a speed booster. The input shaft rotates at 500 rpm and has a sheave iameter of 7.218 in and the output shaft has a sheave with a pitch diameter 9 in. The center distance between the two shafts is 15.01 in. The coefficient ion is 0.25 and the maximum tension in the tight side of the belt is 300 lb. ine3; e angular velocity of the output shaft. e belt wrap on the input and output sheaves. e belt perimeter length. e length of span between sheaves. e maximum power transmitted by the belt if its mass is 0.04 slug/ft. [Hint: (T-T2)xv P in horse power (hp), T, and T2 in (lb). v in (ft/min)]. 33000

a speed booster. The input shaft rotates at 500 rpm and has a sheave iameter of 7.218 in and the output shaft has a sheave with a pitch diameter 9 in. The center distance between the two shafts is 15.01 in. The coefficient ion is 0.25 and the maximum tension in the tight side of the belt is 300 lb. ine3; e angular velocity of the output shaft. e belt wrap on the input and output sheaves. e belt perimeter length. e length of span between sheaves. e maximum power transmitted by the belt if its mass is 0.04 slug/ft. [Hint: (T-T2)xv P in horse power (hp), T, and T2 in (lb). v in (ft/min)]. 33000

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.70P: Solve Sample Problem 7.16 if the contact pressure under the polisher varies parabolically from p0 at...

See similar textbooks

Similar questions

The roughly position of the automobile jack shown in the figure is a square screw with a single blade at both ends. ABC is controlled by a bolt (right-hand threaded in A, left-handed in C). square of the bolt screw has a pitch of 2.5 mm and an average diameter of 9 mm. between the bolt and the jack limbs The coefficient of static friction is 0.15, taking into account the position and load shown, you can use the jack Find the magnitude of the torque that must be applied to raise it.
The following figure shows a belt brake system operating on a brake drum of the hoisting mechanism. It consists of a cylinder with a diameter of 325 mm, the end of which is the elastic belt connected to both ends of the elastic belt by a crank arm articulated at B and the angle of rotation = 225 degrees. And the coefficient of friction is 0.3 and the latching force is f. Find the necessary F to generate a torque of 350 on the cylinder while it is rotating in the direction shown? Note that s = c = 135mm a = 500mm. 35mm
PROBLEM The diameter of two pulleys are (0.3m)and (0.2m), center distance (1m).if we use open belt drive. Determine: 1- the length of V-belt (2ß = 60°). 2- the contact angle between belt and smaller pulley. 3- the horse power, if the smaller pulley turn with speed (400r.p.m) and the tension force in tight side (T1=900N), coefficient of friction ų=0.3 4- the speed of large pulley.
Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? give proper explaination and dont give handwritten solution.
6. Design a clamp coupling for transmitting 36 kW, at 200 rpm. Allowable shear stress in shaft is 45 MPa, allowable shear stress in key is 40 MPa, and allowable crushing stress in key is 90 MPa. The number of bolts joining the two halves is 4. The permissible tensile stress in bolts is 60 MPa. The coefficient of friction between the muff and shaft can be taken as 0.25
The block type handbrake shown in the figure has a width of 49 mm and an average friction coefficient of 0.32. Calculate the maximum pressure and braking moment on the lug to ensure the expectation of a thrust force of 483 N in the system with the reverse direction of the clock hand.
A pulley system uses four v-section belts each with a cross-sectional area of 700mm 2, an included angle of 40°, and density 1400kg/m 3 The angle of lap is 130° on the smaller wheel, the coefficient of friction is 0.4 and the maximum force allowed in the belt is 500N. Calculate the initial belt tension and reason for this.
Problem: A pump is driven by an electric motor through an open type flat belt drive. Determine the belt specificationsfor the following data.Motor pulley diameter= 400 mmPump pulley diameter = 800 mmCoefficient of friction for motor pulley = 0.30Coefficient of friction for pump pulley = 0.35Center distance between the pulleys=2000 mmRotational speed of the motor=2000 rpmPower transmission = 40kWdensity of belt material = 1000 kg/m3 width of the belt=240mmthickness of the belt = 5mm
8. Design a clamp coupling for transmitting 25 kW at 300 rpm. Allowable shear stresses in shaft and key are 50 MPa and 45 MPa, respectively. The number of bolts joining the two halves of muff is 4. The permissible tensile stress in the bolt is 70 MPa and the permissible crushing stress in the key is 90 MPa. The coeffi cient of friction between the muff of the CI and the shaft of steel is 0.20.
Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? dont write handwritten solution.
For the drum brake shown in the following figure, there is an inner rim diameter of 280 mm and dimension a = 90 mm. The shoes have a face width of 30 mm. The force exerted by the cylinder hydraulic is 1000 N and the average coefficient of friction is 0.3. Determine: a) The maximum pressure in each shoe; b) The braking torque; c) Reactions resulting from the pivot pin;
A cone clutch has cone elements at an angle of 12o. The clutch transmit 25 HP at a speed of 1200 rpm. The mean diameter of the conical friction section is 16 in and the coefficient of friction is 0.35. Find the axial force needed to engage the clutch.