Answered: The zero sequence currents of a…

The zero sequence currents of a generator for line to ground fault is j2.4 p.u. then the current through the neutral during the fault is j0.8 True False

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16MCQ: With generator conyention, where the current leaves the positive terminal of the circuit element, if...

See similar textbooks

Related questions

Q: In the following 3-phase power system, the voltage at point a is initially 0.95 pu, and the motor is…

A: In this question we need to find a fault current of the given system when a ground fault occurs at…

Q: 1. How do you measure three phase line currents by using two current transformers? Draw the…

A: The diagram for the three-phase system and the two current transformers are drawn below, Consider…

Q: What is load line and what is duty cycle?

Q: Which among the following faults does mostly happen in 3-phase power systems? Single line to ground…

A: As 3 phase fault in power system are, 1. Single Line to Ground fault 2. Three phase short circuit 3.…

Q: Write an introduction about: LOAD BALANCING in 3-Phase System

A: Three-Phase System - A three-phase system is formed out of a three-phase voltage source that is…

Q: For the power system shown at right the impedance matrix (2 is j0.4 3 j0.5 j0.2 0.164 0.101 0.0692…

Q: In a three phase overhead system, each line is suspended by a string of three insulator. The voltage…

Q: In the figure below, all impedances are in per unit on a common MVA base. The generators are…

Q: Determine the ripple factor and the average load current of the given circuit shown. Finalize answer…

Q: pecified in per unit. For generators, assume Z* =Z` =j0.2, Z° = j0.05 For transformers, assume Z' =…

Q: A three-phase, wye-connected, 7 kVA, 230 V synchronous generator has a reactance of 7 ohms per…

A: Base impedance=Voltagecurrent =Voltagecurrent×voltageVoltage…

Q: Under Unbalanced Condition With Faults: a. Load Line Currents (la, Ip,!c); b. Load Line Voltages…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: Problem-4: Solve at Home Problem-4, Cont... The one-line diagram of a simple three-bus power system…

Q: Generators generate positive sequence voltage only False True

A: Positive Sequence: The positive sequence is a three-phase balanced system in which the system has…

Q: The value of value of voltage measured in residential convenience outlet is average voltage. True…

A: Average value is the average of the signal over the period of time. Where as rms value of the signal…

Q: Three single-phase two-winding transformers,

Q: In a power system the fault is occurred in all the lines and to the ground without fault impedance…

A: all the line and to the ground fault is symmetrical fault.

Q: Obtain the per-unit equivalent circuit for the following one-line diagram in Figure 1. Xine = 100 Q…

Q: Hourly variation factor need to consider while dealing with the non-coincidence demand of different…

A: A power station is to provide electricity to a huge number of people. Different customers' power…

Q: 2- The Purpose of using Unbalanced Three-phase Systems: Ji

A: Need to find purpose of using unbalanced three phase system

Q: in a tie-bus arrangement as shown in figure. the reactances of the generators and reactors are 0.2…

A: We redraw the circuit on per phase per unit basis: In the circuit the fault point is connected to…

Q: The one-line diagram of a simple three- bus power system is shown below. Each generator is…

A: In this question we need to find a 3phase fault across bus 1 .

Q: Figure below shows a power system where load at bus 5 is fed by generators at bus 1 and bus 4. The…

A: When line L1 has length =100 km, fault current for fault at bus 5 is =2530 A When line L1 reduced to…

Q: 3. A 100 MVĂ, 33KV 3-phase alternåtör current are as under: 3-phase fault-2000A, Line to Line…

A: Please refer the attached images for the complete answer..

Q: The one-line diagram of a power system is shown in the figure below. A single-line-to- ground (SLG)…

A: A single line to ground fault occurs at bus 2. So the fault current will be- Ea=Genetaror terminal…

Q: Discuss with block diagram, the principle of operation of single phase energy met

A: (i provide you the solution in RULE PAPER for easily understand to the diagram and its related…

Q: 2) For a given short-circuit calculation utilizing the per unit method, a base voltage of 480 V and…

A: Given, Base voltage, Vb=480 V Base power, Sb=2500 kVA

Q: Discuss FOUR (4) advantages of per-unit system.

Q: A three-phase fault with a fault impedance Zf = j0.16 per unit occurs at bus 3 in the Figure beside,…

A: We use z bus matrix to find fault.

Q: 2- The Purpose of using Unbalanced Three-phase Systems: Jji

A: Actually we are not intentionally use the unbalanced system. Unbalanced system created due to the…

Q: Figure below shows a power system where load at bus 5 is fed by generators at bus 1 and bus 4. The…

A: 1) When base voltage is changed to 11 kV, change in fault current ? 2)

Q: Find an admittance matrix for the following four-lane system. Each track is a ﬁ model with a series…

Q: What is the negative sequence component

Q: Q1. A// Choose the correct answer: 1. One of the advantage of using a per unit system in power…

A: According to guidelines we are allowed to do only first 3 questions , please post again for…

Q: 3) The single-line diagram of a three-phase system is given in Figure 3. The three-phase generator…

A: Since you have asked multiple questions in a single request, we will be answering only the first…

Q: Q3: Derive the relationship between positive and negative sequence components when single phasing…

A: Single phasing Three phase supply is fed to a load e.g. induction motor When one of the phase is get…

Q: A three-phase synchronous generator produces 10 MVA power under a rated voltage of 10 kV. Zero…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: 2- The Purpose of using Unbalanced Three-phase Systems:

A: The purpose of using unbalanced three phase system is

Q: For the power system shown at right the impedance matrix 2 is j0.5 j0.2 3 j0.4 0.145 0.120 0.0692…

A: New voltage at a bus = old bus voltage + change in voltage

Q: All Choose the correct answer: 1. One of the advantage of using a per unit system in power system…

A: Per unit quantity is equal to the division of actual quantity and base quantity. There are two types…

Q: Q1. All Choose the correct answer: 1. One of the advantage of using a per unit system in power…

A: As per the guidelines of Bartley we supposed to answer first three subpart only.

