The stress-strain diagram for a metal alloy is shown. If the diameter of testing sample is 0.5 in determine: a) UTS b) Yield Stress c) Braking/ Failure Stress d) Young Module of Elasticity e) The load causing yielding in material 10 σ (ksi) 70 60 40 30 20 0 50 0.02 0.04 0.002 0.004 0.06 0.08 0.006 0.008 0.10 0.010 e (in./in_

The stress-strain diagram for a metal alloy is shown. If the diameter of testing sample is 0.5 in determine: a) UTS b) Yield Stress c) Braking/ Failure Stress d) Young Module of Elasticity e) The load causing yielding in material 10 σ (ksi) 70 60 40 30 20 0 50 0.02 0.04 0.002 0.004 0.06 0.08 0.006 0.008 0.10 0.010 e (in./in_

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2. Given a set of data that measured a diameter of a tube d1 = 1.65 mm, d2 = 1.66 mm, d3 = 1.65 mm, d4 = 1.64 mm Determine the uncertainty of the diameter
The S-N curve which represents the fatigue strength, which is measured as a stress amplitude, as a function of number of stress cycles, can be approximated by a straight line in therange of 103cycles to 106cycles when plotted as log(S) versus log(N). Beyond 106cycles,the fatigue strength remains constant. The fatigue strength of a certain alloy at 103cyclesis given as 80 % of the ultimate tensile strength and its endurance limit is 50 % of theultimate tensile strength.(a) The alloy part fails in 15 000 cycles. Calculate the percent change (increase or decrease)of the maximum applied cyclic stress amplitude if the life of the part needs to beextended by 3.5 times. Is this considered under a high or low cycle fatigue failure?State any assumptions made. (12 marks)(b) If the applied cyclic stress amplitude remains unchanged when the life is extended by3.5 times, calculate the percent change (increase or decrease) of the ultimate tensilestrength of a new alloy required. (8 marks)(c) If the…
Choose the correct answer Stress divided by Rate of strain is: d. Velocity a. Surface tension f. Kinematic viscosity b. Density e. Dynamic Viscosity c. Unit less
In a tensile test on a specimen of black mild steel of 12 mm diameter, the following results were obtained for a gauge length of 60 mm. Load W(kN) 5 10 15 20 25 30 35 40 Extension x (10-3 mm) 14 27.2 41 54 67.6 81.2 96 112 When tested to destruction. Maximum load = 65 kN; load at fracture = 50 kN, diameter at fracture = 7.5 mm, total extension on gauge length = 17 mm. Find young's modulus, specific modulus, ultimate tensile stress, breaking stress, true stress at fracture, limit of proportionality, percentage elongation, percentage reduction in area. The relative density of the steel is 7.8. Draw the straight line graph.
In a tensile test on a specimen of black mild steel of 12 mm diameter, the following results were obtained for a gauge length of 60 mm. Load W(kN) 5 10 15 20 25 30 35 40 Extension x (10-3 mm) 14 27.2 41 54 67.6 81.2 96 112 When tested to destruction. Maximum load = 65 kN; load at fracture = 50 kN, diameter at fracture = 7.5 mm, total extension on gauge length = 17 mm. Find young's modulus, specific modulus, ultimate tensile stress, breaking stress, true stress at fracture, limit of proportionality, percentage elongation, percentage reduction in area. The relative density of the steel is 7.8. Draw the straight line graph. Answer: breaking stress,true stress at fracture and limit of proportionality.
In a forming process the diameter of the specimen is 1 cm and its length changes from 50 mm to 60 mm. Show the maximum force value on the graph of Force vs. True Strain plotted in Excel Program or any plotting program not by hand using the flow stress equation given below. σ= Kεn and σ=F/A Where the parameters are σ : True Stress in MPa K: Strength Coefficient, K=210 in MPa ε : True Strain, ε=ln (l/l0) n: Strain Hardening Exponent, n=0.27 F: Force in 10 A : Area in mm2 Take at least 3 digits after the decimal point. Specify the units. You can use Excel or any plotting program not by hand then paste your graph into the solution section.
The following data were obtained from the tensile test of Aluminum alloy. The initial diameter of testspecimen was 0.505 inch and gauge length was 2.0 inch. Plot the stress strain diagram and determine(a) Proportional Limit (b) Modulus of Elasticity (c) Yield Stress at 0.2% offset (d) Ultimate Stress and(e) Nominal Rupture Stress.
The length of a iron bar is measured by a number of different observers and the following set of 12measurements are recorded (units mm)302,304,303,305,307,309,310,311,312,301,303,302. Find the values of mean, median, variance andstandard deviation.
a . Sketch stress strain curve if the result shown in table represent the force and extension happened in steel, and show Mechanical properties that we get from tensile test on curve? (10p)Note : Lo=80 mm , Do=10 mm , use excel to plot the curve ExtensionLoad(mm) (N)0 0.900.83 4694.341.67 4831.412.50 4781.083.33 4918.834.17 4926.585.00 5257.075.83 5437.016.66 5575.888.33 5775.189.16 5847.5210.83 5965.4111.67 6010.5312.50 6042.5713.33 6072.2614.16 6092.9315.00 6113.2416.67 6140.3617.50 6146.3718.33 6148.1419.16 6149.1725.00 5940.2125.83 5675.3326.67 4725.52b. What is meant by modulus of rigidity? if it increases what does happen to material? (2p)
In a stress strain curve of mild steel, the elastic limit will be before the limit of proportionality . Select one: True False
Help in filling table: Material Yield Strength (MPa) Elastic Modulus-E (GPa) Poisson’s ratio Ultimate Strength (MPa) Steel 0.305 Aluminum 69 0.33 Copper 123 0.33 Brass 88 0.33
SHOW COMPLETE SOLUTION AND FINAL ANSWER INTO 3 DECIMAL PLACES 1. A spherical tank for storing gas under a pressure is 20 m in diameter and is made of steel 20 mm thick. The yield point of the material is 240 MPa. If a factor of safety of 2 is desired, what is the maximum permissible internal pressure that the tank can hold?