sink at three given flow rates.
Flow turbulence and cavitation in a centrifugal pump generate a similar sound to the human ear. Explain how vibration analysis would help you to determine which is which.
Find the pressure head at entry of the pipe, when the pressure of flowing fluid is 275 N/cm? The pressure head at entry (Unit in Pascal)?
Chlorine gas is moving through a pipeline at a rate of 200 kilogram per hour while being pressured at 5 psig and operating at 800 F. If the pipe has a diameter of 5 inches, what is the flow velocity, expressed in meters/second?
A pump delivering 0.23 m3/s of water has a 304.8mm diameter suction flange and 254mm discharge flange. The suction pipe is 3.66m long and the discharge pipe is 22.86m long. Neglecting the turbulence losses in the pipe, find: a.) the head which the pump must deliver ( in meters ) b.) the motor power in KW required if the efficiency is 80%, c.) the reynold’s number and type of flow in the suction pipe d.) the reynold’s number and type of flow in the discharge pipe
Air velocity in a duct is measured as 38.2 m/s by a pitot tube. Density of flowing air 1.3 kg/m3. If the pressure difference recorded by the pitot static tube is 0.1 m of water, calculate the coefficient of velocity of the pitot static tube. A Figure or Free Body Diagram will be much appreciated. Thank you
For the flow configuration shown, you are required to design a pump station to transfer water from the bottom tank to the upper tank. In your own words, explain the steps that are needed to be followed for the design of the pump system. Your answer should be typed and not more than one page. The pipe equivalent roughness is 1.5 mm. And a valve with a k=10 is located just upstream of the lower reservoir (other losses are negligible). Take p=1000 kg/m”, g = 9.81 m/s?, and u = 1.179 x 102 kg/m.s.