The single-line diagram of a subtransmision system is presented in the figure below. At point B a three- phase short circuit has occurred. Calculate the voltage at points A, B, C and D. Three phase short circu Infinite bus D C +j0.2 j0.67 +j1.05 +j0.70

The single-line diagram of a subtransmision system is presented in the figure below. At point B a three- phase short circuit has occurred. Calculate the voltage at points A, B, C and D. Three phase short circu Infinite bus D C +j0.2 j0.67 +j1.05 +j0.70

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.32MCQ: While the instantaneous electric power delivered by a single-phase generator under balanced...

See similar textbooks

Related questions

Q: 1. How do you measure three phase line currents by using two current transformers? Draw the…

A: The diagram for the three-phase system and the two current transformers are drawn below, Consider…

Q: Three single-phase two-winding transformers, each rated 400 MVA, 13.8/ 199.2 kV, with leakage…

Q: (a) A single phase, unity power factor load takes 70 A at 25 kV. Using a base voltage of 60 kV and…

A: Per unit

Q: With neat diagrams explain how a three phase delta connection to be made with three windings and…

A: Resistors, inductors and capacitors form an integral part of any electrical circuit. A source,…

Q: For the power system shown at right the impedance matrix (2 is j0.4 3 j0.5 j0.2 0.164 0.101 0.0692…

Q: A three-phase fault with a fault impedance Zf = j0.16 per unit occurs at bus 3 in the Figure beside,…

A: The answer is 2. Please fill answer only 2.

Q: Determine the ripple factor and the average load current of the given circuit shown. Finalize answer…

Q: L-type equivalent circuit and parameters for a continuous sinusoidal phase of a 5.5 kW, 1450 rpm,…

A: According to the question we have to calculate how many times the inrush current will be the rated…

Q: 6. A 3 phase fault occurs at point F as shown in figure. Determine the critical clearing angle for…

A: Given figure, 3 phase fault occurs at point F as shown in the figure. The generator is delivering…

Q: Problem-4: Solve at Home Problem-4, Cont... The one-line diagram of a simple three-bus power system…

Q: Generators generate positive sequence voltage only False True

A: Positive Sequence: The positive sequence is a three-phase balanced system in which the system has…

Q: The sequence component line currents of a three-phase, 4-wire system are the following: Ia0 =…

Q: Three-phase alternator supplying a three wires, CBA system with a line voltage of 100 Volt,…

Q: Calculate the initial symmetrical short circuit current that will occur when a 3 phase short circuit…

A: We can re draw the given system as Let the base MVA of the system i.e SB 500MVA and base Voltage…

Q: Discuss the phase shift method of generating SSB through this block diagram

A: The block diagram is shown below,

Q: Three zones of a single-phase circuit are identified in the figure with a generator voltage…

A: For the evaluation of electrical machines, one-of-a-kind values are required, consequently, per unit…

Q: Obtain the per-unit equivalent circuit for the following one-line diagram in Figure 1. Xine = 100 Q…

Q: The one-line diagram of a simple power system is shown in Figure 9.20. Each generator is represented…

Q: The one line diagram of power system is shown in Figure Q.1. Use a common base MVA of 100 MVA and…

Q: The total instantaneous power absorbed by a three-phase motor (under balanced steady-state…

A: Consider the instantaneous voltage across phase a and the neutral terminal is given by:

Q: (b) A 50 Hz synchronous generator with inertia constant H = 6.2 MJ/MVA is connected to an infinite…

Q: L-type equivalent circuit and parameters for a continuous sinusoidal phase of a 5.5 kW, 1450 rpm,…

A: According to the context of the given question, it is required to determine the number of times…

Q: The one-line diagram of a simple power system is shown in Figure below. The neutral of each…

A: In this question we need to find a 3 phase fault at bus 3 .

Q: The one-line diagram of a simple three- bus power system is shown below. Each generator is…

A: In this question we need to find a 3phase fault across bus 1 .

