Q3) (8plates that are welded at the seams in the orientation shown. The tank has an inside diameter of400 mm and a wall thickness of 5 mm. If the gage pressure is 4 MPa, using Mohr's circle,determine the normal stress perpendicular to the weld and shear stress parallel to the weld.The pressure tank shown in Figure is fabricated from spirally wrapped metal50°

Given P=4MPa d=400mm t=5mm angle Q=50o C

The pressure tank shown in Figure is fabricated from spirally wrapped me plates that are welded at the seams in the orientation shown. The tank has an inside diameter 400 mm and a wall thickness of 5 mm. If the gage pressure is 4 MPa, using Mohr's cir determine the normal stress perpendicular to the weld and shear stress parallel to the weld.

The pressure tank shown in Figure is fabricated from spirally wrapped me plates that are welded at the seams in the orientation shown. The tank has an inside diameter 400 mm and a wall thickness of 5 mm. If the gage pressure is 4 MPa, using Mohr's cir determine the normal stress perpendicular to the weld and shear stress parallel to the weld.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The pressure tank shown is fabricated from spirally wrapped metal plates that are welded at the seams in the orientation shown where β=55∘β=55∘. The tank has an inside diameter of 26.626.6 in.in. and a wall thickness of 0.3500.350 in.in. Determine the largest gage pressure that can be used inside the tank if the allowable normal stress perpendicular to the weld is 18.518.5 ksiksi and the allowable shear stress parallel to the weld is 8.58.5 ksiksi.
The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 48 in. and a wall thickness of 0.375 in. Determine the largest allowable gage pressure if the allowable shear stress parallel to the weld is 3.10 ksi.
The point on the surface of the pressure vessel in Fig.a is subjected to the state of plane stress. Determine the absolute maximum shear stress at this point.
A cylindrical pressure tank is fabricated by butt-welding 19 mm-thick plate with spiral seam shown below. The pressure in the tank is 2.76 MPa, and an axial load of 133.5 KN is applied to the end of the tank through a rigid bearing plate. Determine the normal stress and shearing stress perpendicular to the weld.
For the pin connection shown, determine the normal stress acting on the gross area, the normal stress acting on the net area, the shear stress in the pin, and the bearing stress in the steel plate at the pin.
A typical stainless steel cylindrical vessel is shown. The inside diameter of the tank is 48.0 in. and the wall thickness is 0.75 in. The tank is pressurized to 1.10 ksi. Determine the hoop stress in the wall of the tank.
What will be the maximum weight of cylinder that can be put as shown in the figure below if the maximum stress at cable is 104 mPa. Round of your answer in two decimal places.
A cylindrical propane tank has an outside diameter of 3.25 m. If the allowable hoop stress is 100 MPa and the allowable axial or longitudinal stress is 45 MPa, determine the minimum thickness of the pipe when the internal pressure that can be applied to the tank is 1.25 MPa.
The pressure tank shown has an 8-mm wall thickness and butt-welded seams forming an angle β=20° with a transverse plane. For a gage pressure of 600 kPa, determine (a) the normal stress perpendicular to the weld, (b) the shearing stress parallel to the wel
A steel pipe 1.5m in diameter is required to carry an internal pressure of 750 KPa. If the allowable tensile stress of steel is 140 MPa, determine the required thickness of the pipe in mm.
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The diameter of the pressure vessel is 450 mm, and its length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa, and the circumferential stress is limited to 60 MPa.
A steel pipe 1.5m in diameter is required to carry an internal pressure of 650kPa. If the allowable tensile stress of steel is 140 MPa, determine the required thickness of the pipe in mm.