Q: Draw the reactance diagram of the given one-line diagram below marked in appropriate per unit…

Q: A surge of 100 kV travels along an overhead line towards its junction with a cable. The surge…

A: we need to determine magnitude of surge transmitted through cable.

Q: Athree-phase, wye-connected, 6.25 kVA, 220 V synchronous generatorhas a reactance of 8.4 N perphase.…

A: The given system is a three-phase Y connected, the base values are as follows: Vbase=220…

Q: Example-1: In a single-loop distribution system shown in the figure consider the generator to be of…

A: A) Given fault is L-L fault:Ip=3×ER1X1eq+X2eqIp=3×1.0X1eq+X2eqAt…

Q: In the shown below power system, both generators G1 and G2 emf's are equal. All the system data are…

Q: a) The one line diagram of a three phase system is shown below, draw an impedance diagram showing…

A: It is given that:

Concept explainers

Three-Phase Transformers

Three-segment transformers are a type of transformer used to transform voltages of electrical systems into three ranges. Two type transformers are shell-type transformer and core type transformer. In brief, it could be described because of the exquisite kinds of configurations.

Transformer

Ever since electricity has been created, people have started using it in its entirety. We see many types of Transformers in the neighborhoods. Some are smaller in size and some are very large. They are used according to their requirements. Many of us have seen the electrical transformer but they do not know what work they are engaged in.

Question

The zero sequence currents of a generator for line to ground fault is j2.4 p.u. then the current through the neutral during the fault is j0.8
True
False

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

With generator conyention, where the current leaves the positive terminal of the circuit element, if P is positive then positive real power is delivered. (a) False (b) True
Three single-phase two-winding transformers, each rated 25MVA,34.5/13.8kV, are connected to form a three-phase bank. Balanced positive-suence voltages are applied to the high-voltage terminals, and a balanced, resistive Y load connected to the low-voltage terminals absorbs 75 MW at 13.8 kV. If one of the single-phase transformers is removed (resulting in an open connection) and the balanced load is simultaneously reduced to 43.3 MW (57.7 of the original value), determine (a) the load voltages Va,Vb, and Vc; (b) load currents Ia,Ib, and Ic; and (c) the MVA supplied by each of the remaining two transformers. Are balanced voltages still applied to the load? Is the open transformer overloaded?
Consider a single-phase electric system shown in Figure 3.33. Transformers are rated as follows: XY15MVA,13.8/138kV, leakage reactance 10 YZ15MVA,138/69kV, leakage reactance 8 With the base in circuit Y chosen as 15MVA,138kV determine the per-unit impedance of the 500 resistive load in circuit Z, referred to circuits Z, Y, and X. Neglecting magnetizing currents, transformer resistances, and line impedances, draw the impedance diagram in per unit.
Consider the single-Line diagram of a power system shown in Figure 3.42 with equipment ratings given: Generator G1: 50MVA,13.2kV,x=0.15p.u. Generator G2: 20MVA,13.8kV,x=0.15p.u. Three-phase -Y transformer T1: 80MVA,13.2/165YkV,X=0.1p.u. Three-phase Y- transformer T2: 40MVA,165Y/13.8kV,X=0.1p.u. Load: 40MVA,0.8PFlagging,operatingat150kV Choose a base of 100 MVA for the system and 132-kV base in the transmission-line circuit. Let the load be modeled as a parallel combination of resistance and inductance. Neglect transformer phase shifts. Draw a per-phase equivalent circuit of the system showing all impedances in per unit.
The rating of generator is expressed in terms of kVA Select one: True False
In a three phase overhead system, each line is suspended by a string of three insulator. The voltage across top unit and the middle unit are 7 kV and 10 kV respectively. Calculate, a) Line voltage. b) String efficiency
For the same voltage and current produced by a three phase and single phase source, the power produced by the three phase source will be three times that of the single phase source. True False
Each track is a ﬁ model with a series impedance and a sequence for track C as shown in the table with p.u. values and the table below is based on power base = 60 [MVA]. Find an admittance matrix for the following four-lane system if power base = 50[MVA]
In a 3-phase overhead system, each line is suspended by a string of 3 insulators. The voltage across the top unit (i.e. near the tower) and middle unit are 10 kV and 11 kV respectively. Calculate (i) the ratio of shunt capacitance to self capacitance of each insulator, (ii) the string efficiency and (iii) line voltage
In the shown below power system, both generators G1 and G2 emf’s are equal.All the system data are shown on the system diagram.a) Draw the system diagram in per unit using (MVA)base = 75 and (KV)base =20 KV in the generators side.b) Calculate the three-phase balanced short circuit current (If) at busbar 3 inAmpere and the fault level (MVA)sc in MVA.c) If the fault at busbar 3 is a line-to-line fault, calculate the fault current inAmpere and the fault level (MVA)sc in MVA.
A three phase generator with constant terminal voltages gives the following currents when under fault: 1400 A for a line-to-line fault and 2200 A for a line-to-ground fault. If the positive sequence generated voltage to neutral is 2 ohms, find the reactances of the negative and zero sequence currents.
In a 3-phase Overhead System, each line is suspended by a string of 3 Insulators. The voltage across the top unit and middle unit are 10KV and 11KV respectively. Calculate (i) Ratio of Shunt Capacitance to Self-Capacitance of each insulator and (ii) String Efficiency