Q: Figure below shows a power system where load at bus 5 is fed by generators at bus 1 and bus 4. The…

A: When line L1 has length =100 km, fault current for fault at bus 5 is =2530 A When line L1 reduced to…

Q: 2-What is the relationship between phase and line quantities in balanced star and delta connections?…

A: As per Bartleby guidelines we are allowed to solve only one question, please ask the rest again.…

Q: What can you say about the flow of power as a function of time between a balanced three-phase source…

A: Concept: A definition of a function is that a relation from a set of inputs to a set of possible…

Q: What load can be delivered by a 3-phase overhead line 5 km long with a pressure drop of 10%. Given…

Q: Discuss with block diagram, the principle of operation of single phase energy met

A: (i provide you the solution in RULE PAPER for easily understand to the diagram and its related…

Q: ork why we need to consider the neutral impedance 3 times

A: The zero sequence components are in having the same phase in all the three phases. When there is a…

Q: In a three phase overhead system , each line is suspended by a string of three insulators. The…

A: Given V1=8 kV V2=11 kV m=CshCsat V2=V1(1+m)(1+m)=V2V1=118=1.3751+m=1.375m=1.375-1…

Q: Figure below shows a power system where load at bus 5 is fed by generators at bus 1 and bus 4. The…

A: 1) When base voltage is changed to 11 kV, change in fault current ? 2)

Q: Differentiate Wye and Delta Connection in Three Phase System and Relate it with Computer Engineering

A: The differences between the wye and delta connection is listed in the table shown below: Delta…

Q: capacitors will supply reactive VAR during peak load condition and consumes reactive VARs during…

A: 1.Booster Transformer:-It is used at the end of a power line or at the intermediate position to…

Q: A three-phase symmetrical double circuit line is arranged in a horizontal plane as shown in figure…

A: Transposed line: It is an arrangement of conductors. In this conductors are periodic changes its…

Q: Sketch the complete per-phase equivalent circuit of a symmetrical non-salient pole three-phase…

A: Synchronous generator: It is an electromechanical device. This is called a synchronous generator…

Q: The zero sequence currents of a generator for line to ground fault is j2.4 p.u. then the current…

Q: (b) A 50 Hz synchronous generator with inertia constant H = 6.2 MJ/MVA is connected to an infinite…

Q: The sequence component line-to-line voltages of a three-phase, 4-wire system are the following: Vab0…

Q: 7. Which of the following are sometimes installed as an emergency system, legally required standby…

A: In this question, Choose the correct option Which of the following are sometimes installed as an…

Q: Single Phase equivalent Y-Y system is shown in the figure 3 below, operated by a generator with…

A: Single phase equivalent circuit as given in the circuit is shown below

Q: UDng a ITIe Core in high frequency transformers. c- Discuss, different applications of iron cores of…

A: C)For magnetizing or demagnetizing a iron material, some energy is expended. The energy expended…

Q: For the power system shown at right the impedance matrix 2 is j0.5 j0.2 3 j0.4 0.145 0.120 0.0692…

A: New voltage at a bus = old bus voltage + change in voltage

Q: Calculate the inductance per phase per meter for a three- phase double-circuit line whose phase…

A: In this question, Find the inductance of the 3 phase double circuit as per given Horizontal…

Q: Is it true??

A: For the transmission of the equal power to three loads impedance will need only the half of the…

Q: e = 0 Q1: What does happen if we change two currents? Q2: What does happen if we have a three-phase…

A: 1)It is not possible that , current can flow in two directions at same time. However if we apply two…

Q: The terminal voltage of a 3-φ generator is 19053 V, line-to-line. The load draws a current of 1515…

Concept explainers

Fault Analysis

In an electrical engineering system, a fault is an abnormal electric current flowing through the system, and fault analysis is the study of these faults. For instance, a short-circuit is a fault where the live wire touches the ground or neutral wire. If a circuit is interrupted by a failure of a current-carrying wire then an open circuit fault occurs. The open-circuit faults are also called series faults. One or more phases or ground may be involved in a three-phase fault or may occur only between two phases. Current flows into the earth in case of a ground fault or earth fault. For most situations, the prospective short circuit current of a fault that is predictable can be calculated. To limit the loss of service because of a failure, the protective devices can detect fault conditions and operate circuit breakers and also other devices. All phases equally can be affected in a poly-phase system which is known as symmetric electrical fault. The asymmetric fault becomes more complicated to analyze if only some phases are affected. By using methods such as symmetrical components, the power system analysis of these types of faults is often simplified. The main objective of power system protection is to design, detect, and interrupt power system faults.

Question

The single-line diagram of a
subtransmision system is presented in
the figure below. At point B a three-
phase short circuit has occurred.
Calculate the voltage at points A, B, C
and D.
Three phase short circuit
Infinite bus
D
+j0.2
j0.67
+10.70
+j1.05
V-1.00 pu

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The annual load duration curve of a power supply system may be considered as straight line from 40 MW to 8 MW. The load factor of the system is ?
Which termination would result to a phase change of 180 degrees at the load if Zo = 100 ohm? a. 50 ohm b. short circuit c. 75 ohm d. all of these What is the purpose of impedance matching? a. maximum return loss b. maximum SWR c. maximum load power d. maximum reflection A short piece of transmission line that may be open or shorted and used for impedance matching purposes. a. converter b. decoder c. stub d. transformer
L-type equivalent circuit and parameters for a continuous sinusoidal phase of a 5.5 kW, 1460 rpm, line voltage 220 V and frequency 50 Hz star-connected 3-phase ASM, ignoring core (iron) losses given as follows: R1=0.21 Ohm, R2=0.18 Ohm, X1=X2=0.66 Ohm and Xm=9.9 Ohm How many times the inrush current will be the rated current when the ASM is started directly? Answer options group 3.7473 5.2280 8.0815 7.1534 1.2558 4.3763 2.6455 6.3414
3. Which one of the following method uses weak coupling between reactive power and voltage angle?. A. Newton - Raphson Method B. Decoupled Method C. Gauss-Seidal Method
L-type equivalent circuit and parameters for a continuous sinusoidal phase of a 5.5 kW, 1450 rpm, line voltage 220 V and frequency 50 Hz star-connected 3-phase ASM, ignoring core (iron) losses given as follows: R1=0.21 Ohm, R2=0.18 Ohm, X1=X2=0.66 Ohm and Xm=9.9 Ohm How many times the inrush current will be the rated current when the ASM is started directly?
5.5 kW, 1450 rpm. L-type equivalent circuit and parameters for a continuous sinusoidal phase of a star connected 3-phase ASM with line voltage 220 V and frequency 50 Hz are given as follows, ignoring core (iron) losses: R1=0.21 Ohm, R2=-0.18 Ohm, X1=X2-0.66 Ohm and Xm = 9.9 Ohm How many times the inrush current will be the rated current when the ASM is started directly? Answer options group 8.0815 2.6455 4.3763 7.1534 1.2558 6.3414 5.2280 3.7473
L-type equivalent circuit and parameters for a continuous sinusoidal phase of a 5.5 kW, 1450 rpm, line voltage 220 V and frequency 50 Hz star-connected 3-phase ASM, ignoring core (iron) losses given as follows: R1=0.21 Ohm, R2=0.18 Ohm, X1=X2=0.66 Ohm and Xm=9.9 Ohm How many times the rated current will the inrush current be when the ASM is started directly?
• Zh = 100 ohm • Draw the pu reactance diagram by taking Ut(base) = 132kV, St(base) = 100MVA. If the 33 kV busbar voltage is kept constant at 30 kV and 0.8 inductive 50 MVA power is drawn from this bus, what is the voltage at the synchronous machine ends?
For the power system with a single line diagram;Draw the reactance diagrams of the zero, positive and negative component circuits of the system by selecting the base values of 1000 MVA and 20 kV in the generator G3 region. (?0=?1=?2=50 ?ℎ? for each line)
Two overhead lines AB (Z0 = 500 Ω, length = 300 km, attenuation factor = 0.8) and BC (Z0= 300 Ω, length = 120 km, attenuation factor = 0.9) feed a load of surge impedance 1700Ω at C. A triangular wave of peak height (875)/2 kV and duration 300 µs originates in theoverhead line AB at A and travels towards B. Using Bewley Lattice Diagram, determineand sketch the voltages at A, B and C for the first 2 ms. A to J z0=500 ohm, C to J z0 = 300 ohm B to J z0 = 400 ohm D to J z0 = 50 ohm.
A three phase symmetrical double circuit line is arranged in a horizontal plane as shown in figure below. Calculate and derive an expression for the transposed line for the inductance. Assume balanced equally distributed loads.
A balanced, star connected three-phase system is directly connected to an unbalanced load, with a solid neutral connection. The line-to-neutral voltage Van on the load side and per phase load impedances (i.e., Za, Zb and Zc) are as below: ?an = 240∠0 ? ?? = 10 + 3? Ω ?? = 16 + 3? Ω ?? = 10 + 3?Ω Draw the circuit diagram and calculate the sequence currents and neutral current